Miracle 461R User manual

DNA Climber w/Ropes
DNAClimber w/Ropes
Page 1 of 6
461R
27JAN20
Rev. G
1. Concrete for footings, wheelbarrow or mixer, 5 gallon bucket, water supply
2. Digging equipment for footings (spade shovel, post hole digger, auger)
3. Bracing materials (2x4s, sawhorses, etc.)
4. Tape measure and level
5. Open end wrench set,Allen and 6-lobe wrenches or bits, socket set, screwdrivers
6. Drill, bits, extension cords, power supply
7. Step ladder
8.Adult installers - 2 minimum
TOOLS AND EQUIPMENT REQUIRED
Refer to "Installations 101"
Installation Guide
461R
Note:An (*) by a part number (CODE) indicates: Color Code Required.
IMPORTANT! Prior to installation of any components, refer to the "Owner/Operator Manual". This
manual will provide important information pertaining to site preparation, footings, system stabilization and
other necessary information vital to the success of your installation.
DNAClimber w/Ropes
ProtectiveArea: 32' x 16'

Page 2 of 6
DNA Climber w/Ropes
DNAClimber w/Ropes
461R
27JAN20
Rev. G
STEP 2 SECURE SPLICE WELDMENT INTOARCH HALVES
Top View
Footing Layout
Note: 12" of protective surfacing is required above footings.
1a. Dig footing holes per Footing Layout. Refer to Footing Details installation located
behind Installations 101 in Installation Manual.
STEP 1 DIG FOOTINGS

DNA Climber w/Ropes
DNAClimber w/Ropes
Page 3 of 6
461R
27JAN20
Rev. G
STEP 3 ATTACH VERSALOK CLAMPOVERARCH CONNECTION POINT
THIS SPACE INTENTIONALLY LEFT BLANK

Page 4 of 6
DNA Climber w/Ropes
DNAClimber w/Ropes
461R
27JAN20
Rev. G
STEP 4 THREAD ROPE-TWISTED ARCH ONTO CLIMBER
4c. Continue threading the rope-twisted arch, one section at a time, through the rungs;
tighten the rope-twisted arch, at each section, before securing with set screws.
4a. Begin at one end of the climber and thread the rope-twisted arch into the first sphere
approximately 4", OR, until you feel the rope-twisted arch bottom out inside the
sphere.
4b. Secure the rope-twisted arch with PN 104285; set screw should come in contact with
the rope end ferrule. IF, the set screw comes in contact with the "rope", then use PN
104073.
Note: This applies ONLYto the four (4) ends of the climber.

DNA Climber w/Ropes
DNAClimber w/Ropes
Page 5 of 6
461R
27JAN20
Rev. G
STEP 4 THREAD ROPE-TWISTED ARCH ONTO CLIMBER cont.
4d. Make sure the rope-twisted arch is inserted into the correct rungs at the cross-over
point.
4e. Repeat all of Step 4 for second rope-twisted arch
5a. Raise the climber and place legs into footings; brace into position, level and plumb.
Pour concrete and allow to cure for 72 hours prior to allowing play.
STEP 5 RAISE CLIMBER AND SET INTO FOOTINGS
Proceed with FinalAssembly installation located behind Installations 101 in the Installation
Manual.
FINAL STEP
Bill of Materials
MODEL 461R DNACLIMBER W/ROPES
QUANTITY PART NUMBER DESCRIPTION
2 996243* ARCH-ROPE HALF
1 912291* PARTS CARTON 461R
1 116048 LABEL, 2" X 2" WHITE POLYESTERTHERMAL
1 116049 LAMINATE, CLEAR, 2" X 2" W/PERMANENT
1 986348 PARTS CARTON - GENERICAND WARNING LABELS
1 994991 PARTS CARTON - 5-12 LABEL
1 999033* PARTS CARTON - TOUCH-UP PAINT-POST
1 907326* PARTS CARTON 461R

Page 6 of 6
DNA Climber w/Ropes
DNAClimber w/Ropes
461R
27JAN20
Rev. G
Bill of Materials cont.
PARTS CARTON 912291*
QUANTITY PART NUMBER DESCRIPTION
2 996244* ROPE-TWISTEDARCH
1 996233 SPLICE WELDMENT
1 HW912291-1 HRDW PKG 461R S1/1
HW912291-1 HRDW PKG 461R S1/1
QUANTITY PART NUMBER DESCRIPTION
72 104073 SET SKT3/8-16 X 1/2 BOLT 18-8 SS
4 104286 BOLT3/8-16 X 1 BHCS 6 LOBE 18-8 SS
2 104749 BOLT1/4-20 X 1-1/4 BHCS 6 LOBE 18-8 SS
4 104285 SET SKT3/8-16 X 3/8 18-8SS
PARTS CARTON 986348
QUANTITY PART NUMBER DESCRIPTION
1 116021 LABELMIRACLE ID - GENERIC
1 116022 LABELWARNING - PLAYGROUND - ENGLISH
1 713550 STICKER TOP OF SURFACING
1 116099 LABEL, PLAY SMART RULES
PARTS CARTON 994991
QUANTITY PART NUMBER DESCRIPTION
1 116037 LABEL-AGES 5-12 YEARS MREC
PARTS CARTON 999033
QUANTITY PART NUMBER DESCRIPTION
1 115208* PAINT 4.5 OXAEROSOLCAN TOUCH UP
PARTS CARTON 907326*
QUANTITY PART NUMBER DESCRIPTION
2 999115* CLAMP RING HALF-5" DIANO LOGO F/LF