Michele Deco Park MWW06E000142 User manual

1
ENGLISH
Thank you for purchasing this MICHELE watch. The precision and
quality of the quartz movement assures excellent accuracy and
never needs winding.
The following instructions are provided to help you familiarize
yourself with the proper operation and care of your MICHELE
watch. To ensure correct use, please read and follow the
instructions carefully.
All diamonds used on MICHELE watches are genuine diamonds
and sourced from non-conict areas. The total carat weight and
number of stones are marked on the back of the case.

2
2 AND 3 HANDS MODELS
(RONDA 703, 762, 773, 783, 713, 753, 763, 1069)
III
III
III
Time Setting
1. Pull crown out to position II.
2. Turn crown clockwise to rotate hour and minute hands to desired time.
3. Push crown back to position I.
Minute
Minute
Minute
Hour
Hour
Hour
Seconds Seconds

3
DATE MODELS (RONDA 705, 715, 785)
Setting the Time
Setting the Date
Do not change the date between the hours of 10pm and 2am.
This is the time when the movement is in position to carry out the automatic date
change, and any interference may cause damage to the movement.
For rapid correction of date, turn the crown either clockwise or counter-clockwise to set
the date. The direction varies according to the movement.
Rapid correction of date
Display 2
Display 1
Display 3
Closed
II III
Rotate to set
hour & minute
hands. Date
advances with
each 24 hour
rotation of
hour hand.
I
Rapid correction of date
Display 2
Display 1
Display 3
Closed
II III
Rotate to set
hour & minute
hands. Date
advances with
each 24 hour
rotation of
hour hand.
I

4
CHRONOGRAPH MODELS (ETA 251)
Minute Hand
Hour Hand
Second Hand
1/10 Second Timer
Pusher A
Crown
(Position I, II, III)
Pusher B
Date Indicator
III III
60 Seconds Timer
30 Minutes Timer
Display 1
Display 2

5
Zero Reset
Set the hand of the
1/10 second timer to zero
Set the hand of the
30 minutes timer to zero
Set the hand of the
60 seconds timer to zero
Crown
I II III
NOTE: To reset the timer hands (60 seconds hand, 30 minutes hand and 1/10
seconds hand) press Pusher A or B. Each time you press the pusher, it will advance
the hands by a single unit. If you hold the pusher pressed in for more than 2
seconds, it advances rapidly.
WARNING: Before adjusting the Zero Reset, put back the chronograph hands to their
original position to ensure that the chronograph timer is not running.

6
Correction Mode
Setting the Time
Setting the Date
Time Zone Correction
NOTE: While crown is in position
III, the second hand stops rotating.
Timing Mode
Simple Timing Function
WARNING: Before starting the
timer, put back the chronograph
hands to their original positions.
If necessary, see diagram titled
“Zero Reset.”
I II III
A
B
Time zone correction
Rotate to set
hour & minute
hands. Date
advances with
each 24 hour
rotation of
hour hand.
Reset to zero
START
Setting crown
in position l
STOP
Read time - example:
- 5 minutes
- 57 seconds
- 7/10 second
1
2
3
I
A
B

7
Timing Mode
Split-time or Intermediate Time Function
Crown
in position l
START 1
I
A
B
SPLIT 1
Read time 1
- 5 minutes
- 4 seconds
- 6/10 sec.
2
RESTART 3
I
A
B
SPLIT 2
Read time 2
- 15 minutes
- 36 seconds
- 8/10 sec.
4
RESTART 5
I
A
B
STOP
Read
Last time
- 25 minutes
- 18 seconds
- 4/10 sec.
6
Reset
to zero 7
I
A
B

8
CHRONOGRAPH MODELS (ETA G10, G15)
Setting the Time
1. Pull crown out to position III (the watch stops).
2. Turn crown until you reach correct time.
3. Push crown back into position I.
Setting the Date
1. Pull crown out to position II (the watch continues to run).
2. Turn crown until yesterday’s date appears.
3. Pull crown out to position III (the watch stops).
4. Turn crown until correct date appears.
5. Continue to turn crown until correct time appears.
6. Push crown back into position I.
Minute Hand
Hour Hand
Second Hand
Pusher A
Crown
(Position I, II, III)
Pusher B
Date Indicator
III III

9
Chronograph
• The minute counter measures 30 minutes per rotation.
• The center stop-second measures 60 seconds per rotation.
PLEASE NOTE:
Before using the chronograph functions, please ensure that:
- the crown is in position I (= normal position).
- the three chronograph hands are precisely at zero position following activation of
pusher B. Should this not be the case, the positions of the hands must be adjusted
(see chapter entitled “Adjusting the chronograph hands to zero”).
Chronograph: Basic Function
(Start / Stop / Reset)
1. Press pusher A to start the center stop-second hand.
2. To stop the timing, press pusher A again.
3. To reset the three chronograph hands to zero positioning, press pusher B.
1/10 Second Counter
Pusher A
Crown
(Position I, II, III)
Pusher B
III III
Minutes Counter
Center Stop-second

10
Chronograph: Intermediate or Interval Timing
1. Press pusher A to start the center stop-second hand.
2. Press pusher B to stop the chronograph.
*NOTE: Although the chronograph hands have stopped, the movement continues
to record the current timing.
3. Make up the measured time:
Press pusher B again and the 3 chronograph hands are quickly advanced to the
ongoing measured time. To continue to record intervals, continue to push pusher B.
4. Press pusher A to stop and the final time is displayed.
5. To reset the three chronograph hands to zero positioning, press pusher B.
Adjusting the Chronograph Hand to Zero
1. Pull crown out to position II (all 3 hands are in their correct or incorrect position).
2. Press pusher B to single step the minute counter hand. Press and hold pusher B to
advance the minute counter hand quickly.
3. Pull crown out to position III.
4. Press pusher A to single step the center stop-second hand. Press and hold pusher
A to advance the center stop-second hand quickly.
5. Press pusher B to single step the 1/10 second hand. Press and hold pusher B to
advance the 1/10 second hand quickly.
6. Return the crown to position I.

11
CHRONOGRAPH MODELS (ISA 8171/204)
Time Setting
1. Pull crown out to position 3.
2. Rotate crown to set correct am/pm time.
3. Return crown to position 1.
Date and Moonphase Setting
1. Pull crown out to position 2.
2. Rotate crown clockwise and the set date according to the last full moon.
3. Continue to rotate crown clockwise to set the date.
4. Return crown to position 1.
NOTE: Do not set the date between 9:00 p.m. and 12:30 a.m. to ensure accuracy.
Chronograph Operation
1. Press A to start/stop the chronograph.
2. Press B to reset.
NOTE: After 2 hours of continuous running, the chronograph will automatically stop
and reset to save the battery.
I II III
Chronograph Minute Hand
Date Indicator
Crown
(Position I, II, III)
Pusher A
Pusher B
Second Hand
Moonphase
Chronograph 1/5 Second Hand

12
Split Time
1. Press B while the chronograph is running.
2. Press B again to return to the chronograph.
3. Press A to finalize timing.
4. Press B to reset.
Chronograph Zero Reset
1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out
to position 2.
2. Press B to reset chronograph minute hand. Each press of B will advance the
chronograph minute hand by one increment, or press and hold B for fast advance.
3. Press A to reset chronograph 1/5 second hand. Each press of A will advance
the chronograph 1/5 second hand by one increment, or press and hold A for
fast advance.
4. Return crown to position 1.

13
CHRONOGRAPH MODELS (ISA 8172/220)
Setting the Time
1. Pull crown out to position III (the watch stops).
2. Turn crown until you reach correct time.
3. Push crown back into position I.
PLEASE NOTE: The day of the week changes with each 24 hour rotation.
Setting the Date
1. Pull crown out to position II (the watch continues to run).
2. Turn crown until correct date appears.
3. Push crown back into position I.
PLEASE NOTE: Do not set the date between 9:00 p.m. and 12:30 a.m.
S
U
N
M
O
N
T
U
E
W
E
D
T
H
U
F
R
I
S
A
T
III III
S
U
N
M
O
N
T
U
E
W
E
D
T
H
U
F
R
I
S
A
T
Minute Hand
Date Indicator
Crown
(Position I, II, III)
Pusher A
Pusher B
Hour Hand
Second Hand
Display 1
Display 2

14
Chronograph
• The minute counter measures 30 minutes per rotation.
• The center stop-second measures 60 seconds per rotation.
PLEASE NOTE:
Before using the chronograph functions, please ensure that:
- The crown is in position I (= normal position)
- The two chronograph hands are precisely at zero position following activation of
pusher B. Should this not be the case, the positions of the hands must be adjusted.
(see chapter entitled “Adjusting the chronograph hands to zero”).
Chronograph: Basic Function
(Start / Stop / Reset)
1. Press pusher A to start the center stop-second hand.
2. To stop the timing, press pusher A again.
3. To reset the 2 chronograph hands to zero positioning, press pusher B.
III III
S
U
N
M
O
N
T
U
E
W
E
D
T
H
U
F
R
I
S
A
T
Crown
(Position I, II, III)
Pusher A
Pusher B
Center Stop-second
Minutes Counter
Seconds Counter
Weekday

15
Chronograph: Intermediate or interval timing
1. Press pusher A to start the center stop-second hand.
2. Press pusher B to stop the chronograph.
*NOTE: Although the chronograph hands have stopped, the movement continues
to record the current timing.
3. Make up the measured time:
Press pusher B again and the 2 chronograph hands are quickly advanced to the
ongoing measured time. To continue to record intervals, continue to push pusher B.
4. Press pusher A to stop and the final time is displayed.
5. To reset the 2 chronograph hands to zero positioning, press pusher B.
Adjusting the chronograph hand to zero
1. Pull crown out to position II (Chronograph hands are in their correct or incorrect
position).
2. Press pusher B to single step the minute counter hand. Press and hold pusher B to
advance the minute counter hand quickly.
3. Press pusher A to single step the center stop-second hand. Press and hold pusher
A to advance the center stop-second hand quickly.
4. Return the crown to position I.

16
CHRONOGRAPH MODELS
(RONDA 5030.D, 5040.D, 5050.B)
Setting the Time
1. Pull crown out to position III (the watch stops).
2. Turn crown until you reach correct time.
3. Push crown back into position I.
Setting the Date
1. Pull crown out to position II (the watch continues to run).
2. Turn crown until yesterday’s date appears.
3. Pull crown out to position III (the watch stops).
4. Turn crown until the correct date appears.
*NOTE: When the correct date first appears, your watch is set at midnight.
5. Continue to turn crown until the correct time appears.
6. Push crown back into position I.
III III III III
Minute Hand
Crown
(Position I, II, III)
Pusher A
Pusher B
Hour Hand
Second Hand
Date Indicator Date Indicator
5040.D 5050.B

17
Chronograph
• The minute counter measures 30 minutes per rotation.
• The center stop-second measures 60 seconds per rotation.
PLEASE NOTE:
Before using the chronograph functions, please ensure that:
- The crown is in position I (= normal position)
- The two chronograph hands are precisely at zero position following activation of
pusher B. Should this not be the case, the positions of the hands must be adjusted.
(See chapter entitled “Adjusting the chronograph hands to zero”).
Chronograph: Basic Function
(Start/ Stop/ Reset)
1. Press pusher A to start the center stop-second hand.
2. To stop the timing, press pusher A again.
3. To reset the 3 chronograph hands to zero positioning, press pusher B.
III III
Crown
(Position I, II, III)
Pusher A
Pusher B
Center Stop-second
5040.D: 30 Minute Counter
5050.B: 30 Minute Counter
and Hour Counter
Seconds Counter
1/10 Seconds Counter

18
Chronograph: Intermediate or interval timing
1. Press pusher A to start the center stop-second hand.
2. Press pusher B to stop the chronograph.
*NOTE: Although the chronograph hands have stopped, the movement continues
to record the current timing.
3. Make up the measured time:
Press pusher B again and the 3 chronograph hands are quickly advanced to the
ongoing measured time. To continue to record intervals, continue to push pusher B.
4. Press pusher A to stop and the final time is displayed.
5. To reset the 3 chronograph hands to zero positioning, press pusher B.
Adjusting the Chronograph Hand to Zero
1. Pull crown out to position III (all 3 hands are in their correct or incorrect position.)
2. Press pushers A and B simultaneously for at least 2 seconds. Center stop hand will
rotate 360 degrees. Corrective mode is activated.
3. To adjust the center stop-second hand, press pusher A one time. Press and hold
pusher A until the second hand lines up with the 12 o’clock position.
4. To adjust the 1/10 second hand, press pusher B one time. Press and hold pusher A
until the 1/10 second hand lines up with the 10.
5. To adjust the minute counter hand, press pusher B one time. Press and hold pusher
A until the minute counter hand lines up with the 30 (5040.D) or the 12 (5050.B)
6. Return crown to position I.

19
BATTERY LIFE
If your MICHELE timepiece has a chronograph function, you can extend its battery life
by ensuring the chronograph function does not run continuously.
*NOTE: The chronograph function is in use when the large second hand is in motion.
1. To stop the chronograph, press pusher A one time.
2. To reset the large second hand to the 12 position, press pusher B one time.
The average battery life when the chronograph is not in use is 2 years. Continuous use
of the chronograph will reduce the average life to approximately 1 year.
I
A
B
Crown in position I
RESET
STOP
Second Hand

20
WATER RESISTANCE
All MICHELE timepieces are designed with a minimum water-resistance rating of
5ATM (165ft/50m).
See caseback for water resistance rating for traditional watches and Hybrid Smartwatches.
The water resistance rating provides guidelines for appropriate water-related exposure to
avoid damage to internal watch components. Please see chart for recommended usage
guidelines.
In order to ensure water does not enter the watch and cause damage to it, please follow the
instructions listed below:
• Do not adjust the crown while the timepiece is in contact with water.
• Ensure the crown is in the closed position before contact with water. For timepieces with
screw-down crowns, ensure the crown is completely tightened before contact with water.
• For timepieces with pusher-enabled functionality, do not engage the function underwater.
• Exposure to extreme atmopheres is not recommended (i.e. hot water, saunas or steam
rooms).
• Avoid exposure to water moving with force (i.e. water running from a faucet, ocean waves
or waterfalls).
• Avoid long exposure to salt water. After contact with salt water, rinse watch under tap water
if rated 5ATM or higher and wipe dry with a soft cloth.
RECOMMENDATIONS FOR WATER-RELATED USE
INDICATION
SPLASH RESISTANT SUBMERSIBLE SHALLOW DIVING SCUBA DIVING
(Hand Washing) (Swimming) (Snorkeling) (Not Deep Sea)
(NONE)
3 ATM • 3 BAR • 30 Meters
5 ATM • 5 BAR • 50 Meters
10 ATM • 10 BAR • 100 Meters
20 ATM • 20 BAR • 200 Meters