Merco TS2 Series User manual

Installation and Operation Manual
Thermal Shelves
TS2 and TS2-B Series
I&W #07.05.238.00
Do not operate this equipment unless you have
read and understood the contents of this manual!
Failure to follow the instructions contained in this
manual may result in serious injury or death. This
manual contains important safety information
concerning the maintenance, use, and operation
of this product. If you’re unable to understand the
contents of this manual, please bring it to the
attention of your supervisor. Keep this manual in a
safe location for future reference.
o opere este equipo al menos que haya leído y
comprendido el contenido de este manual!
Cualquier falla en el seguimiento de las
instrucciones contenidas en este manual puede
resultar en un serio lesión o muerte. Este manual
contiene importante información sobre seguridad
concerniente al mantenimiento, uso y operación
de este producto. Si usted no puede entender el
contenido de este manual por favor pregunte a su
supervisor. Almacenar este manual en una
localización segura para la referencia futura.
© 2010 Merco, LLC

CO TE TS
iForm No. TS2M-0210
I TRODUCTIO
Merco Thermal Shelves are designed to keep prepared foods
hot in kitchen work areas, server pick-up stations, or customer
serving points. They will keep all foods at optimum serving
temperatures without affecting quality. These warmers have a
thermostatically-controlled heated base to extend the holding
times of most foods.
Thermal Shelves are a product of extensive research and field
testing. The materials used were selected for maximum
durability, attractive appearance, and optimum performance.
Every unit is inspected and tested thoroughly prior to shipment.
This manual provides the installation, safety, and operating
instructions for Merco Thermal Shelves. Merco recommends all
installation, operating, and safety instructions appearing in this
manual be read prior to installation or operation of a Thermal
Shelf.
Safety information that appears in this manual is identified by
the following signal word panels:
WAR I G indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTIO indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
OTICE is used to address practices not related to
personal injury.
WARNING
NOTICE
CAUTION
Important Owner Information ...............................................i
Introduction............................................................................i
Important Safety Information...............................................1
Model Descriptions...............................................................2
TS2 Model .......................................................................2
TS2-B Models..................................................................2
Model Designation................................................................2
Specifications........................................................................3
Plug Configurations .........................................................3
Dimensions — TS2-XX Models.......................................3
Dimensions — TS2-XXB Recessed Top Models ............4
Dimensions — TS2-XXB Flat Top Models.......................4
Electrical Rating Chart — TS2-XX Models......................5
Electrical Rating Chart — TS2-XXB Recessed and
Flat Top Models ............................................................6
Installation .............................................................................7
General............................................................................7
TS2 Models .....................................................................7
TS2-B Models..................................................................7
Operation.............................................................................10
Maintenance ........................................................................11
Cleaning.........................................................................11
Troubleshooting Guide ......................................................12
Options and Accessories...................................................13
Merco Limited Warranty.......................................Back Page
IMPORTA T OW ER I FORMATIO
Record the model number, serial number (specification label on
bottom of TS2 model, bottom of control box on TS2-B models),
voltage, and purchase date of the unit in the spaces below.
Please have this information available when calling Merco for
service assistance.
Model No. ____________________________________
Serial No. ____________________________________
Voltage ______________________________________
Date of Purchase ______________________________
Business 8:00 AM to 5:00 PM
Hours: Central Standard Time (C.S.T.)
Telephone: [phone] (Technical Support)
888.417.5462 (Customer Service)
Merco, LLC
1111 North Hadley Road
Fort Wayne, Indiana 46804
United States of America
Additional information can be found by visiting our web site at
www.mercoproducts.com.

IMPORTA T SAFETY I FORMATIO
Form No. TS2M-0210 1
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Turn power switch OFF, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO OT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Do not steam clean or use excessive water on unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. The cord must be replaced by Merco, a Factory
Authorized Service Agent, or a person with similar
qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Original Equipment Manufacturer (OEM)
Replacement Parts when service is required. Failure to
use OEM Replacement Parts will void all warranties and
may subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
OEM Replacement Parts are specified to operate safely
in the environments in which they are used. Some
aftermarket or generic replacement parts do not have
the characteristics that will allow them to operate safely
in Merco equipment.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Make sure food product has been heated to the proper food-
safe temperature before placing on the unit. Failure to heat
food product properly may result in serious health risks. This
unit is for holding preheated food product only.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact a Factory Authorized Service
Agent or contact the Merco Service Department at
800-506-9565.
WARNING
BUR HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
Do not operate built-in models without control box
mounted properly as described in the installation
instructions.
The ational Sanitation Foundation ( SF) requires that
units over 36″ (914 mm) in width or weighing more than 80
lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point of
use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
Unit is recommended for use in metallic countertops.
Damage to non-metallic countertop material caused by
heat generated from this equipment is not covered under
unit warranty. For other surfaces, verify that the material is
suitable for temperatures up to 200°F (93°C).
Built-in units must not have a setpoint temperature higher
than 200°F (93°C). Temperatures exceeding 200°F (93°C)
will damage unit and void warranty.
Do not modify wiring or cut thermostat capillary wire on
control box to increase remote mounting distance. Cutting
thermostat capillary wire will cause unit to overheat and
may damage unit as well as surrounding countertop.
Do not use excessive force when tightening mounting
screws on built-in units. This may damage unit and/or
countertop.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Use non-abrasive cleaners only. Abrasive cleaners could
scratch the finish of the unit, marring its appearance and
making it susceptible to soil accumulation.
NOTICE
CAUTION
Read the following important safety information before using this equipment to avoid serious injury or death
and to avoid damage to equipment or property.

MODEL DESCRIPTIO
2Form No. TS2M-0210
MODEL DESIG ATIO
TS2 Model
The Thermal Shelf is ideal for pass-through areas, buffet lines,
or as a heated work shelf. It features an illuminated Power
On/Off switch, 80° to 200°F (27° to 93°C) adjustable thermostat,
and 6′ (1829 mm) power cord with plug. Surface mounted,
blanket-type foil elements distribute heat under the entire
stainless steel or hardcoat aluminum surface.
All TS2 models are shipped from the factory completely
assembled and ready for use.
Figure 1. TS2 Model
TS2-B Models
TS2-B Built-In Thermal Shelves have either a hardcoat
aluminum or stainless steel surface and a blanket-type foil
element for uniform heat distribution. Ideal for server-to-
customer pass-through areas, buffet/ cafeteria lines, and other
self-service areas.
A 36″ (914 mm) flexible conduit channels the power lines from
the shelf to a remote control box. The control box comes with a
control thermostat with a range of 80° to 200°F (27° to 93°C),
an illuminated POWER On/Off (I/O) switch, and mounting
brackets. The attached control box can be located up to 36″
(914 mm) from the unit. A 6′ (1829 mm) cord and plug is
attached to the control box.
TS2-B Thermal Shelves are available with two different styles of
tops — recessed top and flat top. Recessed top models have a
3/4″ (19 mm) flanged edge that allows the unit to drop into a
countertop opening for recessed mounting. Flat top models
have a single piece, flat top that rests on the countertop for a
continuous, “flush” look with the countertop. The shelves are
easy to clean with a soft damp cloth or non-abrasive cleaner. All
TS2-B models are shipped from the factory completely
assembled and ready for use.
Figure 2. TS2-B Models
TS2-B Recessed Top Model
TS2-B Flat Top Model
TS2-XXBF
Thermal Shelf
Second Generation Built-In
Flat Top
Width (inches)
Figure 3. Model Designation

SPECIFICATIO S
Form No. TS2M-0210 3
Figure 5. TS2 Model Dimensions
Dimensions — TS2-XX Models
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the applications.
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage, size,
and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install the proper voltage and size electrical receptacle.
NOTE: The specification la el is located on the ottom of TS2
models and the ottom of the control ox on TS2-B
models. See la el for serial num er and verification of
unit electrical information.
WARNING
Footprint Footprint
Model Width (A) Depth (B) Height (C) Width (D) Depth (E)
TS2-18 18″ (457 mm) 19-1/2″ (495 mm) 2-3/8″ (60 mm)† 16-3/4″ (425 mm) 18″ (457 mm)
TS2-24 24″ (610 mm) 19-1/2″ (495 mm) 2-3/8″ (60 mm)† 22-3/4″ (578 mm) 18″ (457 mm)
TS2-30 30″ (762 mm) 19-1/2″ (495 mm) 2-3/8″ (60 mm)† 28-3/4″ (730 mm) 18″ (457 mm)
TS2-36 36″ (914 mm) 19-1/2″ (495 mm) 2-3/8″ (60 mm)† 34-3/4″ (883 mm) 18″ (457 mm)
TS2-42 42″ (1067 mm) 19-1/2″ (495 mm) 5-3/8″ (137 mm)* 40-3/4″ (1035 mm) 18″ (457 mm)
TS2-48 48″ (1219 mm) 19-1/2″ (495 mm) 5-3/8″ (137 mm)* 46-3/4″ (1187 mm) 18″ (457 mm)
TS2-54 54″ (1372 mm) 19-1/2″ (495 mm) 5-3/8″ (137 mm)* 52-3/4″ (1340 mm) 18″ (457 mm)
TS2-60 60″ (1524 mm) 19-1/2″ (495 mm) 5-3/8″ (137 mm)* 58-3/4″ (1492 mm) 18″ (457 mm)
TS2-66 66″ (1676 mm) 19-1/2″ (495 mm) 5-3/8″ (137 mm)* 64-3/4″ (1645 mm) 18″ (457 mm)
TS2-72 72″ (1829 mm) 19-1/2″ (495 mm) 5-3/8″ (137 mm)* 70-3/4″ (1797 mm) 18″ (457 mm)
D
B
Front View Side View
A
C
E
†Height includes 1″ (25 mm) legs.
*Height includes 4″ (102 mm) legs.
Figure 4. Plug Configurations
NOTE: Receptacle not supplied y Merco.
NEMA 5-15P NEMA 5-20P
NEMA 6-15P
CEE 7/7 Schuko BS-1363

SPECIFICATIO S
4Form No. TS2M-0210
Heated Heated
Model Width (A) Width (B) Width (C) Depth (D) Depth (E) Height (F) Height (G)
TS2-24B 25-1/2″ (648 mm) 24″ (610 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-30B 31-1/2″ (800 mm) 30″ (762 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-36B 37-1/2″ (953 mm) 36″ (914 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-42B 43-1/2″ (1105 mm) 42″ (1067 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-48B 49-1/2″ (1257 mm) 48″ (1219 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-54B 55-1/2″ (1410 mm) 54″ (1372 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-60B 61-1/2″ (1562 mm) 60″ (1524 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-66B 67-1/2″ (1715 mm) 66″ (1676 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
TS2-72B 73-1/2″ (1867 mm) 72″ (18291 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-7/8″ (73 mm) 2-1/16″ (52 mm)
A
B
C
F
G
Front View Side View
E
F
Dimensions — TS2-XXB Recessed Top Models
Heated Heated
Model Width (A) Width (B) Width (C) Depth (D) Depth (E) Height (F) Height (G)
TS2-24B 25-1/2″ (648 mm) 24-3/32″ (612 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-30B 31-1/2″ (800 mm) 30-3/32″ (764 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-36B 37-1/2″ (953 mm) 36-3/32″ (917 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-42B 43-1/2″ (953 mm) 42-3/32″ (1069 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-48B 49-1/2″ (1257 mm) 48-3/32″ (1222 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-54B 55-1/2″ (1410 mm) 54-3/32″ (1374 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-60B 61-1/2″ (1562 mm) 60-3/32″ (1526 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-66B 67-1/2″ (1715 mm) 66-3/32″ (1679 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
TS2-72B 73-1/2″ (1867 mm) 72-3/32″ (1831 mm) 7-1/16″ (179 mm) 19-1/2″ (495 mm) 21″ (533 mm) 2-1/4″ (57 mm) 2-1/16″ (52 mm)
Dimensions — TS2-XXB Flat Top Models
Figure 7. TS2-XXB, Flat Top Model Dimensions
A
B
C
F
G
Front View Side View
E
F
Figure 6. TS2-XXB, Recessed Top Model Dimensions
NOTICE: Refer to the I STALLATIO section of this manual for actual countertop cutout dimensions.

SPECIFICATIO S
Form No. TS2M-0210 5
Plug Shipping
Model Voltage Watts Amps Configuration Weight
TS2-18 100 250 2.5 NEMA 5-15P 16 lbs. (7 kg)
120 250 2.1 NEMA 5-15P 16 lbs. (7 kg)
220 228 1.0 CEE 7/7 Schuko 16 lbs. (7 kg)
240 272 1.1 BS-1363 16 lbs. (7 kg)
220–230 (CE) 228–250 1.0–1.1 CEE 7/7 Schuko 16 lbs. (7 kg)
230–240 (CE) 250–272 1.1 BS-1363 16 lbs. (7 kg)
TS2-24 100 350 3.5 NEMA 5-15P 20 lbs. (9 kg)
120 350 2.9 NEMA 5-15P 20 lbs. (9 kg)
220 320 1.5 CEE 7/7 Schuko 20 lbs. (9 kg)
240 380 1.6 BS-1363 20 lbs. (9 kg)
220–230 (CE) 320–350 1.5–1.6 CEE 7/7 Schuko 20 lbs. (9 kg)
230–240 (CE) 350–380 1.5–1.6 BS-1363 20 lbs. (9 kg)
TS2-30 100 450 4.5 NEMA 5-15P 25 lbs. (11 kg)
120 450 3.8 NEMA 5-15P 25 lbs. (11 kg)
220 412 1.9 CEE 7/7 Schuko 25 lbs. (11 kg)
240 490 2.0 BS-1363 25 lbs. (11 kg)
220–230 (CE) 412–450 1.9–2.0 CEE 7/7 Schuko 25 lbs. (11 kg)
230–240 (CE) 450–490 2.0 BS-1363 25 lbs. (11 kg)
TS2-36 100 550 5.5 NEMA 5-15P 28 lbs. (13 kg)
120 550 4.6 NEMA 5-15P 28 lbs. (13 kg)
220 504 2.3 CEE 7/7 Schuko 28 lbs. (13 kg)
240 598 2.5 BS-1363 28 lbs. (13 kg)
220–230 (CE) 504–550 2.3–2.4 CEE 7/7 Schuko 28 lbs. (13 kg)
230–240 (CE) 550–598 2.4–2.5 BS-1363 28 lbs. (13 kg)
TS2-42 100 600 6.0 NEMA 5-15P 32 lbs. (15 kg)
120 600 5.0 NEMA 5-15P 32 lbs. (15 kg)
220 548 2.5 CEE 7/7 Schuko 32 lbs. (15 kg)
240 652 2.7 BS-1363 32 lbs. (15 kg)
220–230 (CE) 548–600 2.5–2.6 CEE 7/7 Schuko 32 lbs. (15 kg)
230–240 (CE) 600–652 2.6–2.7 BS-1363 32 lbs. (15 kg)
TS2-48 100 700 7.0 NEMA 5-15P 36 lbs. (16 kg)
120 700 5.8 NEMA 5-15P 36 lbs. (16 kg)
220 640 3.0 CEE 7/7 Schuko 36 lbs. (16 kg)
240 760 3.2 BS-1363 36 lbs. (16 kg)
220–230 (CE) 640–700 2.9–3.0 CEE 7/7 Schuko 36 lbs. (16 kg)
230–240 (CE) 700–760 3.0–3.2 BS-1363 36 lbs. (16 kg)
TS2-54 100 800 8.0 NEMA 5-15P 42 lbs. (19 kg)
120 800 6.7 NEMA 5-15P 42 lbs. (19 kg)
220 732 3.3 CEE 7/7 Schuko 42 lbs. (19 kg)
240 870 3.6 BS-1363 42 lbs. (19 kg)
220–230 (CE) 732–800 3.3–3.5 CEE 7/7 Schuko 42 lbs. (19 kg)
230–240 (CE) 800–870 3.5–3.6 BS-1363 42 lbs. (19 kg)
TS2-60 100 900 9.0 NEMA 5-15P 44 lbs. (20 kg)
120 900 7.5 NEMA 5-15P 44 lbs. (20 kg)
220 824 3.7 CEE 7/7 Schuko 44 lbs. (20 kg)
240 980 4.1 BS-1363 44 lbs. (20 kg)
220–230 (CE) 824–900 3.7–3.9 CEE 7/7 Schuko 44 lbs. (20 kg)
230–240 (CE) 900–980 3.9–4.1 BS-1363 44 lbs. (20 kg)
TS2-66 100 1000 10.0 NEMA 5-15P 50 lbs. (23 kg)
120 1000 8.3 NEMA 5-15P 50 lbs. (23 kg)
220 916 4.2 CEE 7/7 Schuko 50 lbs. (23 kg)
240 1088 4.5 BS-1363 50 lbs. (23 kg)
220–230 (CE) 916–1000 4.2–4.3 CEE-Schuko 50 lbs. (23 kg)
230–240 (CE) 1000–1088 4.3–4.5 BS-1363 50 lbs. (23 kg)
TS2-72 100 1100 11.0 NEMA 5-15P 56 lbs. (25 kg)
120 1100 9.2 NEMA 5-15P 56 lbs. (25 kg)
220 1008 4.6 CEE 7/7 Schuko 56 lbs. (25 kg)
240 1196 5.0 BS-1363 56 lbs. (25 kg)
220–230 (CE) 1008–1100 4.6–4.8 CEE 7/7 Schuko 56 lbs. (25 kg)
230–240 (CE) 1100–1196 4.8–5.0 BS-1363 56 lbs. (25 kg)
The shaded areas contain electrical information for International models only.
Electrical Rating Chart — TS2-XX Models

Plug Shipping
Model Voltage Watts Amps Configuration Weight
TS2-24B 100 550 5.5 NEMA 5-15P 22 lbs. (10 kg)
120 550 4.6 NEMA 5-15P 22 lbs. (10 kg)
220 550 2.5 CEE 7/7 Schuko 22 lbs. (10 kg)
240 550 2.3 BS-1363 22 lbs. (10 kg)
220–230 (CE) 550–601 2.5–2.6 CEE 7/7 Schuko 22 lbs. (10 kg)
230–240 (CE) 505–550 2.2–2.3 BS-1363 22 lbs. (10 kg)
TS2-30B 100 665 6.7 NEMA 5-15P 25 lbs. (11 kg)
120 665 5.5 NEMA 5-15P 25 lbs. (11 kg)
220 665 3.0 CEE 7/7 Schuko 25 lbs. (11 kg)
240 665 2.8 BS-1363 25 lbs. (11 kg)
220–230 (CE) 665–727 3.0–3.2 CEE 7/7 Schuko 25 lbs. (11 kg)
230–240 (CE) 611–665 2.7–2.8 BS-1363 25 lbs. (11 kg)
TS2-36B 100 780 7.8 NEMA 5-15P 29 lbs. (13 kg)
120 780 6.5 NEMA 5-15P 29 lbs. (13 kg)
220 780 3.5 CEE 7/7 Schuko 29 lbs. (13 kg)
240 780 3.3 BS-1363 29 lbs. (13 kg)
220–230 (CE) 780–853 3.5–3.7 CEE 7/7 Schuko 29 lbs. (13 kg)
230–240 (CE) 716–780 3.1–3.3 BS-1363 29 lbs. (13 kg)
TS2-42B 100 885 8.9 NEMA 5-15P 32 lbs. (15 kg)
120 885 7.4 NEMA 5-15P 32 lbs. (15 kg)
220 885 4.0 CEE 7/7 Schuko 32 lbs. (15 kg)
240 885 3.7 BS-1363 32 lbs. (15 kg)
220–230 (CE) 885–967 4.0–4.2 CEE 7/7 Schuko 32 lbs. (15 kg)
230–240 (CE) 813–885 3.5–3.7 BS-1363 32 lbs. (15 kg)
TS2-48B 100 1000 10.0 NEMA 5-15P 36 lbs. (16 kg)
120 1000 8.3 NEMA 5-15P 36 lbs. (16 kg)
220 1000 4.5 CEE 7/7 Schuko 36 lbs. (16 kg)
240 1000 4.2 BS-1363 36 lbs. (16 kg)
220–230 (CE) 1000–1093 4.5–4.7 CEE 7/7 Schuko 36 lbs. (16 kg)
230–240 (CE) 918–1000 4.0–4.2 BS-1363 36 lbs. (16 kg)
TS2-54B 100 1110 11.1 NEMA 5-15P 43 lbs. (20 kg)
120 1110 9.3 NEMA 5-15P 43 lbs. (20 kg)
220 1110 5.0 CEE 7/7 Schuko 43 lbs. (20 kg)
240 1110 4.6 BS-1363 43 lbs. (20 kg)
220–230 (CE) 1110–1213 5.0–5.3 CEE 7/7 Schuko 43 lbs. (20 kg)
230–240 (CE) 1019–1110 4.4–4.6 BS-1363 43 lbs. (20 kg)
TS2-60B 100 1220 12.2 NEMA 5-15P 50 lbs. (23 kg)
120 1220 10.2 NEMA 5-15P 50 lbs. (23 kg)
220 1220 5.5 CEE 7/7 Schuko 50 lbs. (23 kg)
240 1220 5.1 BS-1363 50 lbs. (23 kg)
220–230 (CE) 1220–1333 5.5–5.8 CEE 7/7 Schuko 50 lbs. (23 kg)
230–240 (CE) 1120–1220 4.9–5.1 BS-1363 50 lbs. (23 kg)
TS2-66B 100 1330 13.3 NEMA 5-15P 54 lbs. (24 kg)
120 1330 11.1 NEMA 5-15P 54 lbs. (24 kg)
220 1330 6.0 CEE 7/7 Schuko 54 lbs. (24 kg)
240 1330 5.5 BS-1363 54 lbs. (24 kg)
220–230 (CE) 1330–1454 6.0–6.3 CEE 7/7 Schuko 54 lbs. (24 kg)
230–240 (CE) 1221–1330 5.3–5.5 BS-1363 54 lbs. (24 kg)
TS2-72B 100 1440 14.4 NEMA 5-15P 58 lbs. (23 kg)
120 1440 12.0 NEMA 5-15P 58 lbs. (26 kg)
220 1440 6.5 CEE 7/7 Schuko 58 lbs. (26 kg)
240 1440 6.0 BS-1363 58 lbs. (26 kg)
220–230 (CE) 1440–1574 6.5–6.8 CEE 7/7 Schuko 58 lbs. (26 kg)
230–240 (CE) 1322–1440 5.8–6.0 BS-1363 58 lbs. (26 kg)
SPECIFICATIO S
6Form No. TS2M-0210
Electrical Rating Chart — TS2-XXB Recessed Top and Flat Top Models
The shaded areas contain electrical information for International models only.

I STALLATIO
Form No. TS2M-0210 7
General
Use the following procedures to install the TS2 and TS2-B units.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
Do not operate built-in models without control box
mounted properly as described in the installation
instructions.
The ational Sanitation Foundation ( SF) requires that
units over 36″ (914 mm) in width or weighing more than 80
lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point of
use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
Unit is recommended for use in metallic countertops.
Damage to non-metallic countertop material caused by
heat generated from this equipment is not covered under
unit warranty. For other surfaces, verify that the material
is suitable for temperatures up to 200°F (93°C).
TS2 Models
1. Remove the unit from the carton and place it upside down
on the cardboard.
2. Install the four feet into the corner holes on the base.
Tighten securely, but do not over-tighten.
NOTE: If 4″ (102 mm) legs are required, refer to the OPTIONS
AND ACCESSORIES section in this manual for
installation instructions.
3. Place one rubber boot over each metal foot (for 1″ [25 mm]
feet only).
4. Turn unit upright, and place unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70° F (21° C).
Avoid areas that may be subject to active air movements
or currents (i.e., near exterior doors, exhaust fans/hoods,
air conditioning ducts, etc...).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
NOTICE
CAUTION
WARNING
TS2-B Models
1. Remove the unit from the carton and place it upside down
on the cardboard.
Figure 8. Underside of TS2-B Models
2. Remove and save the four bracket screws from the
underside of the unit.
NOTE: The control ox may e moved to the most convenient
location on the underside of the unit. For semi-remote
installations, leave the control ox in place until the unit
is placed into the countertop (see Figure 9).
3. Prepare countertop opening. Refer to the appropriate
“Countertop Cutout” chart on the following page for
recommended countertop cutout dimensions.
4. Apply a bead of NSF-approved sealant between the
countertop material and the mounting flange on the unit. The
sealant must be rated for use at a minimum temperature of
250° F (121° C).
5. Place the unit into the countertop opening.
6. Assemble the Z-brackets to the underside of the unit using
the four bracket screws removed earlier in this procedure
(see Figures 10 and 11).
NOTE: Units 48″ (1219 mm) or longer require two additional Z-
rackets to e installed midway along the front and rear
of the unit.
7. Adjust the mounting screws on the Z-brackets until the top
flange lies flat on the countertop.
Do not use excessive force when tightening mounting
screws on built-in units. This may damage unit and/or
countertop.
continued...
Bracket Screw
NOTICE

I STALLATIO
8Form No. TS2M-0210
Countertop Cutout — TS2-B Recessed Top Models
Model Minimum Width Maximum Width Minimum Depth Maximum Depth
TS2-24B 24-1/2″ (622 mm) 24-3/4″ (629 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-30B 30-1/2″ (775 mm) 30-3/4″ (781 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-36B 36-1/2″ (927 mm) 36-3/4″ (934 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-42B 42-1/2″ (1080 mm) 42-3/4″ (1086 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-48B 48-1/2″ (1232 mm) 48-3/4″ (1238 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-54B 54-1/2″ (1384 mm) 54-3/4″ (1391 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-60B 60-1/2″ (1537 mm) 60-3/4″ (1543 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-66B 66-1/2″ (1689 mm) 66-3/4″ (1695 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-72B 72-1/2″ (1842 mm) 72-3/4″ (1848 mm) 20″ (508 mm) 20-1/4″ (514 mm)
Bracket Screw
Metallic
Countertop
Mounting Screw
Z-Bracket
Apply a bead of NSF-approved sealant between the
countertop and the mounting flange on the unit. Sealant
must be rated for use at a minimum temperature of 250° F (121° C).
Figure 10. TS2-B Recessed Top Model Installation
8. Remove any excess sealant.
9. If desired or necessary, the control box can be mounted in
a semi-remote location.
a. Remove the control box from the bottom of the unit.
b. If necessary, remove the end brackets from the control
box, rotate and reposition them.
c. The remote control box can be panel, surface, under-
counter, or recess mounted. If recess mounting, The
control box will require a hole mounting pattern of
7-5/8″ W x 1-1/4″ H (194 mm x 32 mm) for #8 screws.
Figure 9. Remote Control Box Mounting Options
RecessPanel
Under Counter
Surface
d. The distance the remote control box can be mounted
from the unit is determined by the 36″ (914 mm) conduit.
Do not pull the conduit tight to increase the mounting
distance. The conduit should have some slack after the
control box is mounted.
Do not modify wiring or cut thermostat capillary wire on
control box to increase-remote mounting distance. Cutting
the thermostat capillary wire will cause the unit to overheat
and may damage the unit as well as the surrounding
countertop.
10. Once all components are secured, proceed to the
OPERATION section.
NOTE: A 6′ (1829 mm) cord is supplied with this unit; any
excess cord should e neatly routed so it does not hang
down.
NOTICE

I STALLATIO
Form No. TS2M-0210 9
Countertop Cutout — TS2-B Flat Top Models
Model Minimum Width Maximum Width Minimum Depth Maximum Depth
TS2-24B 24-1/2″ (622 mm) 24-3/4″ (629 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-30B 30-1/2″ (775 mm) 30-3/4″ (781 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-36B 36-1/2″ (927 mm) 36-3/4″ (934 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-42B 42-1/2″ (1080 mm) 42-3/4″ (1086 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-48B 48-1/2″ (1232 mm) 48-3/4″ (1238 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-54B 54-1/2″ (1384 mm) 54-3/4″ (1391 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-60B 60-1/2″ (1537 mm) 60-3/4″ (1543 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-66B 66-1/2″ (1689 mm) 66-3/4″ (1695 mm) 20″ (508 mm) 20-1/4″ (514 mm)
TS2-72B 72-1/2″ (1842 mm) 72-3/4″ (1848 mm) 20″ (508 mm) 20-1/4″ (514 mm)
Metallic
Countertop
Mounting Screw
Bracket Screw
Z-Bracket
Apply a bead of NSF-approved sealant between the
countertop and the unit. Sealant must be rated for
use at a minimum temperature of 250° F (121° C).
Figure 11. TS2-B Flat Top Model Installation

OPERATIO
10 Form No. TS2M-0210
General
Use the following procedure to turn on and operate the TS2
and TS2-B units.
Read all safety messages in the IMPORTA T SAFETY
I FORMATIO section before operating this equipment.
1. Plug unit into a properly grounded electrical receptacle of
the correct voltage, size, and plug configuration. Refer to
the SPECIFICATIONS section in this manual for details.
2. Move the POWER On/Off (I/O) switch to the On (I) position.
BUR HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
3. Turn the thermostat control to the desired temperature
setting.
4. Allow the unit 30 minutes to reach operating temperature.
WARNING
CAUTION
Thermostat
Control
Power On/Off
Switch
Figure 12. Control Panel — TS2 Model
Thermostat
Control
POWER On/Off (I/O)
Switch
Figure 13. Control Panel — TS2-B Models

MAI TE A CE
Form No. TS2M-0210 11
General
Merco Thermal Shelves are designed for maximum durability
and performance with minimum maintenance.
ELECTRIC SHOCK HAZARD:
• Turn power switch OFF, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO OT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Use only OEM Replacement Parts when service is
required. Failure to use OEM Replacement Parts will
void all warranties and may subject operators of the
equipment to hazardous electrical voltage, resulting in
electrical shock or burn. OEM Replacement Parts are
specified to operate safely in the environments in
which they are used. Some aftermarket or generic
replacement parts do not have the characteristics that
will allow them to operate safely in Merco equipment.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact a Factory Authorized Service
Agent or contact the Merco Service Department at
800-506-9565.
WARNING
Cleaning
To preserve the finish of the Merco Thermal Shelf, it is
recommended that all surfaces be cleaned daily
Use non-abrasive cleaners only. Abrasive cleaners could
scratch the finish of the unit, marring its appearance and
making it susceptible to soil accumulation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and wash all food pans, if necessary.
3. Wipe down all metal surfaces with a clean, damp cloth.
Stubborn stains may be removed with a good stainless steel
or non-abrasive cleaner. Clean hard to reach areas using a
small brush and mild soap.
NOTICE

TROUBLESHOOTI G GUIDE
12 Form No. TS2M-0210
Unit too hot.
Unit not hot enough.
Unit not working at all.
Thermostat control set too high.
Thermostat control stuck in the “on”
position.
Unit plugged into an incorrect power
supply.
Thermostat control set too low.
Location of unit is susceptible to air
currents (air conditioning ducts or
exhaust fans).
Unit not plugged in.
Unit not turned on.
Power On/Off (I/O) switch is not
functioning.
Heating element is burned out.
Thermostat control is defective.
Move Power On/Off (I/O) switch to the On (I)
position.
Contact Factory Authorized Service Agent or
Merco for assistance.
Contact Factory Authorized Service Agent or
Merco for assistance.
Contact Factory Authorized Service Agent or
Merco for assistance.
Plug unit into proper power supply.
Adjust thermostat control to a higher setting.
Block air currents or relocate unit.
Adjust thermostat control to a lower setting.
Contact Factory Authorized Service Agent or
Merco for assistance.
Verify with qualified personnel that power supply
matches unit specification.
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn the power switch OFF,
unplug the power cord, and allow the unit to cool before
performing any maintenance or cleaning.
WARNING
Symptom Probable Cause Corrective Action

OPTIO S A D ACCESSORIES
Form No. TS2M-0210 13
4″ (102 mm) Adjustable Legs (TS2 Models)
Use the following procedure to install 4″ adjustable legs on a
TS2 model.
NOTE: 4″ (102 mm) legs are standard on models 42″
(1067 mm) and wider.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
2. Carefully turn the unit upside down and lay the unit on a flat
surface. Make sure to cover the surface with something to
prevent scratching the unit.
3. At each corner, thread a 4″ leg into the bottom of the unit.
Hand-tighten until snug. Do not over-tighten.
4. Return the unit to the upright position.
NOTICE
Figure 14. Leg Installation
NOTE: The feet on the 4″ legs are adjusta le for leveling the
unit. Use a 9/16″ (14 mm) open-end wrench to make
leveling adjustments once the unit is placed in its final
position.
4″ (102 mm)
Leg
Lengthen
Shorten
Adjustable Foot

Printed in U.S.A. February 2010 Part No. 07.04.497.00 Form No. TS2M-0210
MERCO LIMITED WARRA TY
1. PRODUCT WARRA TY
Merco LLC (“Merco”), warrants the products that it
manufactures (the “Products”) to be free from defects in
materials and workmanship, under normal use and service, for
a period of one (1) year from the date of purchase when
installed and maintained in accordance with Merco’s written
instructions or 18 months from the date of shipment from
Merco. Buyer must establish the Product’s purchase date by
returning Merco’s Warranty Registration Card or by other
means satisfactory to Merco in its sole discretion.
Merco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One
(1) Additional Year Parts-Only Warranty:
Heated Drawer Elements (metal sheathed)
Heated Drawer Rollers and Slides
Convenience Merchandiser Elements (metal sheathed)
Heated Merchandising Cabinet Elements
(metal sheathed air heating)
b) inety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT.
Without limiting the generality of the foregoing, SUCH
WARRANTIES DO NOT COVER: Coated incandescent light
bulbs, fluorescent lights, decorative heat lamp bulbs, glass
components, and fuses; Product failure in water heating
equipment caused by liming, sediment buildup, chemical attack,
or freezing; or Product misuse, tampering or misapplication,
improper installation, or application of improper voltage.
2. LIMITATIO OF REMEDIES A D DAMAGES
Merco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Merco’s option, to repair or replacement
using new or refurbished parts or Product by Merco or a factory
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United ingdom, or
Australia, in which case Merco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Merco reserves
the right to accept or reject any such claim in whole or in part.
In the context of this Limited Warranty, “refurbished” means a
part or Product that has been returned to its original
specifications by Merco or a factory authorized service agency.
Merco will not accept the return of any Product without prior
written approval from Merco, and all such approved returns
shall be made at Buyer’s sole expense. MERCO WILL NOT BE
LIABLE, UNDER ANY CIRCUMSTANCES, FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING
BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS
RESULTING FROM THE USE OF OR INABILITY TO USE THE
PRODUCTS OR FROM THE PRODUCTS BEING
INCORPORATED IN OR BECOMING A COMPONENT OF
ANY OTHER PRODUCT OR GOODS.
Merco, LLC
1111 North Hadley Road
Fort Wayne, Indiana 46804 USA
Technical Support: 800.506.9565
Customer Service: 888.417.5462
www.mercoproducts.com