miGuard PMR1 User manual

INSTRUCTIONS
PMR1
lines open 0900 to 1700 Monday to Friday
“ whatever your question, we’re just a phone call away “
0345 257 1000
miGuard Customer Helpline
Wirefree PIR, Magnetic Sensor
& Remote Control
Accessory Pack

Congratulations on your purchase of the
miGuard Accessory Pack
1 x Pet Friendly PIR Motion Sensor
1 x Door/Window Magnetic Sensor
1 x Remote Control
All Batteries and Fixings
Instructions
a. Read the instructions thoroughly
b. Remove all the contents from their packaging
c. Consider the most appropriate positioning
of each Accessory
d. Avoid mounting Sensors near metal objects or
electrical wiring
Before Installation:
Features
Two Lens PIR : pet tolerant to 25 kgs, with a vertical
and horizontal detection range of 110°
Digital dual-core fuzzy logic control chip and
intelligent analysis: effectively identifies signal
interference and body movement.
Automatic temperature compensation and anti-air
turbulence technology/control: automatically adapts
to environmental changes, thereby saving energy.
Automatic SMS notification of a low battery condition
when connected to a miGuard GSM Alarm System.
LED Indication
Flashes every 2 seconds: self-testing state
Flashes twice: self-testing is finished, enters working
mode
Flashes once: movement is detected
Flashes once every 3 seconds: low battery indication,
(immediate battery change recommended).
If the PIR is connected to a miGuard GSM Alarm
System, an SMS alert will automatically be sent to the
registered user.
Installation
Avoid mounting the Sensor in areas where draughts
may be present or where the temperature may
fluctuate greatly, such as near to: windows, air
conditioning, heating, refrigeration units, cooking
appliances and direct sunlight.
Where possible, mount the Sensor in the corner of
the room so that the logical path of an intruder
would cut across the fan detection pattern (see
diagrams overleaf). A PIR responds more effectively
to movement across the device than to movement
directly towards it.
PCB Layout
Test Mode
PACK CONTENTS
1. PIR MOTION SENSOR
Appearance
1.Detection Window
2.LED Indicator
3.Adjustable Bracket
3
Infrared Sensor: Detects movement and triggers
alarm signal when the system is armed.
Tamper Switch: If the casing is opened when in
‘working state’ the tamper switch will be triggered
and generate an alarm signal.
Working Mode
1. Remove the activation strip. Fit the retaining screw
supplied.
2. Self-testing will commence for 1 minute, indicated
by the LED flashing every 2 seconds.
3. To enter Test Mode press the Test Button at the
back of the PIR. The LED will then flash once
when movement is detected, for up to 3 minutes.
Test Button
1. To test in Working Mode, walk in front of the Sensor
- the LED should illuminate once when movement
is detected.
2. If the Sensor is triggered twice in 3 minutes it will
enter into power saving (sleep mode). If no
movement is detected within the next 3 minutes,
the Sensor will return to normal working mode.

4. Fit the Sensor in a position that will cover your
desired protection area:
a. Fix the bracket to the wall with the fixings kit
supplied. For optimum performance set the
the height of the bracket to 2 metres above
ground level.
b. Adjust angle of the PIR Sensor to cover the
required detection area.
PIR Installation continued…
5. To test, walk in front of the Sensor - the LED
should illuminate once when movement is
detected. If the Sensor is triggered twice in 3
minutes, it will enter into power saving (sleep
mode). If no movement is detected within the
next 3 minutes, the Sensor will return to normal
working mode.
Features
The Sensor can be fitted to doors, windows, and
any other object that opens and closes.
Transmits a signal to the Control Panel/Siren when
contact is broken.
Transmitter Magnet
LED Indicator
Appearance
LED Indication
Flashes once: door/window opened, transmitter
sends signal to the Control Panel/Siren
Flashes rapidly: low battery indication, (immediate
battery change recommended)
2. DOOR/WINDOW SENSOR
Top view Side
2m
Ground
Power Supply DC 3V (AA 1.5V LR6 Battery x 2)
Static Current ≤ 90uA
Alarm Current ≤ 9.5mA
Detection Area 8m/110°
Transmitting Distance ≤80m ﴾in open area﴿
Pet Immunity ≤ 25kg
Radio Frequency 433 MHz
Housing Material ABS Plastic
Operating Temperature -10°C~50°C
Relative Humidity ≤ 80% ﴾non‐condensing﴿
PIR Sensor Dimensions
(L x W x D) 108 x 52 x 36.8 mm
Bracket Dimensions
(L x W x D) 52 x 30 x 26.5 mm
Specification

The Remote Control enables you to quickly and
conveniently Arm and Disarm your Alarm System.
In the event of an emergency when in or near your
property, pressing the SOS button will trigger an
alarm condition on the Control Panel/Siren.
Features
LED Indication
Flashes once: transmits the signal
Low Light Level: low battery indication, (immediate
battery change recommended)
Appearance
Specification
Buttons/Functions
See over.
LED Indicator
Panic
Disarm
Part Arm
(Home Mode)
Arm
Keyring Clasp
Power Supply DC3V CR2025 Lithium Battery
Transmitting Distance ≤80m ﴾in open area﴿
Radio Frequency 433 MHz
Housing Material ABS Plastic
Operating Temperature -10°C~50°C
Relative Humidity ≤ 80% ﴾non‐condensing﴿
Dimensions (L x W x D) 58 x 31 x 9.5mm
PCB Layout
AA 1.5V
Tamper
Zone
Installation
Specification
-10°C~55°C
DC 1.5V (AA 1.5V LR6 Battery x 1pc)
433MHz
≤ 30uA ≤ 40mA
≤80m ﴾in open area﴿
71 x 34 x 17.5mm
51 x 12 x 13.5mm
Power Supply
Static Current Alarm Current
Transmitting Distance
Radio Frequency
Housing Material ABS Plastic
Operating Temperature
Relative Humidity
Sensor Dimensions (LxWxD)
Magnet Dimensions (LxWxD)
≤ 80% ﴾non‐condensing﴿
3. REMOTE CONTROL
LED
LED
1. Remove the activation strip from the battery
compartment.
2. Remove the backing paper from one side of each
double-sided adhesive strips. Fix one adhesive strip
to the back of the Magnet and one to the back of
the Transmitter (alternatively for permanent fixing
use the screws supplied).
3. Peel off the other side of each adhesive strip.
Mount the Magnet on the door and the
Transmitter on the door frame (small triangles
facing each other), with less than a 6mm
separation between the two.
4. When opening the door a small red indicator
lights up briefly, this indicates that the
Transmitter has sent a signal
to the Control Panel.

GUARANTEE
REMOTE CONTROL BUTTONS/FUNCTIONS
Disposal and Recycling
Disposal of this product is covered by the Waste Electrical or Electronic Equipment (WEEE)
Directive. It should not be disposed of with other household or commercial waste.
At the end of its useful life the packaging and product should be disposed of via a suitable
recycling centre. Please contact your local authority or the retailer from where the
product was purchased for information on available facilities.
The product is guaranteed for one year from the date of purchase against faulty materials and
workmanship. No liability can be accepted for any problems caused by fair wear and tear, buyer’s
negligence, improper fitting or use, wilful or accidental damage, or any consequential loss or
damage howsoever caused. This guarantee does not affect your statutory rights and is valid for UK
and EIRE only.
If you believe the product to be faulty or in the unlikely event of the product developing a fault
during the warranty period, then please contact our Technical Support Team (contact details shown
below) for product assistance. Product repair or replacement will be offered for faulty products only
with our prior agreement. Should you need to return a product then:
1. Contact the Helpline on the number below to obtain a Return Authorisation Number
2. Return your product adequately packaged, ideally in its original packaging to prevent damage
in transit, and include the following:
a. A copy of your original invoice/receipt
b. A covering letter giving your full contact details, including email address (if applicable)
c. A description of the fault or problem
Arm Press to Arm the Control Panel/Siren and all of the Accessories (Full Arm)
Disarm Press to Disarm the System
Part Arm
(Home Arm) Press to Part Arm the System (for Control Unit Systems only)
Panic Press to activate a Panic Alarm (SOS). The Control Panel will auto-dial out to
the pre-set phone numbers immediately
Mute Arm Press to Arm the System with the Solar Siren in Mute/Silent Mode
Mute Disarm Press to Disarm the System with the Solar Siren in Mute/Silent Mode
SOS
+
+
www.responseelectronics.com
Response Electronics Limited, Roman House, Lysons Avenue, Ash Vale, Surrey, GU12 5QF
email: [email protected]

SUGGESTED LAYOUT:
PMR1_V3_1424
miGuard is a trademark of Response Electronics Limited © copyright 2014 All rights reserved