MINOURA GRAVITYSTAND 2 User manual

GravityStand 2 instructions manual
1Insert Plastic Bracket into
each Leg.
Plastic Bracket
Leg
2Insert Metal Plate into
Lower Pillar, put Plastic
Cover onto each Leg, then
put through Guide Pin into
either hole for temporally
assembling.
Be sure the square holes on
Lower Pillar must face to
front side.
Lower Pillar
Guide Pin
Plastic Cover
Metal Plate
Leg
3Screw M6x40 Bolt into the
hole without Guide Pin.
(You don't need to tighten
the bolts so much now.)
M6x40 Bolt M6x40 Bolt
4
!
GravityStand is designed to keep
enough stability. But we highly
recommend you to x the stand
to the wall with the supplied strap
M3.5x15 or 25
Screw
to prevent any
accident.
Cradle Hook is
padded with soft
urethane to protect
your bike nish.
Angle & position
are adjustable.
Cradle height is
adjustable in 3
positions without
requiring any tool.
Setting up is very
easy! Just lean to
the wall.
(Pillar should be set
parallel to the wall)
Remove Guide Pin.
Remove
5Screw M6x40 Bolt to
another hole.
M6x40 Bolt M6x40 Bolt
6Tighten all M6x40 Bolts
rmly.
7Install Metal Plate to the
top holes on Lower Pillar
with M6x12 Bolt.
Metal
Plate
M6x12 Bolt
- Page 1 -

8Joint Upper Pillar to the
installed Metal Plates.
Make sure the square holes
on Upper Pillar align the
same.
Tighten M6x12 Bolt rmly.
Lower Pillar
Upper
Pillar
M6x12 Bolt
9Install Cradle Base to your
favorite hole.
Hook both ends to the
square holes then slide
down to x.
Cradle Base
10
Push Lock Lever toward
the pillar to lock Cradle
Base position.
To change Cradle Base
position, pull back Lock
Lever then pull out the
cradle.
11
Lock Lever
Use screwdriver
to release Lock
Lever. Do NOT do
with your nger,
otherwise your nail
may be damaged.
!
Assemble Bike Cradle.
Angle Adjust
Plate
Cradle Bar
Cradle Hook (universal)
M6x14 Bolt
M6x20 Bolt
Flat & Spring
Washers
Set Angle Adjust Plate as the long
hole is set downward.
Cradle Hook must be installed
from back of Cradle Bar to
prevent scratching problem to
your bike frame.
12
Bike cradle is angle adjustable to
t to your bike's top-tube angle.
Loosen the lower bolt (long hole
side) to adjust. After that tighten
the bolt rmly.
The bike should be as horizontal
as possible.
Set and lean GravityStand to the
wall.
The pillar must be set parallel to
the wall to keep best stability.
Put the top-tube of your bike on
Cradle Hooks gently.
Do NOT apply any paper
or thin plate under Legs to
prevent slippage accident.
!
13
Each position and angle of Cradle
Hook is also adjustable.
IMPORTANT NOTES
• Gravity Stand is only for normal
2-wheel bikes. Do not use for any
other purposes.
• Gravity Stand will not supported
nor xed. Be careful not to hit the
stand when you passing nearby.
• Gravity Stand is designed to keep
enough stability even having heavy
shocks. But we highly recommend
you to x the stand to the wall with
the supplied strap.
• Remove any sand and dust from
the area Leg touches to prevent
slippage problem.
• Check every bolt regularly and
tighten rmly with proper tool if you
nd any loose.
• Minoura offers 1-year limited
warranty from the date of your
purchase. Any problem caused
by manufacturer's defect and
wrong workmanship will be
covered by this program. But any
trouble caused by user's misuse,
unapproved modication, natural
calamity and every problem
happened during shipment will
NOT be covered by Minoura.
For more detail, please refer the
attached "Warranty Program
Instruction" card.
FOR MORE INFORMATION
If you have any quetion, contact the
shop where you purchased or your
local distributor rst.
MINOURA JAPAN
1197-1 Godo, Anpachi, Gifu 503-2305
Phone [phone]
Fax [phone]
Mail [email protected]
Web www.minoura.jp
MINOURA NORTH AMERICA
Mail [email protected]
Made in Japan
- Page 2 -