Mistral MIR068 User manual

Model: MIR068
Instruction Manual
2400W Steam Iron

2
Important Safeguards
Read all instructions carefully, even if you are
quite familiar with the product. Please retain these
instructions for future reference.
In order to reduce the risk of re, electric shock,
and/or injury, basic safety precautions should
always be followed when using mains-powered
products. These include:
• Check that the voltage of the main circuit
corresponds with the rating of the appliance
before operating.
• DO NOT immerse cords, plugs or any part of
the appliance in water or any other liquid.
• The iron should always be switched off before
connecting or disconnecting from the power
supply. To unplug, grasp the plug and pull from
the power socket. Never pull the iron or carry it
by the cord.
• DO NOT pull the plug out by the cord, as this
may damage the plug and/or the cable.
• If the supply cord or appliance is damaged,
stop using the appliance immediately and
seek advice from the manufacturer or its
service agent or a similarly qualied person.
• Do not attempt to repair or disassemble the
appliance. There are no user-serviceable parts.
• DO NOT let the cord hang over the edge of
a table or counter, or let it come into contact
with any hot surfaces.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that
they do not play with the appliance.
• Cleaning and user maintenance shall not be
made by children without supervision.
• The use of accessory attachments is
not recommended by the appliance
manufacturer, apart from those supplied with
this product. DO NOT use extension cords with
the appliance.
• If you are leaving the iron momentarily, always
switch it off, remove the plug from the wall
socket, and stand the iron upright.
• Only use normal tap water or distilled water in
this product.
• Never direct steam toward people, pets or
electrical systems.
• DO NOT leave the iron unattended when
connected to the mains or on an ironing
board.
• When you have nished ironing or when
you are leaving the iron unattended: Press
the steam dial to [0] position, and the
temperature control dial to the ‘OFF’ position.
Stand the iron upright and disconnect the
appliance from the mains socket.
• DO NOT place the iron on an unprotected
surface.
• Stand the iron on its heel on a level, stable,
heat-resistant surface.
NOTE: Some parts of the iron have been
slightly greased and as a result, the iron
may smoke slightly when switched on for
the rst time. This should not occur after
the rst few uses.
• Do not place any part of this appliance on or
near a hot gas or electric burner.
• Burns can occur from touching hot metal
parts, hot water or steam. Be careful when
you turn the iron upside down to empty
excess water from the tank, as this will be hot.
• Do not allow the power cord to touch hot
surfaces, and always ensure the cord is
adequately constrained. Let the iron cool
down completely before storing away.
• Only pick up the appliance by its handle, as
certain parts of the appliance become hot
during use.
• Ensure that the iron’s soleplate does not
become damaged by rough surfaces or
sharp objects, e.g. zips.
• Always switch off and disconnect the power
plug from the wall socket before lling the iron
with water, or pouring the remaining water
out. It is recommended that the water be
emptied after every use.
• To avoid an overloaded circuit, do not
operate another high wattage appliance on
the same electrical circuit.
• Do not use the iron for anything other than
its intended use. This product is intended for
household use only.
• Do not add vinegar, perfumed water or any
chemical-based liquids into the water tank,
as doing so can seriously damage the iron.
• Do not use outdoors.
• The iron must be used and rested on a stable
surface.

3
• When placing the iron on its stand, ensure
that the surface on which the stand is placed
is stable.
• The iron is not to be used if it has been
dropped, if there are visible signs of damage
or if it is leaking.
Warning
If the supply cord is damaged, the cord must be
replaced by the manufacturer, its service agent
or similarly qualied persons in order to avoid a
hazard.
This product has not been designed for any uses
other than those specied in this booklet.
Save These instructions

4
Features of your Steam Iron
Measuring cup
Ceramic soleplate,
ensures a smoother glide
over your clothing
Cord bushing
Power indicator light
Hot-steam
button
Auto shut-off
indicator light
Spray button
Steam dial
Filler door (Water Inlet)
S p r a y N o z z l e
Soleplate
Maximum Mark
f o r W a t e r L e v e l
Clean out
button
Variable
Temperature
Control
Transparent
water tank

5
Your Steam Iron
Before using your new Steam Iron, it is important
that you read and follow the instructions in this
booklet, even if you feel that you are quite
familiar with this type of appliance. Find a place
to keep this booklet handy for future reference.
Your attention is drawn to the section dealing
with Important Safeguards.
This appliance has been designed to operate
from a standard domestic power socket. It is not
intended for industrial or commercial use.
Before First Use
When using the iron for the rst time, test it on an
old piece of fabric to ensure that the soleplate
and water tank are completely clean. When
using the iron for the rst time, you may notice a
slight emission of smoke and hear some sounds
made by the expanding plastics. This is quite
normal and it stops after a short time.
How to use your
Steam Iron
Filling the tank with water:
CAUTION! Before lling the tank with water, make
sure the appliance is unplugged.
• This iron can be used with normal tap water.
• Use the water measuring cup to ll the tank.
Never ll directly from the tap.
• If the water in your area is particularly
hard, it is recommended to use distilled or
demineralised water.
• Do not put vinegar, starch, chemicals,
de-scaled water or de-scaling agents in the
water tank.
• Remove the mains plug from the wall socket
before ling (or emptying) the iron with water.
NOTE: Wait for the iron to cool down
before emptying or lling the water tank.
• Press the steam dial to [0] position, and
the temperature control dial to the ‘OFF’
position.
• Open the ller cap of water inlet.
• Place the iron on the heel rest and tilt forward
at a 45° angle to help the water enter the
opening without over owing.
• Pour water into the water tank opening
and ll up to the maximum (MAX.) level and
taking care not to go over the maximum level
(about 320ml) indicated by “MAX” on the
water tank.
• Close the ller cap of water inlet.
Setting the temperature:
• Stand the iron on its end.
• Set the variable temperature control dial to
the desired temperature setting.
• Insert the plug in the wall socket and stand
the iron upright.
• When the desired temperature is reached the
power indicator light will turn off,and you can
begin ironing.
NOTE: While ironing, the power indicator
light will turn on and off to maintain your
desired temperature setting.
• If you set the temperature control to a lower
setting after ironing at a high temperature,
please allow time for the iron to cool. This is to
prevent scorching your garment.

6
Spray function:
Press the spray button at any time to spray
water on fabrics, as often as required. Make sure
that there is water in the tank. Press the spray
button slowly (for a dense spray) or quickly (for a
vaporized spray).
WARNING: for delicate fabrics, we
recommend moistening the fabric
beforehand using the spray function, or
putting a damp cloth between the iron
and the fabric. To avoid staining, do not
use the spray on silk or synthetic fabrics.
NOTE: Ensure that there is enough water
in the tank to use the spray function.
During rst use, you may have to pump the
spray button several times to start the spraying
function.
Steam ironing:
This function can be used only at higher ironing
temperatures.
• Ensure that there is enough water in the
water tank.
CAUTION! Use the measuring cup supplied
to ll the iron with water through the water
inlet. Do not ll higher than the maximum
level indicated on the water tank to prevent
spillage of water while ironing.
• Set the variable temperature control to the
required position within the ‘steam range’
•• for moderate steam
••• for maximum steam
• Once the required temperature has been
reached, the power indicator light will turn
off.
• Move the steam dial to a position between
minimum and maximum depending on
the quantity of steam required and the
temperature selected. steam should start
coming out from the holes in the soleplate.
The iron is ready to use.
CAUTION! The steam is very hot. DO NOT allow
steam to come in contact with your skin, face
or hands to avoid injury. Never direct steam at
people or animals.
Selecting hot-steam and steam when ironing
vertically:
Press the hot-steam button to generate a
powerful burst of steam that can penetrate
the fabrics and smooth the most difcult and
tough creases. Wait for a few seconds before
pressing again. By pressing the hot-steam button
at intervals you can also iron vertically (curtains,
hung garments, etc.).
WARNING: the hot-steam function can
only be used at high temperatures. Stop
the emission when the power indicator
light comes on, than start ironing again
only after the light has gone off.
Self-Cleaning:
The self-cleaning feature cleans inside the plate,
removing impurities. We recommend using it
every 10-15days. Directions:
• Fill the water tank up to the maximum level
indicated.
• Set the thermostat knob to the maximum
temperature and wait for the power indicator
light to turn off.
• Pull the plug out of the socket and hold the
iron horizontally over the sink.
• Hold the cleanout button setting until all the
boiling water, steam, impurities come out.
• When the soleplate has cooled down, you
can clean it with a damp cloth.
• Do not clean the appliance with abrasive
cleaners or sharp objects, e.g. a hard brush or
knife.

7
Dry ironing:
• To iron without steam, leaving the steam dial
on position“0”.
• Read the washing label instructions on your
clothes to select the required temperature.
• Begin ironing when the power indicator light
turns off.
Anti Drip:
With a bimetal assembled inside the iron,which
can close the steam when the iron soleplate
temperature becomes very low,so water
leakage will never happen with this features.
Auto Shut-Off:
An electronic safety device will automtically
switch the heating element off if the iron has
not been moved more than 30 seconds in a
horizontal position. If in a vertical position, this
will happen after 8 minutes. To indicate that the
heating element has been switched off, the
auto-off pilot light will start blinking.
• When picking up the iron again, the auto-
off pilot light will stop blinking. The power
indicator light will turn on. This indicates that
the iron is heating up again.
• Wait for the power indicator light to turn off.
Then the iron is ready for use.
Relling with Water
• Switch off and disconnect the iron from the
power socket.
• Press the steam dial to “0” position.
• Rell with water, being very mindful of the hot
soleplate if the iron has recently been used.
• Plug the iron into the power socket and wait
until the power indicator light has switched off
before setting the steam dial to the required
steam level.
NOTE: Always disconnect the iron from
the power outlet before lling with water.
Emptying the
Water Tank
• Press the steam dial to “0” position.
• Disconnect the iron from the power socket.
• Hold the iron upside down and gently shake
to remove remaining water.
NOTE: Take care not to scald yourself
during this process.
Storage
Disconnect the plug from the power outlet and
ensure that the iron has cooled and the water
tank is empty before storing in a vertical position.

8
Setting the Temperature - Fabric Guide
Read all garment labels when ironing and ensure the manufacturer’s ironing guidelines are followed.
Always check the garment label for ironing instructions before ironing a garment.
If the ironing instructions are missing, see the table below.
Sort your laundry: Wool with wool. Cotton with cotton, etc. Start ironing the fabrics requiring the lowest
temperature and progress to the higher ones because the iron heats up quicker than it cools down.
NOTE: If the article to be ironed consists of various different fabrics, always select the
temperature required by the most delicate fabric.
Textile chart:
IMPORTANT
Read all garment labels when ironing and ensure the manufacturer’s ironing guidelines are followed.
The manufacturers ironing guidelines are often shown by symbols similar to the below:
FABRIC TEMPERATURE
SETTING
IRONING RECOMMENDATIONS
Acrylic •Dry iron on reverse of fabric.
Acetate •Dry iron on reverse while still damp or use spray to
dampen.
Silk •• Iron on reverse. Use an ironing cloth to prevent
shine marks.
Nylon •• Iron on reverse while still damp or use spray to
dampen.
Polyester •• Iron on reverse while still damp or use spray to
dampen.
Rayon •• Iron on reverse of fabric.
Viscose •• Mainly dry iron. Steam can be used under
manufacturer’s instructions.
Wool •• Steam iron on reverse or use an ironing cloth.
Wool blends •• Steam iron on reverse or use an ironing cloth.
Cotton blends •• Check label and follow manufacturer’s instructions. Use setting for the bre requiring the
lowest setting.
Corduroy ••• Steam iron on reverse or use an ironing cloth.
Cotton ••• Use maximum steam.
Linen •••
Iron on reverse or use an ironing cloth to prevent
shine marks, especially with dark colours. Dry iron
while still damp or use spray to dampen, or use
maximum steam.
Denim ••• Use maximum steam.
• Dry ironing at any setting •• Steam ironing ••• Steam ironing (maximum)

9
Technical Specication
Power supply: ..........................................240V, 50Hz
Power consumption: ......................................2400W
NOTE: As a result of continual improvements,
the design and specications of the product
may differ slightly to the unit illustrated on
the packaging.
Care and Cleaning
• Ensure that the iron is unplugged and has
completely cooled down before cleaning.
• From time to time, clean the exterior with a
damp cloth and wipe dry.
• To prevent scratching of the sole plate, do
not iron over sharp objects (zips, etc.). Do not
place the iron on surfaces that could scratch
the sole plate, such as a metal iron support,
and never use abrasive cleaning agents.
• The rst time the iron is used, a small amount
of smoke may be emitted. This is perfectly
normal and ceases after the appliance has
been in use for a short while.
• Before using the iron for the rst time or if
the iron has not been used for a few weeks,
Hold the cleanout button and follow the
instructions in ‘Self-Cleaning’.
NOTE: Do not leave the iron unattended
when it is connected to the power
socket. If the power cord becomes
damaged, contact the manufacturer or
an authorised service centre for repair.

10
Notes

11
Notes

12
Cat. No. MIR068
November 2020
GSM Retail Group has a policy of continual improvement throughout the product range.
As such the unit contained within may differ slightly from the unit illustrated on the pack.
MADE IN CHINA for GSM Retail Group
Mistral is a registered trademark of GSM Retail Group
GSM Retail Group
Gerard Sourcing & Manufacturing