Miniatures Archie 14495 User manual

Bookcase
1. Place Back (B) flat on the work surface.
2. Glue a Wall (W) to a long edge
of Back (B). All notches fit flush.
3. Glue a Shelf (S) to a short
edge of Back (B). Also, glue it
to the Wall (W).
4. Glue another Shelf (S) to the
other short edge of Back (B).
Also, glue it to the Wall (W).
5. Glue another Wall (W) to the other long edge of Back (B).
Also, glue it to both Shelves (S).
6. Use a damp clean cloth to wipe away any excess glue.
7. Let the glue set for a few minutes.
8. Glue the remaining four Shelves
(S) in place.
9. Use a damp clean cloth to wipe
away any excess glue.
10. Set this shelving assembly
aside.
2388 Pleasantdale Road, Atlanta, GA 30340 • 800-926-6464 • www.miniatures.com • Made in USA
BOOKCASE PARTS:
Back (B)
Wall (W) x2
Shelf (S) x6
Front (F)
Door (D) x2
FIREPLACE PARTS:
Firebox Back (FBB)
Firebox Wall (FBW) x2
Firebox Ceiling (FBC)
Mantel Shelf (MS)
Mantel Wall (MW) x2
Surround (SR)
11. Place Front (F) flat on the work
surface with the etched lines
facing up.
12. Add glue* to the edges of both
Doors (D).
13. Place both Doors (D) into the
square opening of Front (F)
with the etched lines facing up.
14. Lightly press both Doors (D) flat with Front (F).
15. Use a damp clean cloth to wipe away any excess glue.
16. Let the glue set for a moment.
17. Carefully turn this front assembly over and use a damp
clean cloth to wipe away any
excess glue on the back**.
18. Orient the front assembly with
its arch at the top and orient
the shelf assembly with its tall-
est shelf at the top.
19. Glue the front assembly onto
the shelving assembly. All edges
are flush.
20. Assembly of one bookshelf is now complete.
21. Repeat these instructions for the second bookshelf.
#14495 Archie Built-Ins and Mantel
Available exclusively at miniatures.com
Step-by-step assembly instructions
Copyright miniatures.com 2022
Assembly Instructions
1122
GENERAL INSTRUCTIONS
• Read all the instructions before you begin.
• Choose a work surface that is clean, dry
and protected from glue spills.
• Make sure all parts are in the kit.
• Do a dry fit, using masking tape to hold
parts in place, to make sure everything
fits together correctly before permanent
assembly.
Tip: Plan your finishes at the dry-fit stage, before final/permanent
assembly. It is easier to finish the panels as flat surfaces.
Disassemble and finish as desired, then reassemble using glue.
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2
3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W

7. Glue the Surround (SR) in place. It sits on
the front facing edges of the firebox. Ad-
just the Firebox Walls (FBW) and Firebox
Ceiling (FBC) so that they are flush with
the inside edge of the Surround (SR).
8. Glue a Mantel Wall (MW) in place.
9. Glue the other Mantel Wall (MW) in place.
10. Glue the Mantel Shelf (MS) in place.
11. Assembly of the fireplace is now complete.
Fireplace
1. Place Firebox Back (FBB) flat on the
work surface.
2. Glue a Firebox Wall (FBW) to the Fire-
box Back (FBB). The tab on the Firebox
Wall (FFW) fits into the slot on the Fire-
box Back (FBB).
3. Glue the Firebox Ceiling (FBC) to the
Firebox Back (FBB) and to the Firebox Wall (FBW).
4. Glue the other Firebox Wall (FBW) to the Firebox Back
(FBB) and to the Firebox Ceiling (FBC).
5. Use a damp clean cloth to wipe away any excess glue.
6. Let the glue set for a few minutes.
Parts Layout Diagram
2388 Pleasantdale Road, Atlanta, GA 30340 • 800-926-6464 • www.miniatures.com • Made in USA
1122
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
1
5
Bookshelf Parts Diagram Fireplace Parts Diagram
6 7
2 3 4
F
D
D
WS
S
S
SR
MW FBW FBWFBB MW
FBC MS
B
S
S
S
W
* The doors can be glued in place permanently or they can be made openable. Use
hinges or temporary adhesive (such as rubber cement) to leave the doors openable.
** The etched lines can be oriented towards the back if a smooth front finish is preferred.