MikroTik RouterBOARD OmniTik 5HnD User manual

RouterBOARD OmniTik 5HnD
Quick Setup Guide and Warranty Information
The RouterBOARD OmniTik comes preinstalled in an outdoor case, with a built-in 5GHz
802.11a/n wireless and five 10/100 Ethernet ports which support MDI-X auto detection.
There are two built-in antennas. One antenna is v-pol, the other is h-pol. Antenna gain is
7.5dbi. The device is packaged with a 24V power adapter, a PoE injector, a mounting
bracket and a hose clamp.
First use
•Open the small door on the bottom of the case, connect an Ethernet cable to the
Ethernet port. If you want to connect more than one Ethernet cable, you have to
break out the hole-blockers.
•OmniTik accepts 8-30V Passive PoE from a PoE injector. The package includes a
24V power adapter and a PoE injector.
•The default IP address from LAN is 192.168.88.1 for configuration
•Username is admin and there is no password
Powering
The board accepts powering from the Ethernet port (Passive PoE):
•Ethernet port accepts passive Power over Ethernet 8-30V DC. Package contains a
24V adapter and a PoE injector.
Maximum power consumption of the device is 9W.
Power output
The OmniTik UPA-5HnD can supply PoE powering to external devices from its Ethernet
ports. This is convenient as you don't need any additional PoE injectors on a tower to pow-
er other wireless devices. This feature is indicated by the letter “P” in the device model
name. The output Voltage will be the same as input Voltage, and this feature will have to be enabled on the specific
ports in RouterOS software. By default it is disabled. Output is possible on ports 2-5. Once Power Output is enabled in
RouterOS, the Ethernet LED light turns from Green, to Red. Read LED means the port is currently providing PoE
power.
Booting process
This device doesn't come fitted with a Serial Port connector, so initial connection has to be done via the Ethernet ca-
ble, using the MikroTik Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.1
with the username admin and no password.
In case IP connection is not available, Winbox can also be used to connect to the MAC address of the device. Infor-
mation here: http://wiki.mikrotik.com/wiki/First_time_startup
In case you wish to boot the device from network, for example to use MikroTik Netinstall, hold the RESET button of
the device when starting it until the LED light turns off, and the device will start to look for Netinstall servers.
Mounting
OmniTik comes bundled with one mounting bracket and one hose clamp for putting the device on a pole. You should
avoid connecting a loose Ethernet cable to the Ethernet port, secure the cable to a wall or the pole, so that the cable
weight is not pulling the port. It is recommended to secure the Ethernet cable less than 2m from the device. This is to
ensure that the cable doesn't damage the port by its weight, or doesn't fall out.
www.routerboard.com !21 Nov 20161

Expansion Slots and Ports
•One built in 5GHz 802.11a/n wireless, 2x2 MIMO. Two built-in antennas (h-pol and v-pol)
•Five individual 10/100 Ethernet ports, supporting automatic cross/straight cable correction (Auto MDI/X), so
you can use either straight or cross-over cables for connecting to other network devices. The First Ethernet
port accepts 8-30V DC powering from a passive PoE injector.
•One USB2.0 port
Buttons and Jumpers
• RouterOS reset jumper hole (no direct access, board has removed from case) – resets RouterOS software to de-
faults. Must short circuit the metallic sides of the hole (with a screwdriver, for example) and boot the device. Hold
screwdriver in place until RouterOS configuration is cleared.
• RouterBOOT reset button (access through the plastic door) has two functions:
• Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configu-
ration (same result as with reset hole)
• Hold this button during boot time longer, until LED turns off, and then release it to make the device look for
Netinstall servers.
Operating System Support
Currently tested operating system is MikroTik RouterOS (starting from version v6).
Copyright and Trademarks.
Copyright MikroTikls SIA. This document contains information protected by copyright law. No part of it may be repro-
duced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD, RouterOS,
RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in
this document are the property of their respective holders.
Hardware. MikroTik warrants all RouterBOARD series equipment for the term of twelve (12) months from the shipping
date to be free of defects in materials and workmanship under normal use and service, except in case of damage
caused by mechanical, electrical or other accidental or intended damages caused by improper use or due to wind,
rain, fire or other acts of nature.
To return failed units to MikroTik, you must perform the following RMA (Return Merchandise Authorization) procedure.
Follow the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process.
1. If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding
all warranty and repair issues, the following instructions apply ONLY if you purchased your equipment directly
from MikroTik in Latvia.
2. We do not offer repairs for products that are not covered by warranty. Exceptions can be made for RB1000
series.
3. Out-of-warranty devices and devices not covered by warranty sent to Mikrotikls will be returned to the sender
at sender's cost.
RMA Instructions are located on our webpage here: http://rma.mikrotik.com
This document is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to,
the implied warranty of merchantability and fitness for a particular purpose. The manufacturer has made every effort to
ensure the accuracy of the contents of this document, however, it is possible that it may contain technical inaccura-
cies, typographical or other errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or
indirect, incidental, consequential or other damages that may result from such an inaccuracy, including, but not limited
to, loss of data or profits. Please report any inaccuracies found to [email protected]
www.routerboard.com !21 Nov 20162

Federal Communication Commission Interference Statement !
(FCC ID: TV7OMNITIK5HND)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-
tial installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or tele-
vision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation. This device and its an-
tenna must not be co-located or operation in conjunction with any other antenna or transmitter.
IMPORTANT: Exposure to Radio Frequency Radiation.
5cm minimum distance has to be maintained between the antenna and the occupational user and 10
cm to general public. Under such configuration, the FCC radiation exposure limits set forth for an popu-
lation/uncontrolled environment can be satisfied.
www.routerboard.com !21 Nov 20163

CE Declaration of Conformity
Full Declaration of Conformity (DoC) may be obtained by visiting this web page: http://routerboard.com/doc/
EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More informa-
tion on http://wiki.mikrotik.com BG. Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете 192.168.88.1 в
уеб браузър, за да настроите продукта. Повече информация вhttp://wiki.mikrotik.com CZ. Návod k použití: Připojte napájecí adaptér k zapnutí
přístroje. Otevřete 192.168.88.1 ve webovém prohlížeči pro konfiguraci produktu. Více informací najdete v http://wiki.mikrotik.com DK. Instruk-
tionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.88.1 i en webbrowser til at konfigurere produktet. Mere information i http://
wiki.mikrotik.com FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web
pour configurer le produit. Plus d'informations dans http://wiki.mikrotik.com DE. Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät
einzuschalten. Öffnen Sie 192.168.88.1 in einem Web-Browser, um das Produkt zu konfigurieren. Weitere Informationen im http://wiki.mikrotik.com
EE. Kasutusjuhend: Ühendage toiteadapter seadme sisselülitamiseks. Avatud 192.168.88.1 in veebilehitseja seadistada toodet. Rohkem teavet
http://wiki.mikrotik.com ES. Manual de instrucciones: Conecte el adaptador de alimentación para encender la unidad. Abra 192.168.88.1 en un
navegador web para configurar el producto. Más información en http://wiki.mikrotik.com IT. Manuale di istruzioni: Collegare l'adattatore di alimen-
tazione per accendere l'unità. Aprire 192.168.88.1 in un browser Web per configurare il prodotto. Maggiori informazioni in http://wiki.mikrotik.com
LV. Lietošanas instrukcija: Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.88.1 ar interneta pārlūku, lai konfigurētu produktu.
Plašāka informācija http://wiki.mikrotik.com LT. Naudojimosi instrukcija: Prijunkite maitinimo adapterįįjunkite įrenginį. Įinterneto naršyklę
192.168.88.1 Atidarykite galite konfigūruoti gaminį. Daugiau informacijos rasite http://wiki.mikrotik.com HU. Használati utasítás: Csatlakoztassa a
hálózati adaptert a készülék bekapcsolásához. Megnyitása 192.168.88.1 egy webböngészőben beállítani a terméket. Több információ http://wik-
i.mikrotik.com NL. Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.88.1 in een webbrowser om het product
te configureren. Meer informatie in http://wiki.mikrotik.com PL. Instrukcja obsługi: Podłącz adapter zasilania, aby włączyćurządzenie. Otwórz
192.168.88.1 w przeglądarce internetowej, aby skonfigurowaćurządzenie. Więcej informacji w http://wiki.mikrotik.com PT. Manual de instruções:
Conecte o adaptador de alimentação para ligar o aparelho. Abra 192.168.88.1 em um navegador da web para configurar o produto. Mais infor-
mações em http://wiki.mikrotik.com RO. Instrucțiuni de utilizare : Conectați adaptorul de alimentare pentru a porni aparatul. Deschide
192.168.88.1 într-un browser web pentru a configura produsul. Mai multe informații în http://wiki.mikrotik.com SK. Návod na použitie: Pripojte
napájací adaptér k zapnutiu prístroja. Otvorte 192.168.88.1 vo webovom prehliadači pre konfiguráciu produktu. Viac informácií nájdete v http://wik-
i.mikrotik.com SI. Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. Večinformacij v
http://wiki.mikrotik.com FI. Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen. Lisää tietoa http://wik-
i.mikrotik.com SE. Instruktionsmanual: Anslut nätadaptern för att slå på enheten. Öppna 192.168.88.1 i en webbläsare för att konfigurera produk-
ten. Mer information på http://wiki.mikrotik.com NO. Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne 192.168.88.1 i en net-
tleser for å konfigurere produktet. Mer informasjon på http://wiki.mikrotik.com GR. εγχειρίδιο οδηγιών: Συνδέστε τον προσαρµογέα τροφοδοσίας
για να ενεργοποιήσετε τη µονάδα. Ανοίξτε 192.168.88.1 σε ένα πρόγραµµαπεριήγησης στο Web για να διαµορφώσετε το προϊόν. Περισσότερες
πληροφορίες στο http://wiki.mikrotik.com
[EN] English
Hereby, MIKROTĪKLS SIA declares that this ROUTERBOARD is in compliance with the essential requirements and other relevant provisions
of Directive 1999/5/EC.
[BG] Bulgarian
Снастоящето, MIKROTĪKLS SIA декларира, че ROUTERBOARD евсъответствие със съществените изисквания идругитеприложими
разпоредби на Директива 1999/5/EC.
[CZ] Czech
MIKROTĪKLS SIA tímto prohlašuje, že ROUTERBOARD splňuje základní požadavky a všechna příslušná ustanoveni Směrnice 1999/5/ES.
[DK] Danish
Undertegnede MIKROTĪKLS SIA erklærer herved, at følgende udstyr ROUTERBOARD overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
[DE] German
Hiermit erklärt MIKROTĪKLS SIA dass sich das Gerät ROUTERBOARD in Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
[EE] Estonian
Käesolevaga kinnitab MIKROTĪKLS SIA seadme ROUTERBOARD vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tu-
lenevatele teistele asjakohastele sätetele.
[GR] Greek
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ ΟΚΑΤΑΣΚΕΥΑΣΤΗΣ MIKROTĪKLS SIA ΔΗΛΩΝΕΙ ΟΤΙ ROUTERBOARD ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ
[ES] Spanish
Por la presente, MIKROTĪKLS SIA declara que este ROUTERBOARD cumple con los requisitos esenciales y otras exigencias relevantes de la
Directiva 1999/5/EC.
[IT] Italian
Con la presente MIKROTĪKLS SIA dichiara che questo ROUTERBOARD è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
[LV] Latvian
Ar šo MIKROTĪKLS SIA deklarē, ka ROUTERBOARD atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteiku-
miem.
[LT] Lithuanian
Šiuo MIKROTĪKLS SIA deklaruoja, kad šis ROUTERBOARD atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas
[HU] Hungarian
A MIKROTĪKLS SIA ezzennel kijelenti, hogy a ROUTERBOARD típusú beren-dezés teljesíti az alapvetőkövetelményeket és más 1999/5/EK
irányelvben meghatározott vonatkozó rendelkezéseket.
[NL] Dutch
Hierbij verklaart MIKROTĪKLS SIA dat het toestel l ROUTERBOARD in overeenstemming is met de essentiële eisen en de andere relevante
bepalin-gen van richtlijn 1999/5/EG.
[PL] Polish
Niniejszym MIKROTĪKLS SIA deklaruje że ROUTERBOARD jest zgodny z zasadniczymi wymaganiami i innymi właściwymi postanowieniami
Dyrektywy 1999/5/EC.
[PT] Portuguese
Eu, MIKROTĪKLS SIA declaro que o ROUTERBOARD cumpre os requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.
[RO] Romanian
Prin prezenta, MIKROTĪKLS SIA declarăcăaparatul ROUTERBOARD este în conformitate cu cerinţele esenţiale şi cu alte prevederi perti-
nente ale Directivei 1999/5/CE..
[SK] Slovak
MIKROTĪKLS SIA týmto vyhlasuje, že ROUTERBOARD spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.
[SI] Slovenian
MIKROTĪKLS SIA izjavlja, da je ta ROUTERBOARD v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive 1999/5/ES.
[FI] Finish
MIKROTĪKLS SIA vakuuttaa täten että ROUTERBOARD tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
[SE] Swedish
Härmed intygar MIKROTĪKLS SIA att denna RouterBOARD är i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG.
[NO] Norwegian
MIKROTĪKLS SIA Erklærer herved at ROUTERBOARD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.
www.routerboard.com !21 Nov 20164