Mira Platinum User manual

1
Mira Platinum Wireless Controller User Guide

2
CONTENTS
Introduction .............................................................................................3
General................................................................................................. 3
Safety Information...................................................................................3
Control Layout.........................................................................................4
Display Symbols......................................................................................5
Using the Shower ....................................................................................6
Switch On/Off .......................................................................................6
Adjust Temperature ..............................................................................7
Adjust Flow...........................................................................................7
Functions .................................................................................................8
Function Menu.........................................................................................9
Enter the Function Menu......................................................................9
Exit the Function Menu.......................................................................10
Changing Functions/Settings .............................................................. 11
Maximum Showering Water Temperature .......................................... 11
Eco ................................................................................................ 12
Warm-Up ............................................................................................13
Clock Display......................................................................................15
Flow Range ........................................................................................ 16
Control Frequency..............................................................................18
Replacing the Batteries ........................................................................19
Fault Diagnosis......................................................................................20
Error Codes........................................................................................20
General Faults....................................................................................22
Cleaning .................................................................................................24
Disposal and Recycling ........................................................................24
Notes ......................................................................................................25
Customer Service..................................................................................28

3
General
Thank you for purchasing a quality Mira product. To enjoy the full potential of your
new product, please take the time to read this guide thoroughly and keep it handy
for future reference.
The Mira Platinum Wireless Controller is a remote user interface and controls the
following functions:
• Showering Water Temperature
• Showering Water Flow
• Maximum Showering Water Temperature
• Eco Mode
• Warm-Up Mode
• Clock
• Flow Range
This guide covers the setting and use of these functions and includes a trouble
shooting guide should the appliance not function as expected. For issues relating
to the installation of the appliance or other associated products, please refer to the
relevant Installation Guide(s) or contact our Customer Services Team. (Details in
the back of this guide.)
NOTE! ALL FUNCTIONS ARE ONLY AVAILABLE AFTER THE CONTROLLER
HAS BEEN ASSIGNED TO A MIRA PLATINUM DIGITAL MIXER VALVE. (See
Mira Platinum Installation Guide.)
INTRODUCTION
SAFETY INFORMATION
1. Make sure that you fully understand how to operate this shower and make sure
that it is properly maintained in accordance with the instructions given in this
manual.
2. Sunburn or skin conditions can increase your sensitivity to hot water. Make sure
that you set the shower to a cooler temperature.

4
Turn Outer Ring
Showering Water Flow Adjustment
Decrease
Flow
Increase
Flow
Increase
Temperature
Decrease
Temperature
Display Start/Stop
CONTROL LAYOUT

5
Flow Display
Low Battery
Display
Control Out Of
Range
Temperature Display
Clock Display
Economy Flow
Display
DISPLAY SYMBOLS

6
Press “ ” to start or stop shower.
Temperatureandowsettingswillbesameaswhenlastused.
After a short period, display will dim to help extend battery life.
Approximately 10 minutes after shower has stopped, display will turn off
automatically.
Shower will not run continuously for more than 30 minutes before stopping
automatically (5 minutes when “ECO” function is set to “on”).
When “Warm-Up” function is “on”, there will be a short delay (5 seconds) before
waterowsfromshower.
USING THE SHOWER
Switch On/Off

7
Adjust Temperature
While shower is running, press “ + ” or “ - ” to adjust temperature. Showering
temperature appears on display in degrees Celsius (°C).
Adjust Flow
Turnouterringclockwiseoranticlockwisetoadjustow.Showeringowlevel
appears on display in white bars.

8
FUNCTIONS
F1 - Maximum Showering Water Temperature. This is the temperature the shower
cannot go beyond when in use.
F2 - Eco. The shower will stop automatically
after 5 minutes. When this setting is “on”,
maximumavailableshoweringowislimited
to half the ow normally produced. “ECO”
symbol is displayed. When setting is “off”,
maximumshoweringowwillbeatfullow.
“ECO” symbol goes out when more than half
owisselected.
F3 - Warm-Up. When this setting is “on”
and the shower is started, there is a short
delay (5 seconds) before water ows and
temperature display will ash to indicate
shower is waiting for selected display
temperature to be achieved. When shower
stops, temperature has been reached and
shower is ready for use, press “ ” as normal.
If temperature cannot be found, shower will
stop automatically after 5 minutes.
When “Warm-Up” setting is “off”,temperaturedisplaywillnotashandshoweroperates
as normal.
Note! When used with some combination boilers, the warm-up function may be impaired.
This is due to the functional nature of combination boilers.
F4 - Clock Setting. To set the time.
F5 - Clock Display. When Clock Display
is “on”, time is displayed when shower has
stopped, or after 10 seconds of inactivity
whilst the shower is running. When Clock
Display is “off”, the time is replaced by the
showering temperature.
F6 - Flow Range. For use with High
Pressure/CombiValveversiononly.Thewaterowrate(showeringforce)canbeadjusted
to within a desired range by setting a low point and a high point. During adjustment the
shower will need to be started.
F7 - Control Frequency. An unreliable functioning of the appliance (not always able to
change settings of shower) may indicate radio interference by another device transmitting
locally on same channel. Changing channel may resolve this problem.
The following functions can be altered individually to adjust how the shower operates:
on off

9
Press “+” and “ ” buttons simultaneously
until “End” is displayed on the unit.
Use “+” or “-” buttons to cycle
through functions and press
“ ” to enter setting.
(See following sections in this guide
for details on each function and how to
alter their settings.) Note! If signal loss
occurs during a function change, “Err”
will appear on display.
Press “ ” to clear and retry function
change.
FUNCTION MENU
Enter the Function Menu

10
Exit the Function Menu
Whennished,use“+” or “-” buttons to
cycle back through functions until “End”
appears. Press “ ” to exit.
Control is ready to use.
If necessary, test shower to see if
functions are working as expected.

11
Press “+” or “-” to adjust temperature.
Maximum = 48°C
Minimum = 35°C
Cycle menu to “F 1” and press
“ ”.
Factory default “45°C”.
Press “ ” to set.
Press “ ” to exit back to Function
Menu. See section “Exit the Function
Menu”.
CHANGING FUNCTIONS/SETTINGS
Maximum Showering Water Temperature

12
Press “+” or “-” to change setting
“on” or “off”.
Factory default “off”.
Press “ ” to exit back to Function
Menu. See section “Exit the Function
Menu”.
Cycle menu to “F 2” and press
“ ”.
Press “ ” to set.
Eco

13
Warm-Up
Press “+” or “-” to change setting “on”
or “off”.
Factory default “off”.
Note! Function will not work with combination boilers.
Press “ ” to exit back to Function
Menu. See section “Exit the Function
Menu”.
Cycle menu to “F 3” and press
“ ”.
Press “ ” to set.

14
Clock Setting
Press “-” to change hour setting.
Press “+” to change minute setting.
Cycle menu to “F 4” and press
“ ”.
Press “ ” to set time and exit back to
Function Menu. See section “Exit the
Function Menu”.
Factory default “4:00”.
Note! Can also be activated by disconnecting and reconnecting battery.

15
Clock Display
Cycle menu to “F 5” and press
“ ”.
Press “+” or “-” to change setting “on”
or “off”.
Factory default “on”.
Press “ ” to set.
Press “ ” to exit back to Function
Menu. See section “Exit the Function
Menu”.

16
Flow Range
For use with High Pressure/Combi Valve version only.
Factory default “1 - 99”
Cycle menu to “F 6” and press
“ ”.
“on” is displayed, press “ ” to start
shower.
Lower limit is displayed, e.g.
“L 1”.Adjustowtodesiredlowerlimit
1-99.
Press “ ” to set lower limit.

17
Higher limit is displayed, e.g.
“H 23”.Adjust ow to desired higher
limit 1-99. (Most plumbing systems may
achievemaximumowbefore99.)
Press “ ” to set higher limit.
Press “ ” to set and exit back to
Function Menu. See section “Exit the
Function Menu”.

18
Control Frequency
Cycle menu to “F 7” and press
“ ”.
Press “+” or “-” to change channel “1-7”.
Factory default “1”.
Press “ ” to set.
Press “ ” to exit back to Function
Menu. See section “Exit the Function
Menu”.

19
Press button to release and remove
control from wall.
To access the batteries, the control unit must be removed from the wall. Make sure
control unit is dry before removing.
Turn unit over to access batteries.
Remove and replace all batteries.
Only use new batteries of same make
and type. Do not use rechargeable
batteries.
Hook control on top of bracket and
push rmly until control “clicks” back
into place.
If necessary, test shower to see if
functions are working as expected.
REPLACING THE BATTERIES

20
Error Codes
Aspecicproblemrelatingtotheelectronicfunctionoftheshowerwillresultinan
error code being displayed on the control.
Over Temperature at Control Sensor
1. Turn Digital Mixer off for 10 seconds. Turn back on and allow
15 seconds to reset.
2. If shower operation does not return to normal, make sure hot
and cold inlets are not reversed.
3. If shower operation does not return to normal, make sure inlet
ltersandcheckvalvecartridgesareclean.
4. If shower operation does not return to normal, check the water
supplies to the valve are within the correct temperature and
pressure ranges. See “Mira Platinum Installation Guide -
Specications”.
5. If problem still occurs, make a note of the error code and
contact our Customer Services Team.
Control Sensor
1. Turn Digital Mixer off for 15 seconds. Turn back on and allow
15 seconds to reset.
2. If shower operation does not return to normal, replace
Thermistor. (To be performed by competent tradesperson
only!)
3. If problem still occurs, make a note of the error code and
contact our Customer Services Team.
FAULT DIAGNOSIS