minkaAire George Kovacs Artemis F803 User manual

V 3.0 Published on 08.2019

Artemis Installation Instructions
2 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Minka Aire product. To ensure correct function and safety, please read
and follow all instructions before assembly, installation and use of this ceiling fan. Please keep instructions
for future reference.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning the use of the appliance in a safe way and understand the
hazards involved. Cleaning and maintenance shall not be undertaken by children without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in accordance
with the wiring rules.

Artemis Installation Instructions
3 | P a g e
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to be
an all-pole disconnection to the ceiling fan electrical circuit, meeting
the requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch also must be placed in the same room as the
fan as per local wiring regulations AS3000
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 48kg.
7. The fan should be mounted so that the blades are at least 2.3 m above the floor in Europe or 2.1 m
above the floor in Australia.
8. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2
walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned
in a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty.
Mounting the fan in a situation where it is subject to water or moisture is dangerous and may increase
the risk of damage, injury or electrical shock and will void the warranty.
9. Must be assembled and installed by a licensed electrician.
10. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling
fan and contact the manufacturer, its service agent or suitably qualified persons.
11. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,
its service agent or suitably qualified persons.
12. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension
system shall be performed by the manufacturer, its service agent or suitably qualified persons.

Artemis Installation Instructions
4 | P a g e
PARTS LIST
•Unpack your ceiling fan carefully. Remove all parts and hardware.
•Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
•Check whether the ceiling fan has been damaged during transport. Do not operate/install any product
which appears damaged in any way. Return the complete product to the place of purchase for inspection,
repair or replacement.
•Examine all parts, you should have the following:
1. Fan blades x 3 11. Optional switch cup cover x 1
2. Hanger bracket x 1 12. Wall control incl. 2 mounting screws x 1
3. Canopy x 1 13. #10 x 38mm wood screws x 2
4. Canopy cover x 1 14. #8 x 19mm machine screws x 2
5a. Standard downrod assembly x 1 15. Lock washers x 2
5b. Minimum-length downrod
(for close to ceiling mounting only) x 1
16. 4mm star washers x 2
6. Coupling cover x 1 17. Washers x 2
7. Fan motor/housing assembly x 1 18. 4.8mm x 17mm screws x 10
8. Light kit mounting plate x 1 19. Flat washers x 10
9. 14W LED Light Kit x 1
10. Glass shade x 1
Fig. 1

Artemis Installation Instructions
5 | P a g e
ANGLED CEILING INSTALLATION
This fan hanging system supports a maximum 20 degree angled
ceiling installation. (Fig.2)
INSTALLING THE MOUNTING BRACKET
• The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing from the
tip of the blade to the nearest objects or walls.
• Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least 48kg,
with the two long screws provided. Ensure at least 30mm of the screw is threaded into the support. (Fig.3)
NOTE: The bracket screws provided are for use with wooden structures only. For structures other
than wood, the appropriate screw type MUST be used. Ensure the screws used are suitable for the
mounting surface and the surrounding environment.
Loosen the screw in the terminal block and remove the terminal block for later use. Secure the hanger bracket
to the ceiling joist or structure using the screws included. Re-install the terminal block back to hanger bracket.
(Fig.4)
Fig. 3
Fig. 2
Fig. 4

Artemis Installation Instructions
6 | P a g e
HANGING THE FAN
Loosen the two set screws and remove the hitch pin and lock pin from the top coupling of the motor
assembly. Do not discard keep these parts, they are required to reassemble later. (Fig.5)
Remove hanger ball and cross pin from downrod by loosening the set screw. Do not discard keep these parts,
they are required to reassemble later. (Fig.6)
Carefully feed the fan wires up through the downrod. Install the downrod into the top coupling of the motor
assembly. Line up the coupling holes with the downrod holes and install the lock pin and hitch pin. Secure
the down rod be tightening the set screws. (Fig.7)
Fig. 7
Fig. 6
Fig. 5

Artemis Installation Instructions
7 | P a g e
Slide the coupling cover onto the downrod and secure by tighten the two screws. Insert the canopy cover
and canopy onto the downrod. Carefully reinstall the hanger ball and cross pin onto the downrod and secure
by tightening the set screw. Take care not to twist or damage the wires. (Fig.8)
Lift the fan assembly onto the mounting bracket. Ensure the key slot (A) of the hanger ball is positioned on
the key pin (B) of the mounting bracket (C) to prevent the fan from rotating when in operation. (Fig.9)
Fig. 9
Fig. 8

Artemis Installation Instructions
8 | P a g e
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION MUST BE INCORPORATED IN THE FIXED WIRING
IN ACCORDANCE WITH THE WIRING RULES.
Carefully tuck the wire connections inside the outlet box or wall cavity if not using an outlet box. Use
the screws provided to secure the wall switch and wall plate to the outlet box or wall switch frame.
Fig. 10
Fig. 11

Artemis Installation Instructions
9 | P a g e
BLADE INSTALLATION
1. Remove the 3 blade screws, lock washers and flat lock washers set from the Lower Blade Holder.
2. Align and engage the top holes from one of the blades to the upper blade holder tabs.
3. Carefully align the bottom holes from the blade to the holes from the lower blade holder.
4. Secure blade with 3 screws, lock washers and flat lock washers provided (step 1).
5. Follow the same process for the remaining two blades.
6. All blade sets are grouped together by weight, because plastic materials vary in density, the fan may
wobble even though the blades are weight matched
NOTE: You must install the blades to the motor housing after mounting the motor to the ceiling.
NOTE: When installing more than one fan, ensure that the blades sets are not mixed up as each set is
dynamically balanced.
Fig. 12

Artemis Installation Instructions
10 | P a g e
INSTALLING THE LIGHT KIT
INSTALL THE LIGHT KIT MOUNTING PLATE
1. Remove 3 screws from the mounting ring.
2. Install the mounting plate onto the mounting ring and secure by tightening the 3 screws previously
removed from the mounting ring.
NOTE: Ensure the 3 screws are tighten and the earth wire of the mounting ring is connected.
INSTALL THE LIGHT PLATE
1. Remove the 3 screws from the mounting plate.
2. Raise and hold the LED light kit close to the mounting plate and join the connectors together.
3. Install the LED light kit onto the mounting plate and secure by tightening the 3 screws previously
removed from the mounting plate.
NOTE: The light source contained in this luminaire shall only be replaced by the manufacturer or his
service agent or a similar qualified person. DO NOT attempt to unscrew and open the cover on the LED
module.
Fig. 13
Fig. 14