Mi-T-M MV-900-OMEV User manual

Wet/Dry Vac Operator's Manual 1
OPERATING INSTRUCTIONS FOR
WET/DRY VACS
MV-900-0MEV
©Copyright 2005, Mi-T-M Corporation®Form #37-0751-E/F/S-061109
CAUTION
RISK OF INJURY!
READ MANUAL BEFORE OPERATING!
This manual is an important part of the Wet/Dry Vac and must
remain with the unit when you sell or rent it!
®
C US
201473

2 Wet/Dry Vac Operator's Manual
TABLE OF CONTENTS
INTRODUCTION.......................................................................................................................3
IMPORTANT SAFETY WARNINGS...................................................................................... 4-5
RISK OF ELECTRIC SHOCK OR ELECTROCUTION.................................................4
RISK OF EXPLOSION OR FIRE ..................................................................................5
RISK OF BODILY INJURY............................................................................................5
FEATURES ...............................................................................................................................6
INSTALLATION & PREPARATION ..........................................................................................7
START-UP.....................................................................................................................7
GROUNDING INSTRUCTIONS....................................................................................8
OPERATING INSTRUCTIONS .................................................................................................9
OPERATION .................................................................................................................9
SHUTDOWN.................................................................................................................9
TROUBLESHOOTING............................................................................................................10
SPECIFICATIONS...................................................................................................................10
STATEMENT OF WARRANTY ...............................................................................................11
PARTS LIST...................................................................................................................... 12-16
ASSEMBLY FOR MV-900-0MEV................................................................................12
VACUUM POWER HEAD ASSEMBLY (3-0239).........................................................14
WIRING DIAGRAM.....................................................................................................16
NOTES ....................................................................................................................................17
FRENCH............................................................................................................................ 18-33
SPANISH........................................................................................................................... 34-51

Wet/Dry Vac Operator's Manual 3
INTRODUCTION
Congratulations on the purchase of your new commercial Mi-T-M Wet/Dry Vac! You can be assured your Mi-T-M Wet/Dry
Vac was constructed and designed with quality and performance in mind. Each component has been rigorously tested
to ensure the highest level of acceptance.
This operator's manual was compiled for your benet. By reading and following the simple safety, installation, operation,
maintenance and troubleshooting steps described in this manual, you will receive years of trouble free operation from your
new Mi-T-M Wet/Dry Vac. The contents of this manual are based on the latest product information available at the time
of publication. The manufacturer reserves the right to make changes in price, color, materials, equipment, specications
or models at any time without notice.
! IMPORTANT !
The following "Signal Words" are used throughout this manual to designate the degree or
level of hazard seriousness.
DANGER:Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
WARNING:Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
CAUTION:Indicates a potentially hazardous situation which, if not avoided
MAY result in minor or moderate injury.
The symbol set to the left of this paragraph is a "Safety Alert Symbol". This symbol is used
to call attention to items or procedures that could be dangerous to you or other persons
using this equipment.
ALWAYS PROVIDE A COPY OF THIS MANUAL TO ANYONE USING THIS EQUIPMENT. READ
ALL INSTRUCTIONS BEFORE OPERATING THIS WET/DRY VAC AND ESPECIALLY POINT
OUT THE "SAFETY WARNINGS" TO PREVENT THE POSSIBILITY OF PERSONAL INJURY
TO THE OPERATOR.
Once the unit has been removed from the box, immediately write in the serial number of your unit in the space provided
below.
SERIAL NUMBER_________________________________
Inspect for signs of obvious or concealed freight damage. If damage does exist, le a claim with the transportation
company immediately. Be sure that all damaged parts are replaced an that the mechanical and electrical problems are
corrected prior to operation of the unit. If you require service, contact your Customer Service.
CUSTOMER SERVICE
CALL OUR TOLL-FREE NUMBER
for the Sales or Service Center nearest you!
800-553-9053
Please have the following information available for all service calls:
1. Model Number
2. Serial Number
3. Date and Place of Purchase

4 Wet/Dry Vac Operator's Manual
SAFETY WARNINGS
WARNING: When using this product, basic precautions should always be observed, including the following:
READ ALL SAFETY INSTRUCTIONS BEFORE USING WET/DRY VAC
POTENTIAL CONSEQUENCE PREVENTION
Serious injury or death could occur
if the Wet/Dry Vac is not properly
grounded. Your Wet/Dry Vac is
powered by electricity and may
causeelectricshockorelectrocution
if not used properly.
This product must be grounded. Connect to a
properly grounded outlet only. See "Grounding
Instructions".
Always be certain the unit is receiving proper
voltage. Beforeplugging the unitintoacompatible
power source, be certain the switch is in the "OFF"
position. Disconnect when not in use.
Do not modify plug provided with the product. If it
will not t the outlet, have a proper outlet installed
by a qualied electrician. Do not remove the plug
or use any type of adapter.
DonotexposetheWet/DryVactorainorsubmerge
in water. Do not use pressurized water to clean
the Wet/Dry Vac. Store indoors.
Check power cord for signs of crushing, cutting
or heat damage. If replacement of plug or cord is
needed, use only identical replacement parts.
If Wet/Dry Vac is not working correctly, has been
dropped, damaged, left outdoors, or dropped into
water, return it to a service center.
Keep all connections dry and off the ground. Do
not allow electrical cords to lay in water or in such
a position where water could come in contact
with them. Do not handle plug or Wet/Dry Vac
with wet hands.
Do not pull or carry the unit by the electrical cord.
Do not use the cord as a handle, close a door on
cord, or pull cord around sharp edges or corners.
Do not run Wet/Dry Vac over cord. Keep cord
away from heated surfaces.
Turn off all controls before unplugging the unit
from the outlet. Do not unplug by pulling on cord.
To unplug, grasp the plug, not the cord.
Use only extension cords having an electrical
rating not less than the rating of the product. Do
not use damaged extension cords. Examine
extension cord before using and replace if
damaged. Keep cord away from heat and
sharp edges. Always connect and disconnect
the extension cord from the receptacle before
connecting and disconnecting the product from
the extension cord.
Any electrical wiring or repairs performed on this
Wet/DryVacshouldbedonebyAuthorizedService
Personnel in accordance with National and Local
electrical codes.
Before opening any electrical enclosure, always
shut off the Wet/Dry Vac and unplug the Wet/Dry
Vac from the power source. AllowtheWet/DryVac
to cool down. Service in a clean, dry, at area.
RISK OF
ELECTRIC SHOCK
OR
ELECTROCUTION
Serious injury or death may occur if
electrical repairs are attempted by
unqualied persons.
Electrical shock may occur from
electrical cord.
HAZARD

Wet/Dry Vac Operator's Manual 5
POTENTIAL CONSEQUENCE PREVENTION
SAFETY WARNINGS
READ ALL SAFETY INSTRUCTIONS BEFORE USING WET/DRY VAC
RISK OF
EXPLOSION OR FIRE
Serious injury or death may occur
from normal sparks in the motor.
Serious injury or death may occur
from absorption of flammable
materials.
Injury may occur from unit
overheating.
AlwaysoperateWet/DryVacin awellventilated
area free of ammable vapors, combustible
dust, gases or other combustible materials.
Do not pick up any ammable materials such as
gasoline or anything that is burning or smoking
such as cigarettes, ashes, etc.
Always unrollthePowerCordbeforeoperating.
Using a rolled-up power cord could result in
low voltage or overheating.
Do not use without dust lter in place.
HAZARD
RISK OF BODILY INJURY Injury may occur from the Wet/Dry
Vac. Keep the suction nozzle away from the body,
especially the eyes, ears, nose and mouth.
Do not use this unit to pickup endangering
dusts or substances.
Stay alert-watch what you are doing. Do not
operate the unit when fatigued or under the
inuence of alcohol or drugs.
Wet surfaces can be slippery, wear protective
foot gear and keep good footing and balance
at all times.
Direct supervision is necessary when children
operate this Wet/Dry Vac. Do not allow to be
used as a toy.
DO NOT leave operating unit unattended.
Shut off the Wet/Dry Vac and disconnect from
the power source before leaving.
Know how to stop the Wet/Dry Vac. Be
thoroughly familiar with controls.
Before servicing the unit: turn the unit off and
allow the unit to cool down. Service in clean,
dry, at area. Block the wheels to prevent the
unit from moving.
Use of this machine for anything not specied
in this manual may be dangerous and must
be avoided. The manufacturer cannot be held
responsible for any damage/injury caused to
persons or property because of the incorrect
use of the machine due to procedures being
used which are not specied in this manual.
SAVE THESE INSTRUCTIONS
Do not put any object into openings. Do not use
withanyopening blocked;keepfree of dust,lint,
hair, and anything that may reduce air ow.
Keep hair, loose clothing, ngers, and all parts
of body away from openings.
Use only as described in this manual. Use only
manufacturer's recommended attachments.
Use extra care when cleaning on stairs.

6 Wet/Dry Vac Operator's Manual
FEATURES LISTING
1. 25' Power Cord
2. Vacuum Power Head Assembly
3. On/Off Switch
4. Filter
5. Latch
6. Bottom Canister
7. Vacuum Inlet
8. Suction Hose w/ Inlet Cuff
9. Squeegee Tool- 12"
10. Curved Plastic Wand
11. Crevice Tool
12. Aluminum/Plastic Wand
13. Combo Floor Tool- 12"
14. Paper Bag
WET/DRY VAC FEATURES
MV-900-0MEV FEATURES-022103-BAR

Wet/Dry Vac Operator's Manual 7
START-UP:
1. Proper attire is essential to your safety. It is advised to utilize whatever means
necessary to protect eyes, ears, and skin.
2. Remove the Canister Lid by releasing the Side Latches.
a. Inspect the Wet/Dry Filter to ensure it is free of obstructions. Clean or replace
if necessary.
b. Inspect the Canister to ensure it is empty and free of obstructions.
c. If repairs are needed, contact your Authorized Service Center and replace
with only genuine manufacturer replacement parts.
3. Filter bags are not necessary with your Mi-T-M Wet/Dry Vac. If desired, you
may attach a Paper Filter Bag (supplied with the unit) onto the Suction Intake of
the Canister for collection and immediate disposal of dry debris. Be certain the
paper lter bag is removed for wet pickup. Ensure all materials are disposed
of according to State and Federal EPA Standards.
4. Replace the Canister Lid and securely tighten the Side Latches.
5. Securely insert the larger end of the Flexible Hose sleeve into the Suction
Intake.
6. Connect the Extension Wand onto the Flexible Hose.
7. Connect the Wet/Dry Floor Tool onto the Extension Wand.
8. Ensure electrical supply is identical to the specications listed on your Wet/Dry
Vac Data Plate.
9. Ensure the On/Off Switch is in the "OFF" position.
10. Insert the grounded plug of the Power Cord into a grounded receptacle.
INSTALLATION & PREPARATION
WARNING
Where ammable gas vapors
maybepresent. An electrical
spark from the motor may
cause a re.
RISK OF FIRE!
WARNING
Where the unit may be
exposed to rain, snow or
immersed in water. Water
may inltrate the electrical
system causing an
electrical hazard.
RISK OF ELECTRIC SHOCK!

8 Wet/Dry Vac Operator's Manual
GROUNDING INSTRUCTIONS:
1. This Wet/Dry Vac must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This Wet/Dry Vac is equipped with a cord having an
equipment-grounding conductor and grounding plug. The plug must be inserted
into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Check with a qualied electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Do not modify the plug provided with
the appliance- if it will not t the outlet, have a proper outlet installed by a
qualied electrician.
2. This Wet/Dry Vac is for use on a nominal 120-volt circuit and has a grounding
attachment plug (See Fig. A). Make sure that the Wet/Dry Vac is connected
to an outlet having the same conguration as the plug. No adapter should be
used with this Wet/Dry Vac.
3. Unroll the Power Cord before plugging it into a grounded outlet.
NOTE: The Wet/Dry Vac is supplied with a Tank Drain, be sure the Drain Cap is
covering the Tank Drain opening before starting the unit. The Wet/Dry
Vac will not operate properly with the Tank Drain open.
INSTALLATION & PREPARATION
GROUNDING
PIN
GROUNDED
OUTLET
RISK OF ELECTRIC SHOCK!
WARNING
Improper connection of
the equipment-grounding
conductor can result in a
risk of electric shock.
WARNING
If use of an extension
cord is required, use only
extension cords having
an electrical rating not
less than the rating of
the product. Do not use
damaged extension cords.
RISK OF ELECTROCUTION!
CAUTION
A wound-up power cord
may result in low voltage
and possible overheating
causing a re.
RISK OF FIRE!
FIG. A

Wet/Dry Vac Operator's Manual 9
OPERATION:
1. Please observe the following precautions while using the Wet/Dry Vac.
a. Do not place any object in the Wet/Dry Vac openings. Ensure all
openings remain unobstructed and free of lint, hair, dust or
anything which may reduce air ow.
b. Aggressive solvents or detergents should not be used. DO
NOT operate the unit if you see any foam/liquid leaking from the
machine.DONOTresumeoperationuntiltheunithasbeeninspected
and repaired by a qualied service person.
c. If the equipment should overturn, it is recommended that the Wet/
Dry Vac be placed upright before turning it off.
2. While holding the Flexible Hose, move the On/Off Switch to the "ON"
position.
3. Move the Wet/Dry Floor Tool slowly across the surface you wish to clean.
4. Wet Pickup Application:
a. As the Canister lls, the oat will begin to rise. The function of the
oat is to stop suction when the tank is full or if the Wet/Dry Vac
should accidently overturn. When the Canister is full, turn the
On/Off Switch to the "OFF" position and disconnect the Power Cord
from the receptacle.
b. Remove the Canister Lid and empty any debris from the
Canister.
5. Dry Pickup Application:
a. If using a paper lter bag, remove and replace with a new paper
lter bag.
b. If not using a paper lter bag, tilt the Wet/Dry Vac to empty the
Canister.
NOTE: Ensure all materials are disposed of according to State and Federal
EPA Standards.
6. Replace the Canister Lid and plug the Power Cord back into the grounded
outlet.
7. Turn the On/Off Switch to "ON" to resume operation.
SHUTDOWN:
1. When cleaning application is completed, turn the On/Off Switch to the "OFF"
position.
2. Disconnect the Power Cord from the receptacle.
3. Roll up the disconnected Power Cord and place it on the designated area
of the Wet/Dry Vac.
4. Remove the Canister Lid and empty the Canister.
5. Rinse the Canister and allow to air dry.
6. Pull the Wet/Dry Filter off of the Canister Lid.
a. Wet-Filter Cleaning: Rinse with warm water and shake clean. Allow to
air dry completely.
b. Dry-Filter Cleaning: Shake lter clean. Occasionally rinse with warm
water. Allow to air dry completely.
7. Place the dry lter back onto the Canister Lid.
8. Wipe down the exterior of the Wet/Dry Vac and store indoors.
OPERATING INSTRUCTIONS
WARNING
Do not yank on any cord to
disconnect.
RISK OF ELECTROCUTION!

10 Wet/Dry Vac Operator's Manual
TROUBLESHOOTING
SYMPTOM PROBABLE CAUSE REMEDY
Wet/Dry Vac will not start. Power Cord is disconnected. Ensure Power Cord is securely
connected to the unit and to the
power source. If using an
extension cord, ensure the power
cord and extension cord are
securely connected.
Circuit overload. Check breaker or fuse panel.
Brushes on motor are worn. Contact your Customer Service.
Inadequate suction. Flexible Hose is obstructed, cut or Clean or replace Flexible Hose.
damaged.
Wand or attachment is obstructed. Clear obstruction.
Wet/Dry Filter is full of dirt. Clean or replace.
No suction. Canister is full. Empty Canister.
SPECIFICATIONS
TECHNICAL DATA MODEL NO. MV-900-0MEV
MOTOR 120V 2-Stage By-pass
HP 1.3 Nominal HP
CFM 101
WATERLIFT (Inches) 87
CAPACITY (Gallons) 9
WATER RECOVERY (Gallons) 6.0
ELECTRICAL CORD 25'
DIMENSIONS (L x W x H / Inches) 14 x 14 x 22
WEIGHT 25

Wet/Dry Vac Operator's Manual 11
STATEMENT OF WARRANTY
FOR Mi-T-M WET/DRY VACUUM
MV-900-0MEV
Manufacturer warrants all parts (except those referred to below) of your new Wet/Dry Vac to be free from
defects in materials and workmanship for Two (2) Year Limited from the date of original purchase with the
following exception:
Lifetime warranty on canister.
Defective parts will be repaired or replaced at our option during the warranty period. In any event, reimbursement
is limited to the purchase price paid.
EXCLUSIONS
1. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, operation at other
than recommended speeds or temperature. Parts damaged or worn because of the use of caustic liquids
or by operation in abrasive or corrosive environments are not warranted. Failure to follow recommended
operating and maintenance procedures also voids warranty.
2. The use of other than Genuine Manufacturer Repair Parts will void warranty. Parts returned, prepaid to
our factory or to an Authorized Service Center will be inspected and replaced free of charge if found to be
defective and subject to warranty. There are no warranties which extend beyond the description of the
face hereof. Under no circumstances shall the manufacturer bear any responsibility for loss of use of the
unit, loss of time or rental, inconvenience, commercial loss or consequential damages.
For Service or Warranty Consideration, contact
Mi-T-M Corporation®, 8650 Enterprise Drive, Peosta, IA 52068-0050
1-563-556-4784 / 1-800-553-953 / Fax [phone]
Monday - Friday 8:00 a.m. - 5:00 p.m. CST

12 Wet/Dry Vac Operator's Manual
ASSEMBLY FOR MV-900-0MEV
MV-900-0MEV-071907-JJT

Wet/Dry Vac Operator's Manual 13
MV-900-0MEV-071907-JJT
ASSEMBLY FOR MV-900-0MEV
REF. # DESCRIPTION PART # QTY.
1 Decal- Data Plate N/A 1
2 Vacuum Power Head Assembly 3-0239 1
3 Decal- Mi-T-M Logo 34-1412 1
4 Decal- Mi-T-M Stripe 34-1413 1
5 Hex Nut 30-0053 4
6 Canister Bottom 62-0147 1
7 Latch 33-0416 2
8 Screw 27-8942 4
9 Caster Wheel w/Plate 14-0093 4
10 Screw 27-3262 12
11 Vacuum Inlet Kit (Inc. 11-15) 70-0368 1
12 Screw (See 70-0368) N/A Sep. 4
13 Receiver Flange (See 70-0368) N/A Sep. 1
14 Deflector Elbow (See 70-0368) N/A Sep. 1
15 Inlet Flange Gasket (See 70-0368) N/A Sep. 1
16 Receiver Hose (See 70-0368) N/A Sep. 1
17 Combo Floor Tool- 12" 33-0411 1
18 Squeegee Tool- 12" 33-0410 1
19 Crevice Tool 33-0412 1
20 Curved Wand 16-0403 1
21 Wand 16-0402 2
22 Paper Bag 19-0222 1
23 Suction Hose w/ Inlet Cuff 15-0241 1

14 Wet/Dry Vac Operator's Manual
VACUUM POWER HEAD ASSEMBLY (3-0239)
3-0239-012304-BAR

Wet/Dry Vac Operator's Manual 15
3-0239-012304-BAR
VACUUM POWER HEAD ASSEMBLY (3-0239)
REF. # DESCRIPTION PART # QTY.
1 Top Canister 62-0151 1
2 Rocker Switch 32-0789 1
3 Screw 27-9552 3
4 Screw 27-9553 2
5 Handle Base 62-0157 1
6 Screw 27-9555 8
7 Handle 62-0158 1
8 Strain Relief 32-0788 1
9 Cord Assembly 32-0792 1
10 Screw 27-9551 8
11 Cord Clamp 32-0787 1
12 Terminal Block 32-0790 1
13 Screw 27-9554 6
14 Chamber Divider 62-0152 1
15 Gasket Filter 26-0275 1
16 Motor Retainer Top 62-0153 1
17 Motor Retaining Head Bottom 62-0154 1
18 Motor Bottom Gasket 26-0277 1
19 Motor Gasket 26-0224 2
20 Motor- 1.3 HP 2-0140 1
21 Canister Base 62-0155 1
22 Filter Housing Spacer 62-0156 4
23 Screw 27-9556 4
24 Screen 19-0229 1
25 Float 62-0161 1
26 Filter Housing 62-0159 1
27 Filter 19-0221 1
28 Filter Retaining Clip 62-0160 1

16 Wet/Dry Vac Operator's Manual
WIRING DIAGRAM
MV-900 WIRING DIAGRAM-030303-KZ

Wet/Dry Vac Operator's Manual 17
NOTES

18 Manuel opérateur d'aspirateur eau/poussière
TABLE DES MATIERES
INTRODUCTION.....................................................................................................................19
INSTRUCTIONS IMPORTANTES DE SÉCURITÉ ........................................................... 20-21
RISQUE DE DÉCHARGE ÉLECTRIQUE OU D'ÉLECTROCUTION .........................20
RISQUE D'EXPLOSION OU D'INCENDIE .................................................................21
RISQUE DE BLESSURES CORPORELLES..............................................................21
CARACTÉRISTIQUES ...........................................................................................................22
INSTALLATION & PRÉPARATION .................................................................................. 23-24
MISE EN MARCHE.....................................................................................................23
INSTRUCTIONS POUR LA MISE A LA TERRE .........................................................24
CONSIGNES D'UTILISATION ................................................................................................25
FONCTIONNEMENT..................................................................................................25
ARRÊT........................................................................................................................25
DÉPANNAGE..........................................................................................................................26
SPÉCIFICATIONS...................................................................................................................26
BON DE DE GARANTIE ......................................................................................................27
LISTE DES PIÈCES......................................................................................................... 28-32
ASSEMBLÉE POUR MV-900-0MEV ..........................................................................28
ASSEMBLÉE POUR TÊTE DE PUISSANCEDE VIDE (3-0239) ...............................30
DIAGRAMME DE CÂBLAGE .....................................................................................32
NOTE ....................................................................................................................................33

19 Manuel opérateur d'aspirateur eau/poussière
INTRODUCTION
Félicitations de l’achat de votre nouveau aspirateur eau/poussière industriel Mi-T-M! Vous pouvez être assuré que
votre nouveau aspirateur eau/poussière a été construit et conçu avec qualité et performance à l’esprit. Chaque
composant a été rigoureusement testé an d’atteindre le plus haut niveau de abilité.
Le manuel de l’utilisateur a été dressé pour que vous en retiriez le meilleur parti. Par la lecture et l'application des
mesures simples de sécurité, d’installation, d'opération, d’entretien et de dépannage décrites dans ce manuel, votre
nouveau aspirateur eau/poussière Mi-T-M fonctionnera sans faille pendant de nombreuses années. Le contenu de ce
manuel est basé sur la dernière information disponible du produit au moment de la publication. Mi-T-M se réserve le
droit d’effectuer des changements de prix, de couleur, de matériaux, d’équipement, de caractéristiques ou de modèles
à tout moment sans préavis.
! IMPORTANT !
Les "mots d'alerte" suivants sont utilisés à travers ce manuel pour indiquer le degré ou le niveau de gravité du
danger.
DANGER:Indique une situation au danger imminent qui, si elle n’est pas
évitée, ENTRAINERA la mort ou des blessures graves.
AVERTISSEMENT:Indique une situation potentiellement dangereuse
qui, si elle n’est pas évitée, POURRAIT entraîner la mort ou des
blessures graves.
ATTENTION:Indique une situation potentiellement dangereuse, qui, si elle n'est
évitée, PEUT entraîner des dommages corporels mineurs ou
modérés.
Le symbole placé à gauche de ce paragraphe est un "symbole d'alerte de sécurité". Ce
symbole est utilisé pour souligner les points ou les procédures qui pourraient être dangereux
pour vous ou tout autre personne utilisant cet équipement.
FOURNISSEZ TOUJOURS UNE COPIE DE CE MANUELA TOUTE PERSONNE UTILISANT CET
EQUIPEMENT. LISEZ TOUTES LES INSTRUCTIONS AVANT D'UTILISER CET ASPIRATEUR
EAU/POUSSIERE ET ATTIREZ SPECIALEMENT L'ATTENTION AUX "AVERTISSEMENT DE
SÉCURITÉ" POUR EMPECHER LA POSSIBILITÉDE BLESSURES POUR L'UTILISATEUR.
Une fois l'appareil déballé, écrivez immédiatement le numéro de série de votre appareil dans l'espace ci-dessous
NUMERO DE SÉRIE_________________________________
Assurez-vous qu’il n’y a pas de signes de dommages évidents ou cachés suite au transport. En cas de dommage,
remplissez immédiatement une réclamation avec la compagnie de transport. Assurez-vous que toutes les pièces
endommagées sont remplacées et les problèmes mécaniques et électriques corrigés avant l’utilisation de l’appareil.
Si vous avez besoin d'assistance, entrez en contact avec votre service clientèle 1-800-553-9053.
Veuillez avoir les informations suivantes disponibles pour toute intervention:
1. Numéro de modèle
2. Numéro de série
3. Date et lieu d'achat

20 Manuel opérateur d'aspirateur eau/poussière
AVERTISSEMENTS DE SÉCURITÉ
AVERTISSEMENT: Lors de l'utilisation de ce produit, des précautions de base doivent toujours être observées, incluant les suivantes:
LIRE TOUTES LES INSTRUCTIONS AVANT UTILISATION DE L'ASPIRATEUR EAU/POUSSIERE
CONSÉQUENCE POTENTIELLE PRÉVENTION
Des risques de mort ou de
blessures graves peuvent survenir
si l'aspirateur eau/poussière n’est
pas reliée à la terre correctement.
Votre aspirateur eau/poussière est
alimenté par électricité et pourrait
provoquer une décharge électrique
ou une électrocution si il n’est pas
utilisé correctement.
Cet appareil doit être relié à la terre. Ne brancher
qu'à une prise correctement mise à la terre. Voir
les "instructions de mise à la terre".
Assurez-vous que l’appareil reçoit toujours le
voltage approprié. Avant de brancher l’appareil
à une source d’énergie compatible, assurez-
vous que l'interrupteur est en position “Arrêt”
(Off). Débrancher entre chaque utilisation.
Ne modier en aucun cas la prise fournie
avec le produit. Si celle-ci n’entre pas dans
la prise femelle, faites-en installer une par un
électricien qualié. Ne pas enlever la prise ou
utiliser aucun type d’adaptateur.
Ne pas exposer l'aspirateur eau/poussière à la
pluie ou immerger dans l'eau. Ne pas utiliser
d'eau sous pression pour nettoyer l'aspirateur
eau/poussière. Entreposer à l'intérieur.
Vérier que le cordon d’alimentation n’a pas
d’écrasement, de coupures ou de dommages
résultant de la chaleur. Si une prise ou un
cordon d’alimentation a besoin d’être changé,
remplacez-le avec un produit identique.
Rapporter l'aspirateur eau/poussière à un centre
de service s'il ne fonctionne pas correctement, si
vous l'avez laissé tombé, si il est abîmé, si il a été
laissé dehors, ou si il est tombé dans l'eau.
Garder tous les branchements au sec et au dessus
du sol. Ne pas permettre aux ls électriques de
tremper dans l'eau ou de se retrouver dans une
position telle que le contact avec l'eau serait
possible. Ne pas toucher la prise ou l'aspirateur
eau/poussière avec les mains mouillées.
Ne pas tirer sur ou porter l'appareil par le l
électrique. Ne pas se servir du l comme d'une
poignée, fermer la porte sur le l, ou tirer le l
sur des coins ou bords aigus. Ne pas passer
l'aspirateur eau/poussière sur le l. Placer le l
loin de toute surface chaude.
Eteindre toutes les commandes avant de
débrancher l'appareil de la prise. Ne pas
débrancher en tirant sur le l. Pour débrancher,
saisir la prise, pas le l.
Utiliser seulement des rallonges ayant une
intensité électrique au moins égale à l’intensité
électrique du produit. N’employer pas de
rallonges électriques abîmées. Examiner la
rallonge avant chaque utilisation et remplacer-
la si elle est endommagée. Tenir le l
électrique à l’écart de la chaleur et des bords
coupants. Brancher et débrancher toujours
la rallonge électrique du réceptacle avant de
brancher ou débrancher celle-ci de l'appareil.
Toute réparation ou câblage électrique effectué
sur l'aspirateur eau/poussière doit être réalisé
par le Personnel de Service Autorisé et selon
les dispositions électriques nationales et
locales en vigueur.
Avant d’ouvrir n’importe quel boîtier électrique,
toujours éteindre l'aspirateur eau/poussière
et débrancher l'aspirateur eau/poussière de
la source d’énergie. Laisser l'aspirateur eau/
poussière refroidir. Entretenir dans un endroit
propre, sec, et plat.
RISQUE DE DÉCHARGE
ÉLECTRIQUE OU
D'ÉLECTROCUTION
Des risques de mort ou de
blessures graves peuvent survenir
si des réparations électriques sont
effectuées par des personnes
incompétentes.
Un choc électrique peut se produire
par le l électrique.
RISQUE