Midwest Manufacturing DAKOTA CLOSET 290-5347 User manual

DAKOTA CLOSET
SKU #290-5347, 5348, 5349
101" W x 86-1/2" H x 25-1/2"
MATERIALS
PRODUCT QTY
86-1/2" Upright 6
12" Shelf - 2 Pack 4
24" Shelf - 2 Pack 11
24" x 5" Drawer Fronts 4
24" x 5" Drawer Hardware Kit 4
Soft-Close Drawer Attachment 4
Corner H-Bracket - 3 Pack 3
24" Closet Rod - 2 pack 1
Rev-A-Shelf 24" Pull-Out Basket 2
Rev-A-Shelf 14" Valet Rod 1
Rev-A-Shelf 14" Pull-Out Tie Rack 1
Rev-A-Shelf 14" Pull-Out Belt Rack 1
Closet L-Bracket 3
Cabinet Knob 4
12"24"
24"
24"
24"
*Actual width for 12" shelf is 11-5/8"

Start by marking the wood studs in the location your
project will be installed. Using the stud finder, pencil
and tape measure, find and mark the wall studs.
STEP 1 STEP 2
TOOLS NEEDED
-Pencil -Tape Measure -Phillips Head Screwdriver -Stud Finder -Level -Electric Drill -Rubber Mallet
Using a screwdriver, install the cam dowels from the
cam lock pack included with your shelves into all of
the uprights. Use the notes below for location of the
shelves counting holes from the bottom. All shelves
are adjustable and can be moved if desired.
5555
17 17
29 29 29 29
39 39
50 50
60 60 60 60
69 69 69 69
*Notch covers base moulding

STEP 3
Align the cam locks from the cam lock pack over the
pre-drilled holes in the shelves, making sure the open
ends match up. Firmly press the cam locks into the
holes. Cam locks cannot be removed once installed,
ensure proper orientation using illustrations below.
Use a rubber mallet to tap in if needed.
STEP 4
Lower the shelves with installed cam locks onto the
installed cam dowels installed in the uprights. Once
seated, secure the shelves with a screwdriver by turning
the cam lock a quarter-turn in the clockwise direction.
The cam locks are designed to be turned with the
screwdriver at a slight angle as to avoid hitting your
knuckles on the vertical panel.

STEP 5 STEP 6
Secure your project to the wall safely with L-Brackets.
Install L-Brackets into the top shelf and into the
previously marked wall studs. If you are unable
to install into the wall stud, use the included
drywall anchors.
Using the included screws, install the Corner H-Brackets
onto the left end of the shelving on the long section
of the closet. Install shelf and bracket by clipping the
bracket into WALL B and lowering the shelf onto the
installed cam dowels of the upright in WALL A.
WALL B
WALL B
WALL A
WALL A

STEP 7 STEP 8
Install the wardrobe rod supports into the pre-drilled
holes in the uprights. Insert the wardrobe rod into the
wardrobe rod supports. Supports are designed to be
adjustable and can be moved to any height desired.
Install the drawers following the included instructions
in the drawer hardware kit.

STEP 9 STEP 10
Install the Valet Rod using the provided fasteners into
any of the rows of holes in your upright that you desire.
Install the Pull-Out Rack using the provided fasteners
into any of the rows of holes in your upright that
you desire.

STEP 11
Position basket slide where desired in closet. Align
front of slide with front of closet upright. (Fig. 1)
Align system holes of slide to the holes of the upright
and attach 5 mm euro screws. Repeat for the other
side. Place back of wire basket into hook on left
and right sides. (Fig. 2) Lower the basket down so
the tabs on the basket are inserted into the slots on
the slides. (Fig. 3)