MILUX MIAF-4020 User manual

20” COMMERCIAL AUTO FAN
MODEL: MIAF-4020
INSTRUCTION MANUAL
Please read this manual carefully before operating this product.
Keep this manual handy for further reference.
Distributed by:
MILUX SALES & SERVICE SDN. BHD. (302263-X)
No. 31, Lorong Jala 14/KS10, Off Jalan Telok Gong,
42000 Port Klang, Selangor, Malaysia.
Tel: [phone] Fax: [phone] Toll Free: 1800-88-MILUX (64589)
E-mail: [email protected]
Website: www.milux.com.my
21 cm
14.85 cm

Parts Identification
Specifications
1
21 cm
14.85 cm
1. Front Guard Ornament
2. Front Guard
3. Guard Ring
4. Fan Blade
5. Rear Guard
6. Motor Body
7. Bracket
1
Model MIAF-4020
Voltage 220~240V-50Hz
Power 150W
Fan Blade Size 20”
Speed
(RPM)
Maximum Speed 1400
Minimum Speed 1010
Air Delivery 8500m³/h
Effective Coverage Area 20m³ to 30m³
*Note: Specifications are subject to change without prior notice.
2
3
4
5
6
7

21 cm
14.85 cm
2
Cautions
Maintenance and Cleaning
• This appliances is not intended for use by persons (including children) with reduce physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
• Do not use this appliance in high temperature and high humidity area.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard .
• Must use separate, well-earthed and 3 core cable & plug top.
• Keep children away from package and its parts. Danger of suffocation from cartons and plastic film.
• Always ensure that electrical mains is turned off and unplug before cleaning the appliance.
• When pulling out the plug, do not pull cord to avoid cord damage.
• Do not insert finger or other objects into the fan guard.
• Do not use the appliance outdoor or near windows. Rain drop may cause electrical hazards.
• Do not operate this appliance without a fan blade, broken or bent fan blade.
• Handle fan blade with care during cleaning.
• Do not bend the blades when installing and maintaining.
• Use mild soap with damp cloth or sponge to clean the fan. Wipe until dry .
• The ventilation holes of rear motor cover must be free of dust and dirt. Please clean is frequently.
Assembly Step
(a) Rear Guard
• Remove 4 screws at front of Motor Assembly.
• Put the Rear Guard on the Motor assemble.
• Screw and tighten the 4 screw.
(b) Fan Blade Assembly
• Remove Protective Film on the Fan Blade.
• Tighten up all screw at the lateral of canter piece.
• Take The Fan Blade and press on the Canter Piece.
• Use the Hex driver to fix screw at fan blade and centre piece.
Note: Take note on the fan blade direction.
M5X6(4)

21 cm
14.85 cm
Assembly Step
Installation
(c) Fan Blade Installation
• Locate flat surface at motor shaft.
• Insert Fan Blade to motor shaft with screw face to
flat surface.
• Tighten the fan blade screw.
Note: Please take note on the fan blade direction.
(d) Front Guard Assembly
• Insert screw into Guard Ring hole & turn clockwise by 2 cycle
• Assembly the Guard Ring and Front Guard
• Fit and match The Front Guard & Rear Guard together .
• Tighten up The Guard Ring screw .
(a) Wiring Diagram
34
(b) Regulator Wiring
(c) Assembly the unit
(i) Remove 4 screws as shown in figure A.
(ii)
• Remove 2 screws at side of the bracket (Figure B).
• Remove main bracket from fan (Figure C).
• Install bracket on the ceiling by using 2 wall plug.
• Put back main body into bracket and screw back side screw.
Note: Regulator is using Veriable Resistor system
(Speed 6 is the highest speed and speed 1 is the lowest speed)
Warning:
This product is not provided with cord and plug. When connect the appliances with power supply, it must installed by
qualified personnel in order to aviod hazard.
Neck Joint
Guard Ring
Guard Ring Cover
Figure A
Tongue
Groove
Black Wire
Wire
220V~/50Hz
Synchronise
Motor
Thermal Fuse
Brown Wire
MS1
~
Motor
CN
L
Yellow / Green
Installation
L (Live Wire) L1 (Live Wire)
Input
Speed Control Switch
Model: MIAF-4020
Output
Note: Do not connect Natural
cable into the switch
Load Power:≤400W (Do Not Overload)
Batch No:2020150A
Natural Wire
(N)
2A 220V~
L(Live Wire)
Input L1(Live Wire) Output
Live Wire
(L)
C
B
Fixing Plate
Orbit Fan Installation Sheet
Expansion Bolts