MISS LIGHTING ML-ML28B User manual

56*10W 4in1 zoom moving head light
User Manual
ML-ML28B

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
1
TABLE OF CONTENTS
1. Safety Instructions....................................................................................................1
2. Technical Specifications..........................................................................................2
3. How To Control The Uni t ......................................................................................3
4. Trouble shooting.......................................................................................................7
5. Fixture Cleaning........................................................................................................7
6 . Technical Support ....................................................................................................8
statement
The product has well capability and intact packing when leave factory. All of
the user should comply with warning item and manual, any misuse cause of the
damages are not included in our guarantee, and also can not be responsible
for any malfunction & problem owing to ignore the manual.
1. Safety Instructions
Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
 Unpack and check carefully there is no transportation damage before using the unit.
 Before operating, ensure that the voltage and frequency of power supply
match the power requirements of the unit.
 It’s important to ground the yellow/green conductor to earth in order to avoid
electric shock.
 The unit is for indoor use only. Use only in a dry location.
 The unit must be installed in a location with adequate ventilation, at least
50cm from adjacent surfaces. Be sure that no ventilation slots are blocked.
 Disconnect main power before replacement or servicing.
 Make sure there are no flammable materials close to the unit while operating as it is fire
hazard.
 Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but
always by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is
higher than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing
bare-hand during its operation. Turn off the power and allow about 15 minutes for the unit to
cool down before replacing or serving.
 In the event of serious operating problem, stop using the unit immediately.Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
2
or malfunction. Please contact the nearest authorized technical assistance center.
Always use the same type spare parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.
Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they
are visibly damaged.
Caution:
There are no user serviceable parts inside the unit. DO NOT open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
your nearest dealer.
Installation:
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is
firmly fixed to avoid vibration and slipping while operating. And make sure that
the structure to which you are attaching the unit is secure and is able to support a weight of
10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out of
the touch of people and has no one pass by or under it.
2. Technical Specifications
Light Sources: 56 x 10W 4in1 RGBW LED
Beam Angle: 10°-60°
Power Consumption: 600W
Power Voltage: AC 100-240V, 50/60Hz
Dimension: 37*27*22cm
Packing Dimension: 47*38*50cm
Net Weight: 10Kgs
Gross Weight: 13Kgs
Control
DMX Channel: 14Channel
Control Modes: DMX

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
3
Pan/Tilt
Pan/Tilt: 540°/ 270°
Pan/Tilt Resolution: 16 bit
Construction
Display: LCD Display
Data In/Out socket: 3-pin XLR sockets
Power Socket: Powercon in
Protection Rating: IP20
Features
Motorized liner zoom system, zoom range: 10°~60°
Outstanding color macro effect
Dimmer: 0~100% smooth dimming
Variable strobe effects
Fast, quiet operation and flicker free
The lumen derails like below:
10°
1M
3M
5M
R
Lux
437
82
34
G
Lux
5500
881
348
B
Lux
4300
845
370
W
Lux
4200
824
285
RGBW
（10°）
Lux
14500
2655
893
RGBW(60°)
Lux
6.9 K
983
462
3. How To Control The Unit
The DMX512 is widely used in intelligent lighting control,with a DMX 512
controller.connect several lights together,dmx in and dmx out,
3 pin XLR connectors: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
4
Display:
MENU To select the programming functions
DOWN To go backward in the selected functions
uP To go forward in the selected functions
ENTER To confirm the selected functions
Set DM X Address Code
1 Press "Menu" to "Set DMX Address",and press"ENTER" keys to enter into
2 Show "Set DMX Address DMX Address:001",Press the "UP and DOWN"
keys to amended
3 Press "ENTER"keys to save and Exit,Press the"MENU"Keys does not save and Exit
function
Address
CH Value
Set to Slave
Auto program
Music control
Address001~XXX
PAN……
Slave
Master-Auto / Alone-Auto
Master-Music / Alone-Music
Change address
Show each channel value
Slave receive position
select
auto run mode
Sound auto run
inform
Temp Inf
Head
Temperature
XXX℃/℉
current tempreture
Soft Inf
V1.0……
software version
Person
Status settings
Pan Reverse
Tilt Rev
P-Degree
Feedback
Movement
Speed
Mic Sensitivity
ON/OFF
ON/OFF
540/360
ON/OFF
Speed 1~ 2
0~99%
Pan scan opposition
title scan opposition
scan angle select
scan the Measuring dish
play a part or not
scan mode select
mic sensitivity
Fans Control
Auto Speed
High Speed

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
5
Display Settings
Shut off
show close delay time
Reset Default
ON/OFF
Re-load all delivery
parameter
Reset
Reset All
Reset the light
Adjust
Test Channel
PAN…
:
Channel test
:
Stati Control
PAN
PAN=XXX
Manually test channels
Calibrate Values
Password
PAN
TILT
Password=XXX
PAN=XXX
TILT
channels’ data calibrate
code :050
PAN channel data
calibrate
TILT channel data
calibrate
DMX channel´s functions and values (14 DMX channels):
DMX functions and their values (14 DMX channels):
Channel
Value
Function
1
PAN Movement 8bit :
0-255
Pan Movement
2
Pan Fine 16bit
0-255
Fine control of Pan movement
3
TILT Movement 8bit :
0-255
Tilt Movement
4
Tilt Fine 16bit
0-255
Fine control of Tilt movement
5
Red LED :
0-255
Red ( 0-Black , 255-100% Red )
6
Green LED :
0-255
Green ( 0-Black , 255-100% Green )
7
Blue LED :
0-255
Blue ( 0-Black , 255-100% Blue )
8
White LED :
0-255
White ( 0-Black , 255-100% White )
9
Shutter, strobe:
0-31
Led trun off
32-63
Led turn on
64-95
Strobe effect slow to fast
96-127
Led turn on
128-159
Pulse-effect in sequences
160-191
Led turn on
192-223
Random strobe effect slow to fast

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
6
224-255
Led turn on
10
Dimmer intensity:
0-255
Intensity 0 to 100%
11
Rainbow:
0-4
No function
5-29
R
30-54
G
55-79
B
80-104
W
105-129
Rainbow colours
130-154
Rainbow colours
155-174
Rainbow colours
175-179
Rainbow colours
180-184
Rainbow colours
185-189
Rainbow colours
190-210
Rainbow colours
211-255
Crossfading colours from slow to fast
12
Zoom Movenment 8 bit
0-255
Zoom movement
13
Speed Pan/Tilt movement:
0-225
max to min speed
226-255
no function
14
reset, internal programs:
0-79
Normal
80-84
All motor reset
85-87
Scan motor reset
88-99
No function
100-119
Internal program 1 (secne1~8 of EEPROM) 2700k
120-139
Internal program 2 (secne9~16 of EEPROM) 3200k
140-159
Internal program 3 (secne17~24 of EEPROM) 4300k
160-179
Internal program 4 (secne25~32 of EEPROM) 5600k
180-199
Internal program 5 (secne33~40 of EEPROM) 6500k
200-219
Internal program 6 (secne41~48 of EEPROM) 7200k
220-239
Internal program 7 (secne49~56 of EEPROM) 8000k
240-255
Music Control (secne of Program 1)

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
7
4. Trouble shooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The un it does no t work , no li ght a n d t he f a n d o es no t w o r k
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. N o t responding t o D MX c on t ro ll er
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on
PCB of the unit or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may cause
damage or interference to DMX interface circuit.
C . One of the cha nn el s is no t w o r k ing w el l
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
5. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
 Cle a n with s oft clo th u s ing no r m a l g l a ss clea ni ng fluid .
 A lw a y s d r y th e parts ca r ef ully .
 Cle a n th e ex ter na l optic s a t leas t ev ery 20 days. Cle a n th e in ter na l opti cs a t lea s t ev ery
30/60 days.

Guangzhou Miss Lighting Technology Co.,Ltd
56*10W zoom moving head light
8
6.Technical Support
Support Telephone: [phone]
Support Email: [e-mail]
Website: www.gzmisslighting.com
Working Time: (BeiJing Time)
Monday to Friday 08:00~12:00 14:00~18:00 19:00~21:00
Saturday 09:00~12:00 14:00~18:00
Note: all the rest of China's holidays