MicroNet T262-T21D User manual

User Guide
AX1500 Wi-Fi 6 Router
T262-T21D

•Specifications:
WiFi Standard: IEEE802.11b/g/n IEEE802.11a/n/ac/ax
Interface: 1 WAN 3 LAN
•Environment:
Rated Power Input: 12VDC, 1A
Operating Temperature: 0-40℃
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

Safety Instruction
1.WARNING: To reduce the risk of fire or electric shock, do not expose this device to rain or moisture. The device shall not
be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus.
2.WARNING: the power plug/direct plug-in adpater is used as disconnect device, the disconnect device shall remain readily
operable.
3. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer or service operator where the product was purchased. They can take
this product for environmental safe recycling.
4.Warning: to reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside.
Refer servicing to qualified personnel.
5.The power adapter is used as the power interrupting d evice. Please pay attention to safety plug and pull and convenient
operation.
6.Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside.
Refer servicing to qualified personnel.
7.Use only the AC adapter which is included in the product package. Any other adapter may cause damage to the device.
Such damage is not covered under warranty.
8.Please use and store the router and its accessories within the temperature range of 0℃~40℃. When the temperature is
too high or too low, it may cause equipment failure.
9.WARNING: The direct plug-in adapter is used as disconnect device, the disconnect device shall remain readily operable.

FCC Warning Statement
FCC Radiation Exposure Statement:
The antennas used for this transmitter must be installed to provide aseparation distance of at least 20cm from all persons and must not be
co-located for operating in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1.Reorient or relocate the receiving antenna.
2.Increase the separation between the equipment and receiver.
3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4.Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause
harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation

1.1 The first step to start configuring your router is
to plug it in and then connect a network cable
（RJ45）to your WAN port, the other side of
network cable (RJ45) must also be connected to
your home Modem (xDSL/PON).
1.2 After plugging in the router and connecting it
to the Modem, proceed to the next topic, which is
the configuration step by step.
1.3 If your internet connection is through an
Ethernet cable from the wall instead of through a
home Modem (xDSL/PON) , connect the Ethernet
cable directly to the router’s Internet port.
1. Connect the Router
6
Switch on the
router.And waiting
for the LED turns
into green.
4 Connect the
power adapter
cable to the
router’s DC-IN
and turn it on.
5
Plug the router
and modem’s
power adapter.
3
Connect the
router's WAN
port with the
Ethernet
cable
2
Connect the
modem’s
LAN port with
the Ethernet
cable 1
Power off or
unplug your
modem

2. Indicator
LED Status Description
Off The router is power off
Red On The router is power on but Internet is not working
Green On The router is already connected to the internet
Green Flashing WPS or Mesh pairing

3. Connect Device to the Router
3.1 Wireless
Activate the Wi-Fi on your smartphone or notebook, connect to the router's 2.4GHz or 5GHz network with the SSID provided at the bottom
of the router and enter the IP address 192.168.10.1 in any browser;
•Find the SSID and SSID password printed on the label at the bottom of the router.
•Click the network icon of your computer or go to WiFi settings of your smart device, and then select the SSID and input password to join
the network.
3.2 Wired
Connect a network cable(RJ45) to the LAN port of the router and the other side of network cable(RJ45) connect to a notebook or desktop
and enter the IP address 192.168.10.1 in the browser. Remember to turn off the device's Wi-Fi before performing this step.

4. Configure your router via Web
Open the mobile phone or computer browser, visit the
192.168.10.1 website, enter the default Username and
Password on the label at the bottom of the router, then you
can enter the router management page.
When the router is configured for the first time, it will
automatically enter the Install page (setup wizard).
Select WAN Access Type , normally “DHCP”
Create a password for each Wi-Fi band (2.4GHz and 5GHz)
and if you want, change the SSID (2.4GHz and 5GHz) to
your preference name .
Save the configuration , enjoy the Internet.
Notice : For the WANAccess Type depend on ISP , you
can consult the ISP for confirmation.

5. WAN Access Type
5.1 DHCP: For Cable/DSL/Broadband connection which makes your computer immediately online without any setting or signing-in.
5.2 Static IP: You are provided with specified IP parameters by your ISP.
5.3 PPPOE: Usually for ADSL Modem and you are provided with a PPPoE username and password by your ISP.