MICROWELL HP 1100 GREEN INVERTER PRO User manual

Version: 05/2020
Installation and user manual
for swimming pool water
HP 1100
GREEN
&
HP 1500
GREEN
Installation and user manual
HEAT
PUMP
for swimming pool water
heating & cooling
GREEN
INVERTER PRO
&
GREEN
INVERTER PRO
Installation and user manual

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
Thank you
use this device, it is necessary to carefully read the entire Installation and
user
manual. It is not allowed to commence the heat pump installation or
operation unless full content of this Installation and user manual is
understood and acknowledged. Please keep the Installation and user
manual available in the case of any future referenc
provide this information also to each user of the device. Please mind local
regulations in your country regarding installation and usage of this heat
pump which are valid in addition to this User manual.
Contents
1. INTRODUCTION
................................
1.1 Product description
................................
1.2 Package checking
................................
1.3
Waste disposal information
2. SAFETY MEASURES
................................
2.1 Electrical safety
................................
2.2 Usage precautions
................................
Warning ................................
................................
2.3 Handling precautions
................................
2.4 Transportation
................................
3. TECHNICAL SPECIFICATION
3.1 Technical data
................................
Operating condition and range:
Introduction of different modes:
3.2 Swimming pool water
parameters
3.3
Heat pump dimensions
3.4
Description of the basic parts
3.5 Installation reminder
................................
3.6 Accessories
................................
3.7 Electric wiring Di
agram
4. REGULATION
................................
4.1
Description of the LCD panel
4.2 Operation Instruction
................................
4.3 Testing
................................
................................
................................
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
Thank you
for purchasing Microwell swimming pool heat pump. Before you
use this device, it is necessary to carefully read the entire Installation and
manual. It is not allowed to commence the heat pump installation or
operation unless full content of this Installation and user manual is
understood and acknowledged. Please keep the Installation and user
manual available in the case of any future referenc
e is required. Please
provide this information also to each user of the device. Please mind local
regulations in your country regarding installation and usage of this heat
pump which are valid in addition to this User manual.
................................
................................
................................
................................
................................
................................
................................
................................
................................
Waste disposal information
................................................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................................................
................................
................................
................................
................................
Operating condition and range:
................................................................
................................
Introduction of different modes:
................................................................
................................
parameters
................................
................................
Heat pump dimensions
................................................................
................................
Description of the basic parts
................................................................
................................
................................
................................
................................
................................
................................
................................
agram
................................................................
................................
................................
................................................................
................................
Description of the LCD panel
................................................................
................................
................................
................................
................................
................................
................................................................
................................
................................
................................
................................
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 2/ 3 6
for purchasing Microwell swimming pool heat pump. Before you
use this device, it is necessary to carefully read the entire Installation and
manual. It is not allowed to commence the heat pump installation or
operation unless full content of this Installation and user manual is
understood and acknowledged. Please keep the Installation and user
e is required. Please
provide this information also to each user of the device. Please mind local
regulations in your country regarding installation and usage of this heat
................................
............................... 4
................................
................. 4
................................
..................... 5
................................
.... 5
................................
.......................... 6
................................
........................ 6
................................
................... 6
................................
............... 7
................................
.............. 9
................................
......................... 9
................................
........... 10
................................
........................ 10
................................
........ 11
................................
...... 11
................................
........................ 11
................................
......... 12
................................
12
................................
............. 13
................................
............................ 14
................................
.......... 14
................................
.. 20
................................
. 20
................................
............ 21
................................
... 24
................................
........................... 24

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 3/ 3 6
5. WIFI OPERATION
................................
6. TROUBLE SHOOTING
FOR COMMON FAULTS
6.1 Repairing Guidance
................................
6.2
Failure solution and code
7.
MAINTANANCE & WARRANTY
7.1 Maintanance
................................
7.2 Warranty
................................
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
................................
................................
................................
FOR COMMON FAULTS
................................
................................
................................
................................
................................
Failure solution and code
................................................................
................................
MAINTANANCE & WARRANTY
................................................................
................................
................................
................................
................................
................................
................................................................
................................
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
................................
........................... 26
................................
............... 30
................................
............... 30
................................
...... 30
................................
...... 32
................................
.......................... 32
................................
33

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
1. INTRODUCTION
In your hands you hold probably the most advanced and the most efficient heat pump currently available on
the market. This heat pump provides warm water in your pool at lowest possible cost. The heat pump is
manufactured in tightest accordance with related
operation and long-
term reliability.
This Installation and user manual contains all the necessary information about the installation, operation and
maintenance of the heat pump. Please read
this product. The manufacturer is not responsible for any personal or property damage due to the improper
installation, use or maintenance that is not in accordance with this User Manual.
This Installation and user manual is an inseparable part of this product; therefore it must be kept in good
condition and must accompany the heat pump.
1.1
Product description
The heat pump is designed exclusively for swimming pool water heating or cooling and
temperature on the requested level. Other appropriate application is water temperature conditioning for fish
tanks, wine ciders or horse cooling facilities. These applications should be discussed with local installer or
distributor. Any ot
her form of application is considered inappropriate.
The heat pump achieves the highest efficiency at 15÷35°C air temperature. At ambient air temperatures lower
than -
15°C the efficiency of the device decreases and at the temperatures higher than +40°C the
can get overheated which may result in its malfunction, damage or failure. Do not use the product out of the
designated operational air temperature range which is stated in section
This heat pump is designed for swimming pools with up to 40 m
water volume. For proper operations there must be water flow through the exchanger of the heat pump
(within water filtration circuit) in the range of 4
The heat pump enables heat gain from the external
compression –
expansion cycles of the heat
where it will deliver its heat to the heat
carrying liquid is then delivered to the spirals of the exchanger by the compressor which pressurises it and thus
heats it up. In these spirals, the heat
exchanger there is a
cooled liquid flowing to the expansion valve or capillary where its pressure decreases and
it gets cooled down rapidly at the same time. This cooled liquid flows to the evaporator again where it gets
heated by the
flowing air. The whole process runs f
temperature sensors. The same principle is applied when heat pump operates in cooling mode.
Using simple language, a heat pump is able to extract the heat/cold that is present in ambient environment
leveraged pass it into the pool water. When heating, higher the ambient air temperature is, more free energy
can the heat pump extract and thus reach higher efficiency. At favourable conditions you pay around 15% of
heat, i.e. 85% of heat is free. Plea
se review below drawing of different ambient air conditions with subsequent
efficiencies.
The heat pump efficiency grows by the increasing surrounding air temperature.
It takes some days to achieve the requested swimming pool water temperature. This time
heat loss and heat gain balance of your pool.
Example factors of heat losses
: poor pool construction, used materials, usage of cover, air
temperature relationship, fresh water refilling, filtration, etc.
Example factors of heat gains
: intensity of sun, winds, orientation of pool, air
relationship, etc.
In order to avoid heat loss when the swimming pool is not being used, it is highly advised to use pool’s cover.
Ideal water temperature for external pools is con
particular demands of the user. When setting the desired air temperature higher than 32°C please review the
material characteristics of your pool parts. High water temperature can damage these ma
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
In your hands you hold probably the most advanced and the most efficient heat pump currently available on
the market. This heat pump provides warm water in your pool at lowest possible cost. The heat pump is
manufactured in tightest accordance with related
strict standards and norms, in order to provide high quality
term reliability.
This Installation and user manual contains all the necessary information about the installation, operation and
maintenance of the heat pump. Please read
this Installation and user manual carefully before you start to use
this product. The manufacturer is not responsible for any personal or property damage due to the improper
installation, use or maintenance that is not in accordance with this User Manual.
This Installation and user manual is an inseparable part of this product; therefore it must be kept in good
condition and must accompany the heat pump.
Product description
The heat pump is designed exclusively for swimming pool water heating or cooling and
temperature on the requested level. Other appropriate application is water temperature conditioning for fish
tanks, wine ciders or horse cooling facilities. These applications should be discussed with local installer or
her form of application is considered inappropriate.
The heat pump achieves the highest efficiency at 15÷35°C air temperature. At ambient air temperatures lower
15°C the efficiency of the device decreases and at the temperatures higher than +40°C the
can get overheated which may result in its malfunction, damage or failure. Do not use the product out of the
designated operational air temperature range which is stated in section
3.1
Technical data
This heat pump is designed for swimming pools with up to 40 m
3 - HP 1000 and up to
60 m
water volume. For proper operations there must be water flow through the exchanger of the heat pump
(within water filtration circuit) in the range of 4
-6 m3/h.
The heat pump enables heat gain from the external
air surrounding the swimming pool through the
expansion cycles of the heat
-
carrying liquid. The air is driven by a fan through the evaporator
where it will deliver its heat to the heat
-
carrying liquid (the air is being cooled at the same tim
carrying liquid is then delivered to the spirals of the exchanger by the compressor which pressurises it and thus
heats it up. In these spirals, the heat
-
carrying liquid delivers its heat to the swimming pool water. From the
cooled liquid flowing to the expansion valve or capillary where its pressure decreases and
it gets cooled down rapidly at the same time. This cooled liquid flows to the evaporator again where it gets
flowing air. The whole process runs f
ully automatically and is monitored by the pressure and
temperature sensors. The same principle is applied when heat pump operates in cooling mode.
Using simple language, a heat pump is able to extract the heat/cold that is present in ambient environment
leveraged pass it into the pool water. When heating, higher the ambient air temperature is, more free energy
can the heat pump extract and thus reach higher efficiency. At favourable conditions you pay around 15% of
se review below drawing of different ambient air conditions with subsequent
The heat pump efficiency grows by the increasing surrounding air temperature.
It takes some days to achieve the requested swimming pool water temperature. This time
heat loss and heat gain balance of your pool.
: poor pool construction, used materials, usage of cover, air
temperature relationship, fresh water refilling, filtration, etc.
: intensity of sun, winds, orientation of pool, air
In order to avoid heat loss when the swimming pool is not being used, it is highly advised to use pool’s cover.
Ideal water temperature for external pools is con
sidered at levels from 27° to 32°C. This may change based on
particular demands of the user. When setting the desired air temperature higher than 32°C please review the
material characteristics of your pool parts. High water temperature can damage these ma
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 4/ 3 6
In your hands you hold probably the most advanced and the most efficient heat pump currently available on
the market. This heat pump provides warm water in your pool at lowest possible cost. The heat pump is
strict standards and norms, in order to provide high quality
This Installation and user manual contains all the necessary information about the installation, operation and
this Installation and user manual carefully before you start to use
this product. The manufacturer is not responsible for any personal or property damage due to the improper
This Installation and user manual is an inseparable part of this product; therefore it must be kept in good
The heat pump is designed exclusively for swimming pool water heating or cooling and
maintaining its
temperature on the requested level. Other appropriate application is water temperature conditioning for fish
tanks, wine ciders or horse cooling facilities. These applications should be discussed with local installer or
The heat pump achieves the highest efficiency at 15÷35°C air temperature. At ambient air temperatures lower
15°C the efficiency of the device decreases and at the temperatures higher than +40°C the
heat pump
can get overheated which may result in its malfunction, damage or failure. Do not use the product out of the
Technical data
.
60 m
3 - HP 1400 of pool
water volume. For proper operations there must be water flow through the exchanger of the heat pump
air surrounding the swimming pool through the
carrying liquid. The air is driven by a fan through the evaporator
carrying liquid (the air is being cooled at the same tim
e). The heat-
carrying liquid is then delivered to the spirals of the exchanger by the compressor which pressurises it and thus
carrying liquid delivers its heat to the swimming pool water. From the
cooled liquid flowing to the expansion valve or capillary where its pressure decreases and
it gets cooled down rapidly at the same time. This cooled liquid flows to the evaporator again where it gets
ully automatically and is monitored by the pressure and
temperature sensors. The same principle is applied when heat pump operates in cooling mode.
Using simple language, a heat pump is able to extract the heat/cold that is present in ambient environment
and
leveraged pass it into the pool water. When heating, higher the ambient air temperature is, more free energy
can the heat pump extract and thus reach higher efficiency. At favourable conditions you pay around 15% of
se review below drawing of different ambient air conditions with subsequent
It takes some days to achieve the requested swimming pool water temperature. This time
period depends on
: poor pool construction, used materials, usage of cover, air
– water
: intensity of sun, winds, orientation of pool, air
– water temperature
In order to avoid heat loss when the swimming pool is not being used, it is highly advised to use pool’s cover.
sidered at levels from 27° to 32°C. This may change based on
particular demands of the user. When setting the desired air temperature higher than 32°C please review the
material characteristics of your pool parts. High water temperature can damage these ma
terials and contribute

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 5/ 3 6
to creation of algea. Manufacturer, distributor and reseller do not bear responsibility resulting from
inappropriate heat pump usage.
1.2
Package checking
The unit was delivered in carton box on a wooden palette. Do not accept the
signs of damage. If the package appears intact, please unpack the unit and check the content. It
should include the following:
1. The heat pump –
condensing unit, the heat exchanger
the basic parts
to see how the heat pump look
2.
This Installation and user manual
3. Four rubber silent blocks
1.3
Waste disposal information
When using this heat pump in the European countries, the following information must be
followed:
DISPOSAL:
Do not dispose this product as unsorted municipal
dispose this heat pump in domestic / household waste. It is prohibited to dispose this
appliance into forests or natural landscape. This could lead into local soil pollution.
Collection of such waste must be treated individually.
DISPOSAL POSSIBILITIES:
1.
The municipality has established a collection system where electronic waste can be disposed.
2.
When buying a new product, the retailer or the manufacturer may take back the
old appliance free of charge.
3.
Old appliance may contain va
material dealers.
4.
Disposal of packaging materials such as carton box or plastic / bubble foil can be
recycled.
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
to creation of algea. Manufacturer, distributor and reseller do not bear responsibility resulting from
Package checking
The unit was delivered in carton box on a wooden palette. Do not accept the
package if it shows
signs of damage. If the package appears intact, please unpack the unit and check the content. It
condensing unit, the heat exchanger
–
indoor unit. Please see section
to see how the heat pump look
s like
This Installation and user manual
Waste disposal information
When using this heat pump in the European countries, the following information must be
Do not dispose this product as unsorted municipal
waste. It is prohibited to
dispose this heat pump in domestic / household waste. It is prohibited to dispose this
appliance into forests or natural landscape. This could lead into local soil pollution.
Collection of such waste must be treated individually.
The municipality has established a collection system where electronic waste can be disposed.
When buying a new product, the retailer or the manufacturer may take back the
old appliance free of charge.
Old appliance may contain va
luable resources which could be sold to scrap
Disposal of packaging materials such as carton box or plastic / bubble foil can be
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
to creation of algea. Manufacturer, distributor and reseller do not bear responsibility resulting from
package if it shows
signs of damage. If the package appears intact, please unpack the unit and check the content. It
indoor unit. Please see section
3.4 Description of
When using this heat pump in the European countries, the following information must be
waste. It is prohibited to
dispose this heat pump in domestic / household waste. It is prohibited to dispose this
appliance into forests or natural landscape. This could lead into local soil pollution.
The municipality has established a collection system where electronic waste can be disposed.
When buying a new product, the retailer or the manufacturer may take back the
luable resources which could be sold to scrap
Disposal of packaging materials such as carton box or plastic / bubble foil can be

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
2.
SAFETY MEASURES
It is necessary to follow instructions in this Installation and user manual and lo
your country that regulate the installation and usage of this device. Incorrect, improper or
operations contradictory to this Installation and user manual may lead to an injury or property
damage and will lead to loss of warranty. To pre
instructions must be followed:
2.1 Electrical safety

The device operates at dangerous electrical current.

Only authorized person with particular electro
 Danger
of electrical shock.

Do not exceed the required power supply.

Do not turn the device on that shows signs of possible damage such as broken packaging, broken
or otherwise damaged unit’s chassis or cover, smoke, smell, etc.

It is necessary to use appropriate
pump to main power supply.

Do not manipulate with the device with wet hands.

Do not clean the device with water.

Before cleaning the device, switch off the circuit breaker of the unit’s pow

Installation, service or repair must be performed by qualified technician.

When the device is not intended to be used for a longer time, we recommend switching the circuit
breaker of the unit’s power supply off.

Unit must be installed in vertica
unit.

It is forbidden to install the unit close to devices that may cause electrical or frequency disturbance
such as welding machines, motors or rotors, WIFI/WLAN routers or repeaters.

It is forbidden to alter electrical installation of the device. It is also forbidden to alter any other
part or functionality of the device.
2.2
Usage precautions
Do not cover or block the intake or exhaust opening / ventilator and evaporator covers.
It is forbidden to block or cover the intake or exhaust openings with clothes, towels,
buckets, canoes, trees, etc. Such action would lead to a decrease of needed airfl
That would result in heat pump inefficiency and underperformance, eventually to heat
pump overeat with subsequent security turning off, malfunction, failure or damage.
Especially during bloom months it is highly advised to keep the evaporator fins clea

Do not climb up on or sit on the unit.

Do not place any objects on the top of the unit (e.g. boxes, flower vases, etc.).

Do not spray any flammable substances into the equipment; this might lead to fire.

Do not clean the equipment with aggressive clean
deformations.

When cleaning plastic parts do not use any cleaning agents unsuitable for plastic (household
cleaning agents, solvents, bleaching agents, benzene, diluents, rough cleaning powder, cresol,
chemical agen
ts). Instead, sweep the heat pump cover with a soft cloth or a sponge.

Never throw or insert any objects into any hose or opening.

The cover is made of metal. Do not manipulate with lighted cigarette, cigarette ashes, or any other
kind of fire in vicinity
to this part.

Use this device exclusively for the intended purpose, as described in the attached instruction
manual. Do not use parts which are not recommended.

Never block the air opening of the product. Protect the air openings from clogging by particles

Do not drink or use the condensate water drained from the unit. Do not return the water back to
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
SAFETY MEASURES
It is necessary to follow instructions in this Installation and user manual and lo
your country that regulate the installation and usage of this device. Incorrect, improper or
operations contradictory to this Installation and user manual may lead to an injury or property
damage and will lead to loss of warranty. To pre
vent injury or property damage the following
The device operates at dangerous electrical current.
Only authorized person with particular electro
-
technical qualification can manipulate with unit.
of electrical shock.
Do not exceed the required power supply.
Do not turn the device on that shows signs of possible damage such as broken packaging, broken
or otherwise damaged unit’s chassis or cover, smoke, smell, etc.
It is necessary to use appropriate
Residual current circuit breaker (RCD) for connection of the heat
pump to main power supply.
Do not manipulate with the device with wet hands.
Do not clean the device with water.
Before cleaning the device, switch off the circuit breaker of the unit’s pow
er supply.
Installation, service or repair must be performed by qualified technician.
When the device is not intended to be used for a longer time, we recommend switching the circuit
breaker of the unit’s power supply off.
Unit must be installed in vertica
l position to avoid condensate water to enter electrical part of the
It is forbidden to install the unit close to devices that may cause electrical or frequency disturbance
such as welding machines, motors or rotors, WIFI/WLAN routers or repeaters.
It is forbidden to alter electrical installation of the device. It is also forbidden to alter any other
part or functionality of the device.
Usage precautions
Do not cover or block the intake or exhaust opening / ventilator and evaporator covers.
It is forbidden to block or cover the intake or exhaust openings with clothes, towels,
buckets, canoes, trees, etc. Such action would lead to a decrease of needed airfl
That would result in heat pump inefficiency and underperformance, eventually to heat
pump overeat with subsequent security turning off, malfunction, failure or damage.
Especially during bloom months it is highly advised to keep the evaporator fins clea
Do not climb up on or sit on the unit.
Do not place any objects on the top of the unit (e.g. boxes, flower vases, etc.).
Do not spray any flammable substances into the equipment; this might lead to fire.
Do not clean the equipment with aggressive clean
ing agents, this might lead to damage or
When cleaning plastic parts do not use any cleaning agents unsuitable for plastic (household
cleaning agents, solvents, bleaching agents, benzene, diluents, rough cleaning powder, cresol,
ts). Instead, sweep the heat pump cover with a soft cloth or a sponge.
Never throw or insert any objects into any hose or opening.
The cover is made of metal. Do not manipulate with lighted cigarette, cigarette ashes, or any other
to this part.
Use this device exclusively for the intended purpose, as described in the attached instruction
manual. Do not use parts which are not recommended.
Never block the air opening of the product. Protect the air openings from clogging by particles
Do not drink or use the condensate water drained from the unit. Do not return the water back to
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 6/ 3 6
It is necessary to follow instructions in this Installation and user manual and lo
cal regulations in
your country that regulate the installation and usage of this device. Incorrect, improper or
operations contradictory to this Installation and user manual may lead to an injury or property
vent injury or property damage the following
technical qualification can manipulate with unit.
Do not turn the device on that shows signs of possible damage such as broken packaging, broken
Residual current circuit breaker (RCD) for connection of the heat
er supply.
When the device is not intended to be used for a longer time, we recommend switching the circuit
l position to avoid condensate water to enter electrical part of the
It is forbidden to install the unit close to devices that may cause electrical or frequency disturbance
It is forbidden to alter electrical installation of the device. It is also forbidden to alter any other
Do not cover or block the intake or exhaust opening / ventilator and evaporator covers.
It is forbidden to block or cover the intake or exhaust openings with clothes, towels,
buckets, canoes, trees, etc. Such action would lead to a decrease of needed airfl
ow.
That would result in heat pump inefficiency and underperformance, eventually to heat
pump overeat with subsequent security turning off, malfunction, failure or damage.
Especially during bloom months it is highly advised to keep the evaporator fins clea
n.
Do not spray any flammable substances into the equipment; this might lead to fire.
ing agents, this might lead to damage or
When cleaning plastic parts do not use any cleaning agents unsuitable for plastic (household
cleaning agents, solvents, bleaching agents, benzene, diluents, rough cleaning powder, cresol,
ts). Instead, sweep the heat pump cover with a soft cloth or a sponge.
The cover is made of metal. Do not manipulate with lighted cigarette, cigarette ashes, or any other
Use this device exclusively for the intended purpose, as described in the attached instruction
Never block the air opening of the product. Protect the air openings from clogging by particles
.
Do not drink or use the condensate water drained from the unit. Do not return the water back to

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 7/ 3 6
the swimming pool. The water may be contaminated with bacteria.

Children are not allowed to operate, touch or play with the unit.

Children are not allowed to

Prevent the children from injury or harm caused by any manipulation with the unit, its parts or its
packaging. Small parts like screws may be swallowed and cause harm to health.
 Do not
leave the children in the swimming pool / at the swimming pool unattended.

The positioning of the heat pump must be in accordance with the STN 33 2000
it must be placed at least 3,5 m from the swimming pool´s external border.
 For heat
ing/cooling the swimming pool by the heat pump, the filtration pump must run and the
water must flow through the heat exchanger.

Never turn on the heat pump if it is without water and if the filtration device is not operating.

Protect the heat pump from
pump’s water heat exchanger and prepare the product for the winter time.
 At
low surrounding ambient temperature level (below 10°C) and high relative air humidity level
(e.g. after rain, d
uring the night, etc.), the evaporator may get iced up. Heat pump will
automatically defreeze itself. Its operations or functionality is not harmed but the efficiency
decreases.

Manufacturer does not bear any responsibility concenring damages caused by ina
pump selection, installation or application.

Do not pressurize the water heat exchanger higher than 0.25MPa (2.5bar). By pressure of 0.5MPa
(5bar) the water heat exchanger gets irreversibly damaged. It is advised to install a security valv
with pressure threshold at 0.25MPa (2.5Bar) before the heat exchanger.

Do not apply or use water of higher temperature than 45°C in water heat exchanger. Water
temperature above 60°C irreversibly damages the water heat exchanger.
 Manufacturer does not
bear any responsibility concerning damages caused by inappropriate heat
pump performance and/or model selection, installation or application. Heat pump is considered
undersized in the case it works usually and in long
warranty void applies for damages on the device or other damages if the device works usually in
long-
term more than 18 hours daily.

The heat pump must be correctly sized for its application.

Refrigerant connection between the water and the condensing unit must comply with local
refrigerant regulations. Typically, the refrigerant circuit must be sealed. Manufacturer does not
bear any responsibility for damages caused by incorrect refrigerant wo
Warning
a. The WARNING sign
practice, or the like, which, if not correctly performed or adhered to,
could result in personal injury or injury to a third party. These signs are
rare, but are extremely important.
a.
Keep the heat pump away from fire source.
b.
It must be placed in well ventilated area, indoor or closed area is not allowed.
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
the swimming pool. The water may be contaminated with bacteria.
Children are not allowed to operate, touch or play with the unit.
Children are not allowed to
manipulate with packaging, plastic / bubble foil. Risk of suffocation!
Prevent the children from injury or harm caused by any manipulation with the unit, its parts or its
packaging. Small parts like screws may be swallowed and cause harm to health.
leave the children in the swimming pool / at the swimming pool unattended.
The positioning of the heat pump must be in accordance with the STN 33 2000
-
it must be placed at least 3,5 m from the swimming pool´s external border.
ing/cooling the swimming pool by the heat pump, the filtration pump must run and the
water must flow through the heat exchanger.
Never turn on the heat pump if it is without water and if the filtration device is not operating.
Protect the heat pump from
freezing. Eliminate the water from the filtration and from the heat
pump’s water heat exchanger and prepare the product for the winter time.
low surrounding ambient temperature level (below 10°C) and high relative air humidity level
uring the night, etc.), the evaporator may get iced up. Heat pump will
automatically defreeze itself. Its operations or functionality is not harmed but the efficiency
Manufacturer does not bear any responsibility concenring damages caused by ina
pump selection, installation or application.
Do not pressurize the water heat exchanger higher than 0.25MPa (2.5bar). By pressure of 0.5MPa
(5bar) the water heat exchanger gets irreversibly damaged. It is advised to install a security valv
with pressure threshold at 0.25MPa (2.5Bar) before the heat exchanger.
Do not apply or use water of higher temperature than 45°C in water heat exchanger. Water
temperature above 60°C irreversibly damages the water heat exchanger.
bear any responsibility concerning damages caused by inappropriate heat
pump performance and/or model selection, installation or application. Heat pump is considered
undersized in the case it works usually and in long
-
term more than 18 hours daily. General
warranty void applies for damages on the device or other damages if the device works usually in
term more than 18 hours daily.
The heat pump must be correctly sized for its application.
Refrigerant connection between the water and the condensing unit must comply with local
refrigerant regulations. Typically, the refrigerant circuit must be sealed. Manufacturer does not
bear any responsibility for damages caused by incorrect refrigerant wo
rks.
a. The WARNING sign
denotes a hazard. It calls attention to a procedure,
practice, or the like, which, if not correctly performed or adhered to,
could result in personal injury or injury to a third party. These signs are
rare, but are extremely important.
Keep the heat pump away from fire source.
It must be placed in well ventilated area, indoor or closed area is not allowed.
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
manipulate with packaging, plastic / bubble foil. Risk of suffocation!
Prevent the children from injury or harm caused by any manipulation with the unit, its parts or its
packaging. Small parts like screws may be swallowed and cause harm to health.
leave the children in the swimming pool / at the swimming pool unattended.
-
7-702 standard, i.e.
ing/cooling the swimming pool by the heat pump, the filtration pump must run and the
Never turn on the heat pump if it is without water and if the filtration device is not operating.
freezing. Eliminate the water from the filtration and from the heat
low surrounding ambient temperature level (below 10°C) and high relative air humidity level
uring the night, etc.), the evaporator may get iced up. Heat pump will
automatically defreeze itself. Its operations or functionality is not harmed but the efficiency
Manufacturer does not bear any responsibility concenring damages caused by ina
ppropriate heat
Do not pressurize the water heat exchanger higher than 0.25MPa (2.5bar). By pressure of 0.5MPa
(5bar) the water heat exchanger gets irreversibly damaged. It is advised to install a security valv
e
Do not apply or use water of higher temperature than 45°C in water heat exchanger. Water
bear any responsibility concerning damages caused by inappropriate heat
pump performance and/or model selection, installation or application. Heat pump is considered
term more than 18 hours daily. General
warranty void applies for damages on the device or other damages if the device works usually in
Refrigerant connection between the water and the condensing unit must comply with local
refrigerant regulations. Typically, the refrigerant circuit must be sealed. Manufacturer does not
denotes a hazard. It calls attention to a procedure,
practice, or the like, which, if not correctly performed or adhered to,
could result in personal injury or injury to a third party. These signs are
It must be placed in well ventilated area, indoor or closed area is not allowed.

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
c.
Repair and
d.
Vacuumize completely before welding. Welding can only be carried out by
professional personnel in service center.
1） Attention
a.
Please read the following instructions before installation, use and
b.
Installation must be done by professional staff only in accordance with this manual.
c.
A leakage test must be performed after installation.
d.
If a repair is required, please contact the nearest after
strictly in accordance with manual. All repair practice by non
e.
Set proper temperature in order to get comfortable water temperature to avoid overheating or
overcooling.
f.
Please don’t stack substances, which will block air flow
efficiency of the heater will be reduced or even stopped.
g.
Don’t use or stock combustible gas or liquid such as thinners, paint and fuel to avoid fire.
h.
In order to optimize the heating effect, please install heat
swimming pool and the heater, and please use a recommended cover on the swimming pool.
i.
Connecting pipes of the swimming pool and the heater should be
2） Safety
a.
Please keep the main power supply switch far away from the children.
b.
When a power cut happens during operating, and later the power is restored, the heater will start up.
c.
Please switch off the main power suppl
damage that caused by lightning;
d.
Any repairing should be conducted in the area with good ventilation. The ignition source is prohibited
during the inspection.
e.
Safety inspection must be carried befor
order to minimize the risk.
f.
If R32 gas leaks during the installation process, all operations must be stopped immediately and call
the service center.
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
Repair and
disposal must be carried out by trained service personnel
Vacuumize completely before welding. Welding can only be carried out by
professional personnel in service center.
Please read the following instructions before installation, use and
maintenance.
Installation must be done by professional staff only in accordance with this manual.
A leakage test must be performed after installation.
If a repair is required, please contact the nearest after
-
sales service center. The repair process must b
strictly in accordance with manual. All repair practice by non
-
professional is prohibited.
Set proper temperature in order to get comfortable water temperature to avoid overheating or
Please don’t stack substances, which will block air flow
near inlet or outlet area, otherwise the
efficiency of the heater will be reduced or even stopped.
Don’t use or stock combustible gas or liquid such as thinners, paint and fuel to avoid fire.
In order to optimize the heating effect, please install heat
preservation insulation on pipes between
swimming pool and the heater, and please use a recommended cover on the swimming pool.
Connecting pipes of the swimming pool and the heater should be
≤10m.
Please keep the main power supply switch far away from the children.
When a power cut happens during operating, and later the power is restored, the heater will start up.
Please switch off the main power suppl
y in lightening and storm weather to prevent from machine
damage that caused by lightning;
Any repairing should be conducted in the area with good ventilation. The ignition source is prohibited
Safety inspection must be carried befor
e the maintenance or repair for heat pumps with R32 gas in
If R32 gas leaks during the installation process, all operations must be stopped immediately and call
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 8/ 3 6
disposal must be carried out by trained service personnel
Vacuumize completely before welding. Welding can only be carried out by
Installation must be done by professional staff only in accordance with this manual.
sales service center. The repair process must b
e
professional is prohibited.
Set proper temperature in order to get comfortable water temperature to avoid overheating or
near inlet or outlet area, otherwise the
Don’t use or stock combustible gas or liquid such as thinners, paint and fuel to avoid fire.
preservation insulation on pipes between
swimming pool and the heater, and please use a recommended cover on the swimming pool.
When a power cut happens during operating, and later the power is restored, the heater will start up.
y in lightening and storm weather to prevent from machine
Any repairing should be conducted in the area with good ventilation. The ignition source is prohibited
e the maintenance or repair for heat pumps with R32 gas in
If R32 gas leaks during the installation process, all operations must be stopped immediately and call

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 9/ 3 6
2.3
Handling precautions
 Leave
the condensing unit in vertical upright position for at least 2 hours before the installation.

Transport in lying position or turning the device over may harm the compressor resulting in unit’s
malfunction, failure or damage and will lead to loss of warran

The device must be handled with care and special attention avoiding any mechanical damage.

It is forbidden to apply any improper mechanical force onto the unit. This may cause mechanical
damage to the device.

It is forbidden to let the device fall freely onto the ground or any solid surface resulting in hard
impact.

Please notify your reseller or distributor if you suspect that the unit was delivered damaged. Unit
may seem to work well at start but small damag
In such case the unit must be inspected and approved for further use by your reseller.

Please notify your reseller or distributor if directly after installation you suspect that unit is not
working in perfect order.

In the case of device failure resulting from improper handling or mechanical damage (impact, hit,
fall, etc.), the manufacturer reserves the right to evaluate the continuity of warranty.
2.4 Transportation
a. Always keep upright
b. Do not lift the water union
( If so, the titanium heat exchanger
inside the heat pump may be damaged)
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
Handling precautions
the condensing unit in vertical upright position for at least 2 hours before the installation.
Transport in lying position or turning the device over may harm the compressor resulting in unit’s
malfunction, failure or damage and will lead to loss of warran
ty.
The device must be handled with care and special attention avoiding any mechanical damage.
It is forbidden to apply any improper mechanical force onto the unit. This may cause mechanical
It is forbidden to let the device fall freely onto the ground or any solid surface resulting in hard
Please notify your reseller or distributor if you suspect that the unit was delivered damaged. Unit
may seem to work well at start but small damag
e can make the unit go out-
of
In such case the unit must be inspected and approved for further use by your reseller.
Please notify your reseller or distributor if directly after installation you suspect that unit is not
In the case of device failure resulting from improper handling or mechanical damage (impact, hit,
fall, etc.), the manufacturer reserves the right to evaluate the continuity of warranty.
( If so, the titanium heat exchanger
inside the heat pump may be damaged)
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
the condensing unit in vertical upright position for at least 2 hours before the installation.
Transport in lying position or turning the device over may harm the compressor resulting in unit’s
The device must be handled with care and special attention avoiding any mechanical damage.
It is forbidden to apply any improper mechanical force onto the unit. This may cause mechanical
It is forbidden to let the device fall freely onto the ground or any solid surface resulting in hard
Please notify your reseller or distributor if you suspect that the unit was delivered damaged. Unit
of
-order in short time.
In such case the unit must be inspected and approved for further use by your reseller.
Please notify your reseller or distributor if directly after installation you suspect that unit is not
In the case of device failure resulting from improper handling or mechanical damage (impact, hit,
fall, etc.), the manufacturer reserves the right to evaluate the continuity of warranty.

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
3.
TECHNICAL SPECIFICATION
3.1 Technical data
Model
PERFORMANCE CONDITION: Air 27°C/
Heating capacity (kW)
COP Range
PERFORMANCE CONDITION: Air 15°C/ Water 26°C/ Humid. 70%
Heating capacity (kW)
COP Range
PERFORMANCE CONDITION: Air 35°C/
Cooling capacity (kW)
TECHNICAL SPECIFICATIONS
Advised pool volume (m3) *
Operating air temperature (℃
)
Rated input power (kW)
Rated input current (A)
Maximum input current (A)
Power cord（mm²）
Sound level at 10m dB(A)
Advised water flow (m³/h)
Water connection (mm)
Compressor
Fan
Expansion
Casing
Heat exchanger
Winter accessories
WIFI
* The manufacturer reserves the right to change the parameters without notice.
** In the case Winter module, condensate tray antifreeze or heat exchanger frost protection is installed.
The refrigera
nt circuit is filled with R32.
Refrigerant R32 also called HFC-
32 or difluoromethane. R32 is a molecule used as refrigerant that has zero
ozone depletion potential (ODP).
R32 with the global warming potential (GWP) index 675 times that of carbon dioxide, b
frame, and it is classified as A2L -
slightly flammable by ASHRAE.
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
TECHNICAL SPECIFICATION
HP1
1
00 GREEN INVERTER
PRO
HP1
5
00 GREEN INVERTER
PERFORMANCE CONDITION: Air 27°C/
Water 27°C/ Humid. 80%
10.8
14~6.4
PERFORMANCE CONDITION: Air 15°C/ Water 26°C/ Humid. 70%
7.7
7.5~4.5
PERFORMANCE CONDITION: Air 35°C/
Water 28°C/ Humid. 80%
Cooling capacity (kW)
4.5
30~40
)
-15℃~43℃
0.20~1.71
0.87~7.4
10
3X2.5
18.1~29.4
3~5
50
Full Stepless DC inverter compressor
DC
Inverter
EEV
ABS UV resistant on a
metal chassis
Titanium Grade 2 ASTM B338M, twisted tube in plastic
body
Winter module (compressor heater
condensate heater
45W
Standard worldwide, IEEE802.11 b/g/n;
2,412 -
2,484 GHz
* The manufacturer reserves the right to change the parameters without notice.
** In the case Winter module, condensate tray antifreeze or heat exchanger frost protection is installed.
nt circuit is filled with R32.
32 or difluoromethane. R32 is a molecule used as refrigerant that has zero
R32 with the global warming potential (GWP) index 675 times that of carbon dioxide, b
ased on a 100
slightly flammable by ASHRAE.
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 1 0 / 3 6
00 GREEN INVERTER
PRO
15
15~6.6
10.5
7.7~4.6
6.7
40~60
0.27~2.28
1.17~9.91
13.5
3X2.5
20.8~24.5
5~7
Full Stepless DC inverter compressor
metal chassis
Titanium Grade 2 ASTM B338M, twisted tube in plastic
Winter module (compressor heater
30W
) and
Goldfin
45W
Standard worldwide, IEEE802.11 b/g/n;
2,484 GHz
** In the case Winter module, condensate tray antifreeze or heat exchanger frost protection is installed.
32 or difluoromethane. R32 is a molecule used as refrigerant that has zero
ased on a 100
-year time

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 1 1 / 3 6
Operating condition and range:
a.
Air temperature operating range
b.
Heating temperature setting range: 18
c.
Cooing temperature setting range: 12
The heat pump will have ideal performance in the operation range Air 15
Introduction of different modes:
Th
e heat pump has two modes:
conditions.
3.2
Swimming pool water parameters
The heat pump is designed for heating the swimming pool water. Although the water heat exchanger is made
from the most durable titanium, in order to ensure
be in accordance with the related sanitary requirements.
The limit values for the heat pump operation are the following:
-
pH value ranging from 6.8 to 7.9,
-
total chlorine amount not exceeding 3 mg/
- salt content 6% wt/wt.
Should you have different values of pH, chlorine or salt please try to apply appropriate agents or contact your
swimming pool builder to resolve the situation. Above mentioned values are recommended for pools in
general.
It is als
o advised to keep the water hardness on the lower limit of the optimal range, i.e. closely above 8 °N.
Mode
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
Air temperature operating range
: -15℃～43℃
Heating temperature setting range: 18
℃～40℃
Cooing temperature setting range: 12
℃～30℃
The heat pump will have ideal performance in the operation range Air 15
℃～
25
e heat pump has two modes:
Max and Silent.
They have different strengths under different
Swimming pool water parameters
The heat pump is designed for heating the swimming pool water. Although the water heat exchanger is made
from the most durable titanium, in order to ensure
long term reliability of the heat pump the pool water must
be in accordance with the related sanitary requirements.
The limit values for the heat pump operation are the following:
pH value ranging from 6.8 to 7.9,
total chlorine amount not exceeding 3 mg/
l,
Should you have different values of pH, chlorine or salt please try to apply appropriate agents or contact your
swimming pool builder to resolve the situation. Above mentioned values are recommended for pools in
o advised to keep the water hardness on the lower limit of the optimal range, i.e. closely above 8 °N.
Modes
Strength
Max mode
Heating capacity: 20% to 100% capacity
Intelligent optimization
Fast heating
Silent mode Heating capacity: 20% to
65
Silent Heating
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
25
℃
They have different strengths under different
The heat pump is designed for heating the swimming pool water. Although the water heat exchanger is made
long term reliability of the heat pump the pool water must
Should you have different values of pH, chlorine or salt please try to apply appropriate agents or contact your
swimming pool builder to resolve the situation. Above mentioned values are recommended for pools in
o advised to keep the water hardness on the lower limit of the optimal range, i.e. closely above 8 °N.
Strength
Heating capacity: 20% to 100% capacity
65
% capacity

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
3.3
Heat pump dimensions
3.4
Description of the basic parts
CONDENSING UNIT
Legend: 1 –
Protecting grates of the
2 – Cover / ABS
chassis
3 – Control panel
4 –
Valve for refilling the refrigerant (under the cover)
5 –
Power supply connection (underneath the plastic cover)
6 –
Evaporator (air inlet)
7 –
Water outlet connection hub
8 –
Water inlet connection hub
*-
in cooling mode applies in reversed order
HP1
1
00 GREEN
INVERTER PRO
HP1
5
00
GREEN
INVERTER PRO
Note:
The illustrations and descriptions found in this Installation and user manual are not binding. The
manufacturer reserves the right to make corrections or changes without notice.
2
1
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
Heat pump dimensions
Description of the basic parts
Protecting grates of the
fan(air outlet)/ventilator cover
chassis
Valve for refilling the refrigerant (under the cover)
Power supply connection (underneath the plastic cover)
Evaporator (air inlet)
Water outlet connection hub
Water inlet connection hub
in cooling mode applies in reversed order
A B C D E F
315 590 302 340 990 290
315 590 302 340 990 340
The illustrations and descriptions found in this Installation and user manual are not binding. The
manufacturer reserves the right to make corrections or changes without notice.
3
4
5
7
8
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 1 2 / 3 6
G H
74 657
74 657
The illustrations and descriptions found in this Installation and user manual are not binding. The
6

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 1 3 / 3 6
3.5
Installation reminder
Only a
professional staff is allowed to install the heat pump. The users are not qualified to
install by themselves, otherwise the heat pump might be damaged and risky for users’ safety.
Location and dimension
The pool heat pump should be installed in a good ventilation place.
1) The frame must be fixed by bolts (M10) to concrete foundation or brackets. The
foundation must be solid and fastened; the bracket must be strong enough and antirust treate
2) Please don’t stack substances that will block air flow near inlet or outlet area, and there is no
barrier within 50cm behind and 250cm in front of the machine, or the efficiency of the heater
will be reduced or even stopped;
3) The machine needs an a
ppended pump (Supplied by the user). The recommended pump
specification-
flux: refer to Technical Parameter, Max. lift
4) When the machine is running, there will be condensation water discharged from the bottom,
please pay attention to it. Please hol
well, and then connect a pipe to drain the condensation water out.
The inlet and outlet water unions can’t stand the weight of soft pipes. The heat pump must be
connected with hard pipes!
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
Installation reminder
professional staff is allowed to install the heat pump. The users are not qualified to
install by themselves, otherwise the heat pump might be damaged and risky for users’ safety.
The pool heat pump should be installed in a good ventilation place.
1) The frame must be fixed by bolts (M10) to concrete foundation or brackets. The
foundation must be solid and fastened; the bracket must be strong enough and antirust treate
2) Please don’t stack substances that will block air flow near inlet or outlet area, and there is no
barrier within 50cm behind and 250cm in front of the machine, or the efficiency of the heater
will be reduced or even stopped;
ppended pump (Supplied by the user). The recommended pump
flux: refer to Technical Parameter, Max. lift
≥10m;
4) When the machine is running, there will be condensation water discharged from the bottom,
please pay attention to it. Please hol
d the drainage nozzle (accessory) into the hole and clip it
well, and then connect a pipe to drain the condensation water out.
The inlet and outlet water unions can’t stand the weight of soft pipes. The heat pump must be
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
professional staff is allowed to install the heat pump. The users are not qualified to
install by themselves, otherwise the heat pump might be damaged and risky for users’ safety.
1) The frame must be fixed by bolts (M10) to concrete foundation or brackets. The
concrete
foundation must be solid and fastened; the bracket must be strong enough and antirust treate
d;
2) Please don’t stack substances that will block air flow near inlet or outlet area, and there is no
barrier within 50cm behind and 250cm in front of the machine, or the efficiency of the heater
ppended pump (Supplied by the user). The recommended pump
4) When the machine is running, there will be condensation water discharged from the bottom,
d the drainage nozzle (accessory) into the hole and clip it
The inlet and outlet water unions can’t stand the weight of soft pipes. The heat pump must be

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
3.6 Accessories
Features

Stepless DC inverter compressor
 EEV Technology

Quick hot gas defrosting with 4
 High-
efficiency twisted titanium heat exchanger

High pressure and low pressure protection

Soft start & wide voltage application

Stable inverter control system
3.7
Electric wiring Diagram

Connect to appropriate power supply, the voltage should comply with the rated voltage
of the products.
 Earth the
machine well.

Wiring must be handled by a professional technician according to the circuit diagram.

Set leakage protector according to the local code for wiring (leakage operating current
30mA).

The layout of power cable and signal cable should be orderl
other.
Electric wiring Diagram -
For power supply: 230V 50Hz
Power Supply
230V 50Hz
Earthing
Distribution Box(Customer prepare)
Breaker
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
Stepless DC inverter compressor
Quick hot gas defrosting with 4
-way valve
efficiency twisted titanium heat exchanger
High pressure and low pressure protection
Soft start & wide voltage application
Stable inverter control system
Electric wiring Diagram
Connect to appropriate power supply, the voltage should comply with the rated voltage
machine well.
Wiring must be handled by a professional technician according to the circuit diagram.
Set leakage protector according to the local code for wiring (leakage operating current
The layout of power cable and signal cable should be orderl
y and not affecting each
For power supply: 230V 50Hz
Distribution Box(Customer prepare)
Power Cord
Swimming Pool Heat Pump Wiring Board
Fuse
Breaker
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 1 4 / 3 6
Connect to appropriate power supply, the voltage should comply with the rated voltage
Wiring must be handled by a professional technician according to the circuit diagram.
Set leakage protector according to the local code for wiring (leakage operating current
≤
y and not affecting each
Swimming Pool Heat Pump Wiring Board

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 1 5 / 3 6
Reference for protecting devices and cable specification
※
Above data is subject to modification without notice.
Note:
The above data is adapted to power cord
be increased. The signal cable can be extended to 50m maximumly.
MODEL
Breaker
Rated Current (A)
Rated Residual Action Current mA
Fuse (A)
Power Cord (mm
Signal cable（
mm2
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
Reference for protecting devices and cable specification
Above data is subject to modification without notice.
The above data is adapted to power cord
≤ 10m. If power cord is＞
10m, wire diameter must
be increased. The signal cable can be extended to 50m maximumly.
HP
11
00 GREEN
INVERTER PRO
HP1
5
00 GREEN
INVERTER PRO
Rated Current (A)
12.0 17.0
Rated Residual Action Current mA
30 30
12.0
17.0
Power Cord (mm
2
) 3×2.5
3×2.5
mm2
） 3×0.5
3×0.5
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
10m, wire diameter must
00 GREEN
INVERTER PRO
3×2.5
3×0.5

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
Water pump connection
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 1 6 / 3 6

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 1 7 / 3 6
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 1 8 / 3 6

H P 1 1 0 0 / 1 5 0 0 GREEN INVERTER Pro
P a g e 1 9 / 3 6
Water pump control and timer connection
2: Water pump wiring of Heat Pump
Note: The installer should connect 1 parallel with 2 (as above picture). To start the water
pump, condition 1 or 2 is connected. To stop the water pump, both 1 and 2 should be
disconnected.
I n s t a l l a t i o n a n d u s e r
V e r s i o n :
Water pump control and timer connection
1: Water pump timer
2: Water pump wiring of Heat Pump
Note: The installer should connect 1 parallel with 2 (as above picture). To start the water
pump, condition 1 or 2 is connected. To stop the water pump, both 1 and 2 should be
I n s t a l l a t i o n a n d u s e r
m a n u a l
V e r s i o n :
05/2020
H E A T P U M P
M I C R O W E L L H P
Note: The installer should connect 1 parallel with 2 (as above picture). To start the water
pump, condition 1 or 2 is connected. To stop the water pump, both 1 and 2 should be

I n s t a l l a t i o n a n d u s e r m a n u a l
V e r s i o n : 0 5 / 2 0 2 0
H E A T P U M P
M I C R O W E L L H P
4. REGULATION
4.1
Description of the LCD panel
Symbol
Designation
ON/OFF
Unlock/Heating&
Cooling selection
Speed Mode
UP/DOWN
Attention:
a. Standby mode or Screen lock
：
b. Power off： Only
light up
c. The controller has power-
saving function.
I n s t a l l a t i o n a n d u s e r m a n u a l
H P 1 1 0 0 / 1 5 0 0
Description of the LCD panel
Designation
Function
ON/OFF
Power On/Off
Wifi setting
Unlock/Heating&
Cooling selection
Automatic heating& cooling mode
Heating Mode
Cooling Mode
Lock/Unlock Screen
Speed Mode
Two modes for switching( Max
UP/DOWN
Temperature Setting & Displaying
：
Only
light up, screen and other buttons turn dark.
light up
，No display on screen.
saving function.
H P 1 1 0 0 / 1 5 0 0
GREEN INVERTER Pro
P a g e 2 0 / 3 6
Automatic heating& cooling mode
, Silence )
Temperature Setting & Displaying
light up, screen and other buttons turn dark.