Meyer Sound USM-1 User manual

USM-1
Features
High gain-before-feedback
Wide horizontal coverage
Flat frequency response
Rugged and reliable
Applications
Stage monitoring
Live music clubs
Touring reinforcement
— 12
–
–
— 9
–
–
— 6
–
–
— 3
–
–
— 0
Inches
The USM-1 is a high-powered, wide-
coverage loudspeaker for professional
stage monitoring applications. Specifi-
cally designed for touring reinforce-
ment, the accurate, rugged USM-1 is
a biamplified system consisting of a
proprietary 15-inch low-frequency driver
in a vented enclosure, and a 70-degree
high-frequency horn with 2-inch (throat
diameter) driver.
The USM-1’s drivers provide excep-
tional efficiency and power handling,
with low distortion for maximum clar-
ity. Its very flat frequency response
allows control of feedback at high
stage levels.
The sturdy, multi-ply hardwood
enclosure with textured finish is
designed to withstand road abuse. The
USM-1 comes with handles and, option-
ally, aircraft-style rigging pan fittings.
The USM-1 requires a high-quality
professional stereo power amplifierca-
pable of delivering up to 600 watts per
channel continuously into 8 ohms, with
a signal voltage gain of 10␣dB (mini-
mum) to 30␣dB (maximum).
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, CA 94702
[phone]
FAX [phone]
High Power
Stage Monitor

Acoustical – USM-1/S-1 System
Frequency Response
1
40-18k Hz +4 dB
Maximum SPL
2
Continuous 130 dB
Peak 139 dB
Maximum Peak (Music Signal) 144 dB
HF Coverage, -6dB points 70°horizontal x 60°vertical
Acoustical Crossover Frequency 900 Hz
USM-1 Loudspeaker
Transducers
Low Frequency MS-15 15-inch cone driver, 12 ohms
High Frequency MS-2001A 2-inch throat compression driver, 8 ohms
High Frequency Horn 70 degree modified radial
HF Network DC blocking capacitor
Enclosure 2.3 cu. ft. vented, multi-ply Finnish birch
Finish Black textured
Protective Grill Hex perforated metal, powder coated, charcoal-
grey foam covering
Connector EP-4 male, EP-5 male (Europe only)
Rigging (optional) Aircraft pan fittings or
3
⁄8"-16 or M10 x 1.5 nut plates
Physical Dimensions 21" W x 24
1
⁄4" H x 18
1
⁄4" D
Weight 82 lbs. (37.3 kg)
S-1 Control Electronics Unit
Input Type
3
Active balanced ISO™ input, 10k ohms, 5k ohms per leg
Output Type Active push-pull, will drive 600 ohms
Maximum Input/Output Level
Balanced +26 dBu
Unbalanced +20 dBu
Hum and Noise
4
-90 dBV
Dynamic Range >110 dB
Sense Inputs 100k ohms true differential
Low-Frequency Delay Type Active all-pass
Driver Protection Circuitry
Low Frequency RMS limiter and excursion limiter
High Frequency RMS limiter and excursion limiter
VHF Peak limiter
Indicators
Sense/Gain Detect, Hi and Lo Green/Red LEDs
Limit, Hi, Lo, and VHF Red LEDs
Safe Green LED
Power Supply Green/Red LED
Controls
Front Panel Input attenuator, AC power switch
Preset Panel Lo Cut switch, Safe switch, VHF switch, VHF control
Connectors
Balanced Inputs/Outputs 3-pin XLR (A-3)
Sense Inputs Banana jacks
Power 90-105/180-250 VAC, 50/60 Hz (rear-panel switchable)
Physical Dimensions 19" W x 1
3
⁄4" H x 7
3
⁄4" D standard rack mount
Weight 8 lbs. (3.6 kg)
USM-1 Specifications
Note 1:
Measured 1 meter on-axis to
high horn, half-space con–
ditions, pink noise input, in
third-octave bands.
Note 2:
Loudspeaker driven with “A”
weighted noise (peak-to-RMS
ratio
≈ 12 dB), with amplifier
rated at 600 W/channel at
8␣ohms. The USM-1 will accom-
modate amplifiers capable of
output levels up to
± 140 vpk.
Note 3:
ISO™ input: Pins 1, 2 and 3 are
transformer isolated, shell is
connected to chassis/AC
mains ground.
Note 4:
“A”- weighted, unbalanced.

The S-1 Control
Electronics Unit
The USM-1 operates as a system with the
S-1 Control Electronics Unit (one per chan-
nel). A single-channel device operating at
line level, the S-1 is the final component in
the signal chain before the amplifier.
Optimized for the USM-1 loudspeaker
and pre-aligned at the factory, the S-1
contains frequency and phase response
alignment circuitry, and Meyer Sound’s
exclusive SpeakerSense ™ driver protection
circuitry, incorporating both peak and RMS
signal limiting as well as excursion protec-
tion.
SpeakerSense driver protection circuitry
protects the USM-1 loudspeaker compo-
nents from damage due to overheating or
excessive excursion under high power con-
ditions. This unique circuit continuously
monitors the power applied to the USM-1
drivers, and individually limits the high-
frequency and low-frequency outputs when
the safe operating limits of the drivers are
exceeded. Until the onset of overload, the
SpeakerSense circuitry has no effect on the
signal.
The S-1 SpeakerSense circuit incorpo-
rates Meyer Sound’s new MultiSense™
function, which allows the use of multiple
power amplifiers having different channel
gains and/or power ratings. The S-1 accom-
modates two stereo power amplifiers, and
provides separate Sense inputs for each. Its
MultiSense circuit, which implements an
analog OR condition, automatically tracks
the power amplifier with the greatest out-
put voltage swing to control the system
protection limiters.
To enhance the effectiveness of the
USM-1 in stage monitoring applications,
the S-1 incorporates sliding filters which
band-limit the system response under full-
power conditions. This has the effect of dis-
criminating for vocal information in the
signal to increase clarity.
Also provided is a switch-selectable Safe
function, which widens the safety margin of
the system and is intended to be used when
extended periods of overload are antici-
pated. The Safe switch and other setup con-
trols are located behind a cover plate on the
S-1 front panel, providing a means of se-
curing the system installer’s presets.
UltraSeries™ S-1 Power
Sense Limit
Safe
Adj
Lo Cut
Cal
VHF
Var
Safe
∞
20
10 843
2
1
0
Attn dB
5
6
-
Lo
Hi
VHF

Architectural and
Engineering Specifications USM-1/S-1
The speaker system, its companion
Control Electronics Unit, and a power
amplifier rated at 600 watts/channel into
8␣ohms shall meet the following perform-
ance criteria: frequency response, 40 Hz to
18 kHz plus or minus 4 dB measured with
1
/ 3
rd
octave pink noise at 1 meter on axis;
output of 130 dB SPL one meter on axis
with peaks of 139 dB SPL when driven with
“A”-weighted noise. High frequency dis-
tribution pattern, 70 degrees horizontal by
60 degrees vertical.
Speaker enclosure dimensions are
21" W x 24
1
⁄ 4 " H x 18
1
⁄ 4 " D, weight 82 lbs
(37.3 kg).
Control Electronics Unit dimensions are
19" W x 1
3
⁄ 4 " H 7
3
⁄ 4
" D, weight 8 lbs (3.6␣kg).
The speaker system shall be the Meyer
Sound USM-1.
The Control Electronics Unit shall be
the Meyer Sound S-1.
The compact speaker system shall be of
the two-way type, with a 15" low-frequency
loudspeaker front-mounted in a ducted
bass-reflex hardwood plywood enclosure,
a compression driver mounted on a high-
frequency horn which has a 2.0" throat and
4" diameter diaphragm with gap field of
strength of 19k Gauss, and a separate Con-
trol Electronics Unit.
The Control Electronics Unit shall con-
tain a power supply capable of operating
from a 90-125/180-250 VAC, 50/60 Hz line;
electronic crossover circuitry; electronic
delay for the phase alignment of the low-
frequency speaker; low- and high-frequency
protection filters which automatically acti-
vate under high power conditions;
RMS, peak and excursion limiters to pro-
tect the speaker components; equalization
circuitry; active balanced input; and indica-
tor LEDs for power and limiters. Total har-
monic distortion shall be less than 0.1%.
“A”- weighted noise level shall be at least
110 dB below maximum rated output of
+26 dBu.
Sound
engineering
for the art
and science
of sound.
Meyer Sound Laboratories, Inc.
2832 San Pablo Avenue
Berkeley, CA 94702
[phone]
FAX [phone]
Meyer Sound Laboratories has
devoted itself to designing,
manufacturing, and refining com-
ponents that deliver superb sonic
reproduction. Every part of every
component is designed and built to
exacting specifications and
undergoes rigorous, comprehensive
testing in the laboratories.
Research remains an integral,
driving force behind all production.
Meyer strives for sound quality that
is predictable and neutral over an
extended lifetime and across an
extended range.
Physical Dimensions
10.50
24.25
21.00
±.13
10.13 CG
7.25
21.04
31.47
45°
7.00
2.62
6.50 ±.13
3.50
13.00
18.25
20.25
2.00
(GRILL FRAME
W/FOAM)
2.62
2..25
9.50
2..25
©1994 Meyer Sound 04.151.014.01 B2