MicroNet SP3366 User manual

User’s Manual
ADSL2+ VPN Modem Router
Model No.: SP3366
World Wide Web: www.micronet.com.tw ; www.micronet.info

Table of Contents
Chapter 1 Introduction................................................................................. 2
1.1 Package Contents..........................................................................................2
1.2 Key Features .................................................................................................2
1.3 Specifications................................................................................................3
Chapter 2 Tour of Product........................................................................... 5
2.1 Front Panel....................................................................................................5
2.2 Back Panel.....................................................................................................5
Chapter 3 Hardware and Network Setup.................................................... 7
3.1 Build Network Connection...........................................................................7
3.2 Connecting to Web-Based Management ......................................................8
3.2.1 IP Address Configuration.....................................................................................8
3.2.2 Starting Web-Based Management UI................................................................11
Chapter 4 Web-Based Management UI .................................................... 14
4.1 Quick Start ..................................................................................................14
4.2 Status...........................................................................................................16
4.2.1 ADSL Status ......................................................................................................16
4.2.2 ARP Table..........................................................................................................17
4.2.3 DHCP Table.......................................................................................................18
4.2.4 Routing Table.....................................................................................................18
4.2.5 NAT Session......................................................................................................19
4.2.6 UPnP Portmap....................................................................................................19
4.2.7 Email Status .......................................................................................................20
4.2.8 Event Log...........................................................................................................20
4.2.9 Error Log............................................................................................................21
4.2.10 Diagnostic ..........................................................................................................21
4.3 Configuration..............................................................................................21
4.3.1 LAN ...................................................................................................................21
4.3.2 WAN..................................................................................................................27
4.3.3 System................................................................................................................34

4.3.4 Firewall & Access Control.................................................................................38
4.3.5 QOS – Quality of Service ..................................................................................45
4.3.6 VPN....................................................................................................................49
4.3.7 Virtual Server/ Port Forwarding ........................................................................60
4.3.8 DMZ Host..........................................................................................................61
4.3.9 One-to-One NAT ...............................................................................................62
4.3.10 Time Schedule....................................................................................................64
4.3.11 Advanced ...........................................................................................................65
4.4 Logout.........................................................................................................72

Certifications
FCC
This equipment has been tested and found to comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference
(2)This device must accept any interference received. Include interference that may
cause undesired operation.
CE
This equipment is in compliance with the requirements of the following regulations:
EN 55 022: CLASS B.
RoHS
All contents of this package, including products, packing materials and
documentation comply with RoHS.
1

Chapter 1 Introduction
Micronet SP3366, ADSL2+ VPN Modem Router, delivers highly reliable and scalable
network environment. The model has incorporated both modem and router functions into
a single unit with VPN support. The modem router allows multiple network devices to
share the single Internet connection via ADSL. Sustain network security via router’s in-
built firewall and DMZ functions. In addition, the scope of the network can be easily
expanded by connecting the router to a hub or switch.
1.1 Package Contents
Prior to the installation of the device, please verify the following items are in the
package:
ySP3366 ADSL2+ Modem Router
yQuick Installation Guide
yProduct CD
yRJ-45/RJ-11 Cables
yRJ-45-RS232 Console Kit
yPower Adapter
Note: Contact your dealer immediately if any of the above items are missing,
damaged, or if the unit does not work.
1.2 Key Features
yCompliant with ADSL/ADSL2/2+ standards.
yProvide 16 IPSec Virtual Private Network (VPN) connections with powerful
3DES accelerator.
yQuality of Service (QoS) via Traffic Prioritization and Bandwidth Management.
ySupport CPE WAN Management Protocol (TR-069) for remote configuration of
client side devices.
2

ySupport IGMP Snooping for reducing Multicast traffic to enhance video service.
yIn-built Firewall Security with DoS Prevention and SPI for secure networks.
ySupport advanced router functions: Static Route, Virtual Sever, DDNS and
UPnP.
yMonitoring network traffics through Event, Error and Firewall logs.
1.3 Specifications
Standards zANSI T1.413 ,Issue 2
zG.dmt (ITU G.992.1)
zG.lite (ITU G.992.2)
zG.hs (ITU G994.1)
zG.dmt.bis (ITU G.992.3)
zG.dmt.bis.plus (ITU G.992.5)
Interface zWAN Port: 1 x Port 10/100Mbps RJ-11
zLAN Ports: 4 x Port 10/100Mbps RJ-45
WAN Connection zPPPoA
zPPPoE
zIPoA
zATM (Bridge & Routed)
DHCP DHCP Server & Client
Routing zNAT/NAPT (Network Address Translation)
zStatic and RIP1/2 Routing
Advance Features zSupport NAT
zDNS Relay
zDDNS
zQoS
zVirtual Server
zVLAN Bridge
3

zIGMP
zUPnP
zALG
Security Features zFirewall (DoS & SPI)
zIP Filtering
zPacket Filter
zURL Filter
zIM/ P2P Blocking
Status Log zEvent Log
zError Log
zPacket Filter
zFirewall Log
Management zWeb-based Interface
zSNMP
zTelnet
Power 12V DC, 1A
Humidity 20 ~ 95% (Non-Condensing)
Temperature zOperating: 0 ~ 40°C
zStorage: -20 ~ 70°C
Certification FCC, CE
4

Chapter 2 Tour of Product
2.1 Front Panel
LED Status Description
Green Device is switched on.
Red System failure. Restart device.
Power
Off No power.
Green LAN port is connected and
operating at 100Mbps.
Amber LAN port is connected and
operating at 10Mbps.
LAN
(1-4)
Flashing Data is being sent or received.
Mail Flashing Received emails in the inbox.
Line Green Device successfully connected to
DSLAM (line sync).
Green WAN IP successfully assigned.
ADSL
Red Unable to obtain WAN IP from
ISP.
2.2 Back Panel
5

Parameter Description
Power Power connector for connecting to power source.
On/Off For powering device on and off.
Reset Press and hold this button for more than 6 seconds
to reset settings back to factory default.
LAN 1~4 Local Area Network (LAN) ports for 1 to 4.
ADSL Connection to RJ-11 telephone line for Internet.
6

Chapter 3 Hardware and Network Setup
3.1 Build Network Connection
To install the SP3366 Modem Router, please perform the following steps:
Step 1. Connect the ADSL port of modem router by telephone cable (RJ-11) to an
outlet or splitter.
Step 2. Connect the LAN port to an active PC, switch, or hub using an Ethernet cable
(RJ-45).
Step 3. Connect the 12V DC power adapter to a power outlet.
Step 4. Connect the adaptor to the power port on the back of the router. Switch
device on using On/Off button.
Step 5. Check the LED indicators to verify that the device is detecting connection on
Line and LAN.
7

Warning: Using an alternate power supply, other than the one supplied, may cause
the router to malfunction.
3.2 Connecting to Web-Based Management
After the network connection is established, the next step is to setup the modem
router with proper network parameters for the user’s network environment.
Before connecting to the modem router and start configuration procedures, user’s
computer must be able to get an IP address automatically (use dynamic IP address).
If the PC is set to ‘static IP address’, then follow instructions below to reconfigure it to
‘dynamic IP address’.
3.2.1 IP Address Configuration
a) Windows 95/98/Me
1. Click the Start button and select <Settings>, then click <Control Panel>. The
Control Panel window will appear.
2. Double-click on <Network> icon. The Network window will appear.
3. Check the list of Network Components. If TCP/IP is not installed, click the
<Add> button to install it. If TCP/IP is installed, go to step 6.
4. In the Network Component Type dialog box, select <Protocol> and click
<Add> button.
5. In the Select Network Protocol dialog box, select <Microsoft> and <TCP/IP>
then click the <OK> button to start installing the TCP/IP protocol. Windows CD
may be needed to complete the installation.
6. After installing TCP/IP, go back to the Network dialog box. Select <TCP/IP>
from the list of Network Components and then click the <Properties> button.
7. Check each of the tabs and verify the following settings:
yBindings: Check Client for Microsoft Networks and File and printer sharing
for Microsoft Networks.
yGateway: All fields are blank.
yDNS Configuration: Select Disable DNS.
8

yWINS Configuration: Select Disable WINS Resolution.
yIP Address: Select Obtain IP address automatically.
8. Reboot the PC. PC will now obtain an IP address automatically from the
Broadband Router’s DHCP server.
9. Please make sure that the Broadband router’s DHCP server is the only DHCP
server available on the LAN network.
10.Proceed to Web-based User Interface once IP address is correctly configured.
b) Windows 2000
1. Click the <Start> button and select <Settings>, then click <Control Panel>.
The Control Panel window will appear.
2. Double-click <Network and Dial-up Connections> icon. In the Network and
Dial-up Connection window, double-click on <Local Area Connection> icon.
The Local Area Connection window will appear.
3. In the Local Area Connection window, click the <Properties> button.
4. Check the list of Network Components. Users should see Internet Protocol
[TCP/IP] on the list. Select it and click the <Properties> button.
5. In the Internet Protocol (TCP/IP) Properties window, select <Obtain an IP
address automatically> and <Obtain DNS server address automatically>
as shown on the following screen.
9

6. Click <OK> to confirm the setting. The PC will now obtain an IP address
automatically from the Broadband Router’s DHCP server.
7. Please make sure that the Broadband router’s DHCP server is the only DHCP
server available on the LAN network.
8. Proceed to Web-based User Interface once IP address is correctly configured.
c) Windows XP
1. Click the <Start> button and select <Settings>, then click <Network
Connections>. The Network connections window will appear.
2. Double-click <Local Area Connection> icon. The Local Area Connection
window will appear.
3. Check the list of Network Components. Users should see Internet Protocol
[TCP/IP] on the list. Select it and click the <Properties> button.
4. In the Internet Protocol (TCP/IP) Properties window, select <Obtain an IP
address automatically> and <Obtain DNS server address automatically>
as shown on the following screen.
10

5. Click <OK> to confirm the setting. PC will now obtain an IP address
automatically from the Broadband Router’s DHCP server.
6. Please make sure that the Broadband router’s DHCP server is the only DHCP
server available on the LAN network.
IP Address 192.168.1.254
Subnet Mask 255.255.255.0
Username ‘admin’
Password ‘admin’
3.2.2 Starting Web-Based Management UI
1. After the computer has obtained an IP address from modem router, please start the
web browser. Input the IP address of router (Default: 192.168.1.254) in the address
bar and the following message should appear:
11

2. Please input username and password in the field respectively. Default username is
‘admin’ and default password is ‘admin’, then press <OK> button. Once the login
details are entered correctly, users can see the web management interface of this
modem router.
3. For all changes to the setting on the Web UI, please click on ‘Save Config’ to
permanetly save configuation to FLASH. Otherwise, rebooting device will cause the
current changes to the setting to be ignored.
12

13

Chapter 4 Web-Based Management UI
4.1 Quick Start
The ‘Quick Start’ section is designed to get the modem router running as quickly as
possible. In the ‘Quick Start’, users are required to fill in only the information
necessary to access the Internet. Once user clicks on the <Quick Start> on the
menu to the left, the following screen will appear.
Step 1: ADSL Status
If below message are shown, the ADSL line is not ready. Please wait for few minutes
to allow the line to synchronize.
Step 2: ADSL Status
If ADSL line is ready, the screen will appear ‘ADSL Line is Ready’. Choose ‘Auto’ and
click <Apply>. It will automatically scan the recommended mode for the connection.
‘Manually’ mode requires user to set the ADSL line (Proceed to step 5 if ‘Manually is
selected).
14

Step 4: Auto Scan
The list below has different mode suitable for the connection.
Step 5: Internet Account
Please enter “Username” and “Password” supplied by ISP (Internet Service Provider)
and click <Apply> to continue.
Parameter Description
Profile Port Select the connection mode.
Encapsulation Select the encapsulation mode.
Default: ‘PPPoE’.
VPI/VCI Enter the VPI and VCI information provided by ISP.
Username Enter the username provided by ISP.
Password Enter the password provided by ISP.
Service Name This item is for identification purposes. It is optional
depending on ISP.
15

Authentication
Protocol
Chose the protocol used by ISP (CHAP or PAP)
Default: ‘Auto’.
IP Address WAN IP address supplied by ISP. Leave this at 0.0.0.0 to
automatically obtain an IP address from ISP.
Step 6: Auto Scan
The device will save configuration to Flash and initiate Internet access.
4.2 Status
4.2.1 ADSL Status
This section displays the ADSL overall status, which shows a number of helpful
information such as DSP firmware version.
16

4.2.2 ARP Table
This section displays the router’s ARP (Address Resolution Protocol) Table, which
shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is
useful as a quick way of determining the MAC address of the network interface of
PCs for router’s Firewall – MAC Address Filter function. See the Firewall section of
this manual for more information on this feature.
Parameter Description
IP Address A list of IP addresses of devices on the LAN (Local Area
Network).
MAC Address The MAC (Media Access Control) addresses for each device
on the LAN.
Interface The interface name (on the router) that this IP Address
connects to.
17