MILUX MISF-1120 User manual

20” COMMERCIAL STAND FAN
MODEL: MISF-1120
INSTRUCTION MANUAL
Please read this manual carefully before operating this product.
Keep this manual handy for further reference.
Distributed by:
MILUX SALES & SERVICE SDN. BHD. (302263-X)
No. 31, Lorong Jala 14/KS10, Off Jalan Telok Gong,
42000 Port Klang, Selangor, Malaysia.
Tel: [phone] Fax: [phone] Toll Free: 1800-88-MILUX (64589)
E-mail: [email protected]
Website: www.milux.com.my
21 cm
14.85 cm

Parts Identification
Specifications
1
21 cm
14.85 cm
1. Front Guard Ornament
2. Front Guard
3. Guard Ring
4. Fan Blade
5. Rear Guard
6. Motor Body
7. Power Cord
8. Inner Pole
9. Outer Pole Lock Nut
10. Outer Pole
11. Stand Pole Bowl
12. Base Screw
13. Base
12 3 4 5 6
8
7
9
10
12
11
13
Model MISF-1120
Voltage 220~240V-50Hz
Power 150W
Fan Blade Size 20”
Speed
(RPM)
Maximum Speed 1400
Minimum Speed 1010
Air Delivery 8500m³/h
Effective Coverage Area 20m³ to 30m³
*Note: Specifications are subject to change without prior notice.

21 cm
14.85 cm
2
Cautions
Maintenance and Cleaning
• This appliances is not intended for use by persons (including children) with reduce physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
• Do not use this appliance in high temperature and high humidity area.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard .
• Must use separate, well-earthed and 3 core cable & plug top.
• Keep children away from package and its parts. Danger of suffocation from cartons and plastic film.
• Always ensure that electrical mains is turned off and unplug before cleaning the appliance.
• When pulling out the plug, do not pull cord to avoid cord damage.
• Do not insert finger or other objects into the fan guard.
• Do not use the appliance outdoor or near windows. Rain drop may cause electrical hazards.
• Do not operate this appliance without a fan blade, broken or bent fan blade.
• Handle fan blade with care during cleaning.
• Do not bend the blades when installing and maintaining.
• Use mild soap with damp cloth or sponge to clean the fan. Wipe until dry .
• The ventilation holes of rear motor cover must be free of dust and dirt. Please clean is frequently.
Assembly Step
(a) Base assembly
• Place Base on the floor.
• Fit the outer pole to the centre of the base.
• Insert Hex bolt through pole & base.
• Tilt Hex Bolt by insert Lock washer, washer and nut.
(b) Decoration Cover Assembly
• Remove Rotate Lock from outer pole.
• Insert Decoration Cover into outer pole.
• Put back Rotate Lock into original place.
Note: You may adjust Inner pole according to your selected height.
Hex Bolt (M6x12mm)
Split Lockwasher
Washer
Nut (M6)
Base
Rotate Lock
Decoration Cover
Inner Column
Column
Decoration Cover

21 cm
14.85 cm
Assembly Step
(c) Motor Assembly
• Locate tongue at the Neck Joint.
• Insert Tongue with groove at Inner Pole.
• Tighten 2 screw at the back of the Neck Joint.
(d) Rear Guard
• Remove 4 screws at front of Motor Assembly.
• Put the Rear Guard on the Motor assemble.
• Screw and tighten the 4 screw.
(e) Fan Blade Assembly
• Locate flat surface at motor shaft.
• Insert Fan Blade to motor shaft with screw face to flat surface.
• Tighten the fan blade screw.
Note: Please take note on the fan blade direction.
34
(f) Front Guard Assembly
• Insert screw into Guard Ring hole & turn clockwise by 2 cycle.
• Assembly the Guard Ring and Front Guard.
• Fit and match The Front Guard & Rear Guard together.
• Tighten up The Guard Ring screw.
Assembly Step
Operation
(a) Speed Control
• "0" position is power off
• Speed can be selected from "1 " which is minimum speed and up to speed "4" which is maximum
speed.
(b) Oscillation
• The oscillation function is controlled by synchronous motor . Turn the oscillation switch which at the
top of the motor to turn on.
(c) Vertical Angle
• Switch Off fan before adjust the vertical angle of the fan.
• Patent Design Neck Joint allowed to adjust angle by hand easily.
Neck Joint
Guard Ring
Guard Ring Cover
Tongue
Groove