Milly and Coup Leo User manual

IMPORTANT! READ CAREFULLY
AND KEEP FOR FUTURE REFERENCE
Bassinet & Seat Set
Product Manual
Leo

2
Contents
Leo Product Manual
3.
5.
6.
7.
8.
9.
10.
11.
12.
14.
15.
1 7.
1 9.
20.
22.
23.
23.
Safety warnings
Parts checklist
Setting up your frame
Folding the stroller
Double or single mode?
Configurations
Setting up your bassinet
Using your bassinet
Setting up your seat
Using the harness
Using your Leo
Free accessories
Using Leo with a car capsule
Leo maintenance
Cleaning instructions
Spare parts
Warranty

3
Leo Product Manual
Tips to avoid tears
• Never use the stroller in a manner
for which it is not designed.
• Do not allow your child to climb,
stand on or play with the stroller.
• Do not use parts or accessories that
are not approved for use with the
Leo range. Doing so may be unsafe
and may also void your warranty.
• Ensure you carefully explain usage
and safety features to new carers
before they use the stroller.
• Remove your child and fold the
stroller when going up or down
stairs or escalators.
• Take your child out of the stroller
when travelling by bus, tram,
or train.
• Gentle sloping surfaces may
be unstable. On steeper sloping
and uneven surfaces, there is
a possibility that the stroller may
tip over and you may need to
remove your child.
• Do not use or leave the pram near
open fire or an exposed flame.
• Only to be used for walking. Not
suitable for running, rollerblading
or skating etc.
Leo is designed and tested to comply with Consumer Protection Notice No. 8
of 2007, AS 2088:2022 and AS/NZS ISO 8124-3.
• FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
• PUT ON ALL THE BRAKES WHENEVER YOU PARK THE STROLLER.
• DO NOT LEAVE CHILDREN UNATTENDED.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU
ADJUST THE STROLLER, OTHERWISE THEY MAY BE INJURED.
Weight limits
• Maximum weight for a child in the seat is 20kg.
• Maximum weight for items in the basket is 8kg.
• Maximum weight that can be hung from the handlebar is 2kg.
• Maximum weight for the toddler board (sold separately) is 20kg.
General safety

4
Tips to avoid tears
Leo Product Manual
• The Milly + Coup Toddler Board (sold as a separate accessory)
is compatible with Leo.
• Leo is only compatible with select car capsule models using the
approved capsule adaptors. Refer to our website for full compatibility.
Accessories
WHEN USING THE STROLLER WITH
ONE CHILD, THE DOUBLE ADAPTORS
MUST NOT BE USED
WHEN USING THE FRONT SEAT IN
PARENT FACING MODE THE SEAT
CANNOT BE RECLINED

5
Leo Product Manual
Meet Leo
Parts Checklist
Please check that you have all the correct
parts before getting started.
Stroller frame
1 x Stroller seat
1 x Bassinet
Double adaptors
1 x Belly bar
Harness cover set
1
2
3
4
5
6
1 x Seat UV cover (located
in seat footrest pocket)
2 x Front wheels
2 x Rear wheels
1 x Seat liner
Handlebar bag
1 x Bassinet UV cover (located
in bassinet footend pocket)
7
8
9
10
11
12
4
1
3
5
6
7
89
2
10 12
11

66
Leo Product Manual
To open the frame, release the
frame lock.
Lift the handlebar upwards until you
hear the frame ‘click’ into place.
Insert each rear wheel pin into the
sides of the brake bar until you hear
a ‘click’. Give them a tug to ensure
they are attached securely.
Insert the front wheels into the centre
of the socket ensuring you hear them
‘click’ in.
Thread the basket tab through the
slot behind the rear wheel hub and
secure the press stud. Repeat for
the other side.
Setting up your frame

77
Leo Product Manual
Folding the stroller
Before folding, ensure that the brake is engaged, the front wheels
are unlocked, and the handlebar is at the lowest height position.
Remove the second seat, bassinet, or capsule by lifting the release
levers on either side (the stroller can be folded with one seat in the
forward facing position only.)
Standing at the front of the stroller, slide the black buttons located
on the black circular handles and the frame will fold in half.
Ensure the automatic frame lock has engaged on the side of the
stroller before lifting the frame up using the circular handles.
• ENSURE CHILDREN ARE OUT OF REACH OF THE STROLLER BEFORE
FOLDING.
• TAKE EXTRA CARE WHEN FOLDING, LIFTING AND CARRYING THE STROLLER.
ALWAYS LIFT AND CARRY YOUR STROLLER USING BOTH HANDS.
• TO AVOID POSSIBLE INJURY, ALWAYS ENSURE THAT THE FRAME LOCK IS
SECURED BEFORE LIFTING AND CARRYING THE STROLLER.
• TO AVOID FINGER ENTRAPMENT, KEEP YOUR OWN AND YOUR CHILDREN’S
FINGERS CLEAR OF ANY FOLDING PARTS.
• ALWAYS REMOVE THE BASSINET, SECOND SEAT OR CAR CAPSULE PRIOR
TO FOLDING AND CARRY THE FRAME AND BASSINET/SEAT/CAR CAPSULE
SEPARATELY. ONLY LIFT AND CARRY AFTER FOLDING.

8
Leo Product Manual
8
THERE IS AN INCREASED RISK OF THE STROLLER TIPPING IF USED
IN DOUBLE MODE WITH ONLY ONE CHILD IN THE SEAT. PLEASE BE
MINDFUL OF THIS AND HOLD THE STROLLER AT ALL TIMES IF YOU
ARE DOING SO.
Single Mode
When using the stroller in single mode, the
double adaptors must not be used. The
bassinet or seat can be attached directly
into the central connectors on the frame.
Double Mode
Attach the two sets of double adaptors.
The upper adaptors attach into the central
connectors for the “top position”. To remove
them simply push the buttons on the side
and lift o.
The lower adaptors will slide onto the guides
at the front of the frame for the “lower
position”. To remove them you will need to
release the tab at the top of the connector
before sliding o.
Upper adaptors
Lower adaptors
Double or single mode?

9
Leo Product Manual
9
Configurations
You can purchase an additional seat, bassinet, or capsule adaptors on our
website to enable the following configurations.
Single mode:
Seat + bassinet:
Two seats:
Two bassinets:
Car Capsules:

10
Leo Product Manual
Using the fabric handles, pull the frame
support rods towards the ends of the
bassinet until they lock under the plastic
clips. These rods will feel very tight, this is
to ensure they will not become loose and
collapse the bassinet during use.
Zip up the fabric and insert the bassinet
mattress.
Zip the bassinet cover on. Secure the press
studs.
To release the canopy, press the round
buttons on the sides of the canopy frame.
Note: Do not put downward pressure
on the canopy until the buttons are
completely depressed or it will feel stuck
and not move.
Setting up your bassinet

11
Leo Product Manual
Using your bassinet
• DO NOT USE THIS BASSINET ONCE THE CHILD CAN SIT UP UNAIDED.
• DO NOT USE FOR UNSUPERVISED SLEEPING.
• DO NOT ADD AN ADDITIONAL MATTRESS OR PADDING INSIDE
THE BASSINET.
Attaching & releasing the bassinet from the frame
Attach the bassinet onto either the central
connectors of the frame for single mode or the
double adaptors for double mode. To release,
press the buttons and lift the bassinet up o the
frame. The bassinet can face either direction.
Note: To reduce the risk of SIDS, paediatricians
recommend healthy infants be placed on their
backs to sleep, unless otherwise advised by
your physician.
For additional air flow, simply open
the ventilation panel on the back
of the canopy.
The bassinet comes with a seperate UV
cover. It is located in the pocket inside
the foot end of the bassinet.
To attach: thread the toggles to the loop fixing points on the inside
of the canopy. Pull the elastic end over the foot end of the bassinet
and secure the tabs on each side of the UV cover underneath the
frame tube of the bassinet.

12
Leo Product Manual
Setting up your seat
Line up the seat connectors with the frame
and press downwards. Listen for the ‘click’
to ensure it is securely locked in place.
Attach the plastic canopy connectors onto
the sides of the seat frame (TIP: attach
from top to bottom). You’ll notice a round
guide on each side, the connectors should
attach over these guides.
Note: For additional headroom you can
attach the canopy connectors higher up
on the frame above the guides.
Insert the belly bar into the belly bar
sockets on the seat frame. Always give the
bar a firm tug to ensure its secure.
Note: To remove from one side or both,
press the button on the side you want to
release, and pull the belly bar out.

13
Leo Product Manual
Setting up your seat
• THIS STROLLER SEATS TWO PASSENGERS WITH A MAXIMUM
WEIGHT LIMIT OF 20KG EACH.
• THE STROLLER SEATS ARE NOT RECOMMENDED FOR CHILDREN
UNDER 6 MONTHS.
• DO NOT ALLOW YOUR CHILD TO CLIMB UNASSISTED INTO THE
STROLLER.
• DO NOT USE THIS SEAT WITH ANY OTHER MODELS OF STROLLER.
To recline the seat: press the large,
round buttons on the sides of the seat
connectors and tilt the seat forward or
back.
To remove the seat: press the oval buttons
on the sides of the seat connectors and
lift up.
Note: the seat can be faced in the forward
or rear facing position.

14
Leo Product Manual
Using the harness
To secure and release the harness
Insert each of the four harness straps into
the central buckle.
To release, press the button in the middle
of the buckle.
To adjust the length of the shoulder straps
Slide the buckle along the strap to the
desired position.
To adjust the height of the shoulder straps
Slide the buckle that is secured to the seat
back up or down the strap to the desired
position for your child.
To adjust the length of the waist straps
Pull the adjustor buckle along the waist
strap to the desired length.
• USE THE HARNESS AT ALL TIMES.
• ENSURE THAT YOUR CHILD CORRECTLY WEARS THE FITTED AND
ADJUSTED SAFETY HARNESS AT ALL TIMES WITH ALL 5 STRAPS SECURED.
• NEVER LEAVE THE HARNESS BUCKLED WHEN NOT FITTED TO A CHILD
IN THE STROLLER BECAUSE THE HARNESS CAN FORM LOOPS WHICH
MAY POSE A STRANGULATION HAZARD.

Leo Product Manual
15
Using your Leo
When stopped, use the brake at all times
by pressing down on the bottom of the red
brake paddle with your foot until you feel it
click into place.
To start travelling again press down on the
top of the red brake paddle with your foot to
disengage the brake and o you go!
Rear brake
OFF
ON
Adjusting the footrest
Note: Do not put downward pressure
on the footrest until the buttons are
completely depressed or it will feel stuck
and not move.
Lift the foot rest and it will click into the
highest position. To release, press both
footrest buttons simultaneously and lower.
NEVER LET CHILDREN SIT ON THE FOOTREST OR CLIMB INTO THE SEAT
USING THE FOOTREST. DOING SO MAY SNAP OR DAMAGE THE FOOTREST
AND IS NOT COVERED BY YOUR WARRANTY.
Adjusting the handlebar
Push the button in the middle of the
handlebar and pull or push to your desired
height. It may require a slight ‘jiggle” to
adjust.

16
Using your Leo
Leo Product Manual
• USE THE TETHER STRAP TO STOP THE STROLLER ROLLING AWAY.
• DO NOT HANG ANY OTHER BAGS OTHER THAN THE LEO HANDLEBAR
BAG FROM THE HANDLEBAR. DOING SO MAY UNBALANCE AND TIP
YOUR STROLLER.
• THE LEO HANDLEBAR BAG HAS BEEN TESTED TO HOLD 2KG.
• BE CAREFUL CARRYING LIQUIDS IN THE HANDLEBAR BAG. HOT LIQUIDS
MAY BURN YOU OR YOUR CHILD.
To remove the wheels, you will need to
use a flat screw driver or similar tool to
carefully press in the silver button located
on the wheel hub. Please take care whilst
doing this.
When travelling quickly along straight surfaces or across uneven terrain, the
front wheels may spin or cause what’s commonly known as “wheel shudder”.
Front swivel wheels
To lock the front wheels into place, press down
on the wheel lock buttons (located on the
back of the wheel sockets). To go back to 360
swivel mode, press the buttons up again.
Rear wheels
To remove the rear wheels, press the
button located on the brake bar and pull
the wheel o.

17
Leo Product Manual
Free accessories
Rain covers
The rain covers are compatible
with both the seat and bassinet.
Place them over the top of the
seat or bassinet. The open flap
should be at the top, this is to
access the bassinet handle.
UV/Sleep/Mosquito Cover
There are two UV covers included with your Leo
– one for the seat and one for the bassinet.
The seat UV cover is located in the zipper
pocket underneath the seat foot rest.
For the seat: Place it over the seat canopy and attach the elastic to
the back of the canopy connectors and then tuck under the footrest.
The bassinet UV cover is located in a pocket
inside the foot end of the bassinet.
• NEVER LEAVE THE STROLLER COVERED INDOORS, IN VERY HOT
WEATHER OR NEAR A HEAT SOURCE.
• ALWAYS SUPERVISE AND MONITOR YOUR CHILD REGULARLY WHILE
THE STROLLER IS COVERED.

18
Free accessories
Leo Product Manual
Handlebar Bag
Adjust the strap of the handlebar bag
to the desired length and slip over the
handlebar.
Position the bag behind the hooks on
either side of the handlebar to keep it in
place.
For the bassinet: Attach the toggles to
the loop fixing points on the inside of
the bassinet canopy. Pull the elastic end
over the foot end of the bassinet and
secure the tabs on each side of the UV
cover underneath the frame tube of the
bassinet.
UV/Sleep/Mosquito Cover cont.
Seat Liner
Attach the seat liner by threading the
harness straps from the seat through the
corresponding slot.
Secure the seat liner to the seat by
threading the plastic toggles through
the slots in the top of the seat and
secure through the elastic loops.

19
Leo Product Manual
Using Leo with a car capsule
To attach your capsule:
1. Apply the brake before attaching the adaptors
to the corresponding connector points on both
sides of the stroller frame.
2. Lift your capsule and carefully lower it onto the
adaptors until you hear a click. This indicates
your capsule is now secured to your stroller.
The following car capsules are compatible with the Leo Capsule Adaptors.
Please refer to our website for the most current compatibility list.
• Maxi Cosi Citi
• Maxi Cosi Titan
• Maxi Cosi Mico Plus
• Maxi Cosi Mico (manufactured
from 2014 onwards)
• Maxi Cosi Mico AP (manufactured
from 2013 onwards)
• Joie Gemm
• Joie i-Gemm
• Cybex Cloud Q
• Nuna KLIK Plus
• FOLLOW THE CAR CAPSULE MANUFACTURER’S INSTRUCTIONS
CAREFULLY TO PREVENT INJURY OR EVEN DEATH.
• READ CAPSULE MANUFACTURER’S MAXIMUM USAGE TIME
RECOMMENDED FOR BABY TO REMAIN IN YOUR SPECIFIC CAPSULE.
• DO NOT USE ANY CAPSULE NOT AUTHORISED BY MILLY + COUP.
• ENSURE ALL FINGERS AND BODY PARTS ARE CLEAR OF THE CAPSULE
AND STROLLER FRAME WHEN ATTACHING.
• NEVER PLACE THE CAR CAPSULE IN THE CAR WHILE ADAPTORS
ARE ATTACHED.

20
Leo Product Manual
Using Leo with a car capsule
Leo maintenance
Excessive wear can reduce the eectiveness and safety of your stroller.
Please be gentle, don’t overload it, avoid excessive o-road use and be
sure to follow the maintenance instructions below to keep your stroller
looking and feeling newer for longer!
Regular maintenance:
• Inspect the locking devices, levers, joints, buttons, brakes, wheels, safety
harness and fixtures to ensure they are secure, moving freely and in fully
working order.
• If your front wheels or any parts of the stroller have become sti, dicult to
operate or begin to squeak, first ensure that dirt is not the cause and give
them a good clean with a damp (not wet) cloth. Then try a light application
of a sprayable silicone lubricant, ensuring that it penetrates between the
components.
To remove your capsule:
1. Apply the brake then simultaneously press the
release buttons on each side of the capsule
and lift the capsule o the adaptors.
Note: Each capsule mentioned above will
have slightly dierent buttons to release the
car capsule from the adaptors.
2. To remove the adaptors from the stroller
frame, push the release buttons on either side.