Mercers Furniture Corona 2 User manual

Corona 2 Door Wardrobe
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
Page 1
SEC/WG/03/17/MY1
51209(MY)
FOR DOMESTIC USE ONLY

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
FITTINGS
PARTS LIST
Page 2
02
22
05
05
16
07
13
14
06
19
19
03
09
20 17
18
01
13
21
10
21
04
08
12
11
15
Top back Plinth
Top Front Plinth
Side Plinth
Hanger support
Top Middle Plinth
Support block
Top Panel (Small)
Back Panel
Base
Left Side Panel
Front Plinth
Bottom back panel strip
Right Side Panel
Hanging rail
Right Door
Top Side Plinth
Upper back panel strip
Fixed Shelf
Door Strip
Left front upright
Left Door
Right front upright
A29
B 28
C14
4,5x30
3,5x30
D32
3,5x16
E 52
10x10
Ø8x30
J
K06
4,5x25
L03
4,0x45
M 02
Ø8x40
N02
F04
G04
H06
4,0x20
I02
06
O
2x
1x
1x
01
SEC/WG/03/17/MY1

Page 3
01
14 04
03
19
19
20
01
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
Assemble on a clean
soft surface to
avoid damage.
CC
C
C
22
B28
M
M
Ø8x30
M02
Ø8x40
B
B
C
02
19
B
B
B
C06
3,5x30
SEC/WG/03/17/MY1

Page 4
K
K
C
C
C
C
K
K
C
K
Assemble on a clean
soft surface to
avoid damage.
02
03
18
17
20
C08
3,5x30
K06
4,5x25
L03
4,0x45
4,5x30
03
09
13
02
13
10
K
K
A
A
A
A
A
A
21
21
A
A 06
SEC/WG/03/17/MY1

Page 5
A
04
03
02 01
14
04
A 18
4,5x30
A03
4,5x30
14
05
08
A
A
A
Please note that the
smaller panel (1)
should be attached
at the top
SEC/WG/03/17/MY1

A
A
06
07
06
18
A 02
4,5x30
Page 6
SEC/WG/03/17/MY1

D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
EE
G
G
EE
EE
G
G
G
G
EE
08
09
EE
G
G
EE
05
05
07
16
16
07
D32
10x10
3,5x16
E08
G04
Page 7
* For your future reference
SPD Number should be here
00000
SEC/WG/03/17/MY1

180°
10
Assemble on a clean
soft surface to
avoid damage.
12
12
11
11
3,5x16
E26
F04
I02
J06
4,0x20
H06
Page 8
E
E
E
J
J
J
J
E
E
E
I
II
I
EE
E
E
EE
FF
FF
180°
E
E
E
J
J
J
J
E
E
E
I
I
I
I
15
15
E
H
E
F
H
H
H
H
H
H
E
E
SEC/WG/03/17/MY1

EE
E
11
WHEN FITTING THE DOOR HINGES
( J ) CAREFULLY LINE UP THE
SCREW HOLES WITH THOSE
PRE-MARKED ON THE SIDE, THIS
WILL ENSURE THE DOORS HANG
CORRECTLY.
12
11
3,5x16
E18
N02
Page 9
Wall
Top
Top
Wall Top
3,5 x 25mm (1x)
Serious or fatal injuries can occur from furniture tipping
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.
Please make sure you use fixings suitable for the walls in your home.
SEC/WG/03/17/MY1