Mercedes-Benz A2D-MBR User manual

Courtesy of: DiscountCarStereo.com
Serving the internet community since 1995
A2D-MBR
QUICK INSTALLATION GUIDE FOR SELECT 1994-98 MERCEDES BENZ

PRODUCT SAFETY & DISCLAIMER
READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE
PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY
•This installation guide is provided as a GENERAL installation guide, some vehicles vary and
may require additional steps. We do not accept responsibility for third party labor charges
or modifications. Exercise due-diligence when installing this product.
•We do not accept any responsibility for vehicle damage or personal injury resulting from
the installation of this product.
•Careless installation and operation can result in equipment damage.
Requirement:
CD changer controlling radio
Introduction
Just because you drive an older car does not mean you have to settle for old
technology. In order to stay up to speed with fast changing technology, many
Mercedes owners have opted to change the factory radio in favor of one that
offers modern features such as Bluetooth, navigation etc. but did you know the
factory radio is also able to support these features? All you need is a
smartphone and the A2D-MBR. Upgrade factory radio in select 1994-98
Mercedes Benz to support music streaming, navigation, audio books, and more.
Simply connect module to 10-pin CD changer port behind radio, pair smart
device (e.g., Smartphone, iPad, Tablet, Kindle etc.) and enjoy favorite music
application on the car speaker system! Installing the A2D-MBR means optional
CD changer (if present), must be disconnected, however; to retain the CD
changer, purchase our A2D-MBRCD instead.
Installation
Installing this module requires radio removal
Remove radio from dashboard to gain access to connectors. A special removal
tools (See Fig. 1) is required (not included)
Fig. 1
removal tool
MB radios pictured above, do not apply.
1. Slide tools (straight edge facing away) into radio slots to detent
position. Withdraw radio by pulling outwards on the tools. See Fig. 2
Click here for more detailed radio removal instructions.

Fig. 2
2. Disconnect factory 10-pin plug (if present) from radio (C) chamber
3. Connect module 10-pin plug (See Fig. 3) to radio (C) chamber (See Fig.
4)
Fig. 3
10-pin plug
Fig. 4
Radio chambers
Optional remote control
This optional wireless remote is not required for the A2D-MBR to work; however,
instead of trying to juggle a phone while steering, simply press the remote
buttons which can be mounted to steering wheel or dashboard. Remote does not
operate radio functions.
Remote control functions:
1. Control music wirelessly
2. Switch between sources
3. Track up/down
4. Volume up/down
Pairing remote:

Remote operation:
Use wireless remote to perform the following functions on any iOS7.0 and higher
or Android 4.4 and higher.
Contents:
Optional Noise filter
As with many older vehicles, adding additional accessories to the electrical
circuit are prone to produce noise (whine). The optional noise filter (See Fig. 5)
helps eliminate these annoyances that may or may not be present. If you opt to
not included the filter, you may purchase as a DIY.
Fig. 5
Pairing module
Pairing process varies among devices but the basic steps are the same. Pairing
is done upon initial install and will not have to be repeated.
1. Turn radio “ON”, Press “CD”button
2. On smart device: Go to Bluetooth Settings and turn it on
3. Tap “ Scan” or “Search” for devices .
4. Wait for device name (See Fig. 6) to appear and select it
5. Confirmation tone “Connected”is announced on car speakers.
Fig. 6
6. Confirmation tone (connected) will play on car speakers.

Operation
1. Turn ignition and radio “ON”
2. Press "CD” button on radio
Note: If radio does not switch to CD, cycle ignition OFF/ON and try again.
3. Launch smart device music app
4. Use radio volume control button to set the playback level. Make certain
device volume is set 85% or more. If playback is distorted, lower
volume on device.
Warning: Playlist and Track selection is *NOT* possible from the radio.
You must use the iPod built-in controls to access music files
5. If correct operation is confirmed go ahead and reinstall radio.
Fig. 7
1999-Up radios with digital optic port do not apply
Frequent ask questions & Troubleshooting
1. Does the A2D-MBR work in vehicles with CD changer?
YES; but the CD changer must be disconnected.
2. Does the A2D-MBR work on all Mercedes radios?
NO; works on 1994-98 Becker BE1492, BE1692, BE2210, BE1350) Alpine
CM2296 and CM2396 radios.
Note: In some countries, the above-mentioned radios were installed in
vehicles as early as 1992 and up until early 1999; however, late 1999-
Up Mercedes Audio 10, 20, 30, 50 PCM etc. (See Fig. 7) are not
compatible.
3. Can I control Smartphone or Tablet from the radio buttons?
NO; Except volume; you must use Smartphone or Tablet built-in controls
and display or optional wireless remote control.
4. My Mercedes radio also has the 10-pin connector seen in Fig. 6. Does
the A2D-MBR work on these radios?
NO;Mercedes radios with digital port (e.g., Audio 10, 20, 30, 50, PCM)
are NOT compatible.
5. Will I be able to make phone calls using this module?
NO; Purchase our A2DIY-MBCD
6. What happens when streaming music app and a call comes in?
Streaming is muted, call number announced. Answer call using handset.
Streaming resumes once call has ended.
7. Can I pair or save more than one device to the A2D-MBR?
YES; more than one device (slaves) can be paired however only one
connection can be active at a time.
Disclaimer
• This product has no affiliation with Mercedes Benz, Alpine or Becker
• We’re not liable for misuse of this product.
Email [e-mail]
© 1995-Feb-22 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademarks or registered trademarks of their respective companies or mark holders.