miseno MT6030FSDS User manual

PAGE 1
MT6030FSDS
60” Acrylic Double Slipper Freestanding Bathtub
INSTALLATION MANUAL
• Carefully read the instructions before starting the installation
• This bathtub should be installed by an experienced plumber
• Waste pipe and drain trap are not supplied. Connect to an existing drain pipe.
If you are missing any parts, please stop and contact us immediately 1-855-480-2915
ATTENTION

PAGE 2
TOOLS REQUIRED
CAUTION
You will need at least two people to
install this product properly.
In order to reduce the risks of personal
injuries, do not support or lift the
bathtub by the rim. Provide adequate
support under the feet.
Thedistributorisnotresponsibleforany
damage to the unit or personal property
caused by improper installation. If you
disregard instructional warnings, you
will void your warranty and possibly
deal with water damage.
• Unpack and inspect the bathtub for
damage. Return the bathtub to the
carton until you are ready to install.
• Install the bathtub on an adequately
supported, level floor.
• Before installation, ensure proper
access to the final plumbing
connections.
Pencil Level Silicone
Measuring Tape
Drill
Adjustable key Hole saw
Plus:
Fabric cloth to protect the bath.

PAGE 3
SPECIFICATION
47.6gal
0.18m355lbs
25kg
60”[1524]
22 7/8”[582]
10 5/8”[269]
19 7/8”[505]
16 7/8”[430]
13 3/4”[350]
Measures: inch [millimeter]
2”[50]
Drain
18 7/8”[480]
40 7/8”[1038]
29”[737]
23 7/8”[605]
57 1/4”[1454]

PAGE 4
FLOOR TRACING TEMPLATE
20 1/4” [514mm]
19 1/8” [485mm]
18 1/2” [469mm]
9 7/8” [252mm]
6 3/4” [173mm]
13 5/8” [347mm]
19 3/4” [502mm]
26 1/8” [662mm]
27 1/4” [692mm]
30” [762mm]
60” [1524mm]
29” [737mm]
32 3/4” [832mm]
33 7/8” [862mm]
40 1/4” [1022mm]
46 5/16” [1177mm]
Rough-in zone for water supply pipes
Zone for P-Trap & Waste Outlet cut-out
Extra zone for P-Trap & Waste Outlet cut-out
Drain 21 1/4” [539mm]
22 3/4” [579mm]

PAGE 5
PART DESCRIPTION
Flexible Tube (NOT SUPPLIED) or Standard P-Trap (NOT SUPPLIED)
P-Trap (NOT SUPPLIED)
Adapter (SUPPLIED)
PARTS
PREPARATION
1A 1B
1A. Use the floor tracing template supplied in this manual to trace the proper position of your supply
pipes, your drain and your P-Trap rough-in.
OR
1B. Place the bathtub in the desired position on the floor, manually locate the proper position for your
plumbing and trace the outline on the floor.
2. Place the tub in the desired position and level it using the adjustable feet.
3. Remove the bathtub and put it on a throw rug to prevent damage.
IMPORTANT
• Drawings are for reference ONLY.
• This guide illustrates installation best practices.
• Carefully read the instructions before starting the installation.
• This bathtub should be installed by an experienced plumbing
• Make sure the floor drain is already installed and is compliant with your local regulations.
• Piping and drain trap are not supplied.

PAGE 6
FAUCET INSTALLATION ON THE BATHTUB (OPTIONAL)
4 3/4” [120]
1 3/8” [35]
2” [50]
Measures: inch [millimeter]
Zone for deck Mounted faucet
4 3/4” [120]
15” [380]
1. Locate where you will drill the holes into the acrylic, and stick masking tape onto that area. This will
prevent the acrylic from chipping, and protect the finish from scratches.
2. Drill holes for the faucet in the bathtub at the desired location.
3. Unscrew the bolts at the bottom of the bathtub using an adjustable wrench. Then carefully take out
the top of the tub and place it on a throw rug or other protective floor covering to prevent damage to the
bathtub and the floor.
4. Install the faucets according to the faucet manufacturer’s instructions. Then assemble the top of the
bathtub with the skirt, and secure the bolts at the bottom as shown in the illustration.
5. Connect the faucet supply lines with hot and cold water supplies and check for leaks.
Notes: Verify all pipe connections to ensure no leakage occurs.

PAGE 7
Installation using a standard PVC P-Trap
is done similarly.
INSTALLATION (Option #1)
GUIDELINES FOR BATHTUB DRAIN INSTALLATION
Option #1
1. Install the P-Trap by screwing it to the preinstalled bathtub drain outlet. Use Teflon tape and/or
sealant. Then, as shown in the illustration, connect the P-Trap to the Flexible Tube.
2. Connect the Flexible Tube to your existing floor drain as illustrated, using PVC pipe sealant to
join the parts together.

PAGE 8
Installation using a standard PVC P-Trap
is done similarly.
INSTALLATION (Option #2)
Option #2
1. Screw the supplied Adapter to the preinstalled bathtub drain. Use Teflon tape and/or sealant to
seal the threads.
2. Connect the P-Trap to the Adapter using PVC pipe sealant to adequately join the two parts.
3. Then, as shown in the illustration, connect the P-Trap to the Flexible Tube.
4. Connect the Flexible Tube to your existing floor drain as illustrated, using PVC pipe sealant to
join the parts together.

PAGE 9
SECUREMENT
24h
BEFORE AFFIXING YOUR TUB TO THE FLOOR, MAKE SURE YOU HAVE INSTALLED
YOUR FAUCET (IF APPLICABLE) AND THAT YOU HAVE CHECKED FOR LEAKS.
1. Test for leaks by filling up the tub and let it drain. Then check all plumbing connections for leaks.
2. Fix the bathtub to the floor by applying a strong Tub & Tile Adhesive under each edge of the tub that
will be in contact with the floor: The rim, the lateral bars and the feet.
3. Finally, for a professional finish, draw a bead of silicone around the base.
4. Let silicone dry for 24 hours before use.