Mitsubishi Electric MELSEC iQ-F FX5 Service manual

MELSEC iQ-F
FX5 Analog Input Module/Output Module/
Multiple Input Module Function Block Reference

1
CONTENTS
CONTENTS
CHAPTER 1 FUNCTION BLOCK (FB) LIST 2
CHAPTER 2 ANALOG INPUT MODULE, MULTIPLE INPUT MODULE FB 4
2.1 M+Model_RequestSetting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 M+Model_OperateError. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 M+Model_SetLoggingParam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CHAPTER 3 ANALOG OUTPUT MODULE FB 12
3.1 M+FX5-4DA_RequestSetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.2 M+FX5-4DA_OperateError . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.3 M+FX5-4DA_WaveOutputSetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.4 M+FX5-4DA_WaveOutputReqSetting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
INSTRUCTION INDEX 22
REVISIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

21 FUNCTION BLOCK (FB) LIST
1FUNCTION BLOCK (FB) LIST
This chapter lists the FBs for the MELSEC iQ-F series analog input module (FX5-4AD), multiple input module (FX5-8AD),
analog output module (FX5-4DA).
Analog input module, Multiple input module FB
■FX5-4AD
*1 Note that this reference does not describe the FB version information which is displayed such as "_00A" at the end of FB name.
■FX5-8AD
*1 Note that this reference does not describe the FB version information which is displayed such as "_00A" at the end of FB name.
Analog output module FB
■FX5-4DA
*1 Note that this reference does not describe the FB version information which is displayed such as "_00A" at the end of FB name.
Name*1 Description
M+FX5-4AD_RequestSetting Enables the settings of each function.
M+FX5-4AD_OperateError Monitors error codes and resets errors.
M+FX5-4AD_SetLoggingParam Sets up the logging function of a specified channel.
Name*1 Description
M+FX5-8AD_RequestSetting Enables the settings of each function.
M+FX5-8AD_OperateError Monitors error codes and resets errors.
M+FX5-8AD_SetLoggingParam Sets up the logging function of a specified channel.
Name*1 Description
M+FX5-4DA_RequestSetting Enables the settings of each function.
M+FX5-4DA_OperateError Monitors error codes and resets errors.
M+FX5-4DA_WaveOutputSetting Sets the wave output of a specified channel or all channels.
M+FX5-4DA_WaveOutputReqSetting Specifies whether to start, stop, or pause the wave output of a specified channel or all channels.

1 FUNCTION BLOCK (FB) LIST
3
1
MEMO

42 ANALOG INPUT MODULE, MULTIPLE INPUT MODULE FB
2.1 M+Model_RequestSetting
2ANALOG INPUT MODULE, MULTIPLE INPUT
MODULE FB
2.1 M+Model_RequestSetting
Name
The module names of the FB are based on the module used and are as follows.
■FX5-4AD
M+FX5-4AD_RequestSetting
■FX5-8AD
M+FX5-8AD_RequestSetting
Overview
Labels
■Input label
■Output label
Item Description
Overview Enables the settings of each function.
Symbol
No. Variable name Name Data type Range Description
(1) i_bEN Execution command Bit ON, OFF ON: The FB is activated.
OFF: The FB is not activated.
(2) i_stModule Module label Structure The setting range
differs depending on
the module label.
Specifies the module label for the analog input/multiple
input module.
No. Variable name Name Data type Default value Description
(3) o_bENO Execution status Bit OFF ON: The execution command is ON.
OFF: The execution command is OFF.
(4) o_bOK Normal completion Bit OFF The on state indicates that the operation to enable
each setting is complete.
(5) o_bErr Error completion Bit OFF Always OFF
(6) o_uErrId Error code Word [Unsigned] 0 Always 0
(6)
(5)
(4)
M+FX5-4AD_RequestSetting
(3)
(2)
(1)
o_uErrId
o_bErr
o_bOK
o_bENO
UW
B
B
B
DUT
B
:
:
:
:
:
:
i_stModule
i_bEN

2 ANALOG INPUT MODULE, MULTIPLE INPUT MODULE FB
2.1 M+Model_RequestSetting 5
2
FB details
Error code
Item Description
Available device Target module FX5-4AD, FX5-8AD
Target CPU FX5U CPU, FX5UC CPU
Engineering tool GX Works3 Version 1.040S or later
Language Ladder diagram
Number of basic steps 57 steps
The number of FB steps integrated in the program varies depending on the CPU module used, the input/output definition, and
the setting options of GX Works3. For the setting options of GX Works3, refer to GX Works3 Operating Manual.
Processing • Turning on i_bEN (execution command) allows the settings of all channels to be enabled. For what settings are enabled,
refer to MELSEC iQ-F FX5 User's Manual (Analog Control - Intelligent function module).
• This FB continues its execution until the completion of the settings of each function after i_bEN (execution command) turns
on.
FB compilation method Macro type
FB operation Pulsed execution (multiple scan execution type)
Timing chart of I/O signals
Restrictions or precautions • This FB does not include the error recovery processing. Program the error recovery processing separately in accordance
with the required system operation.
• This FB cannot be used in an interrupt program.
• As this FB is executed, the A/D conversion processing stops, and thereafter when o_bOK (normal completion) turns on, the
conversion processing resumes.
• When operating the analog input module and multiple input module, the input range needs to be set according to the device
and system to be connected. Set the GX Works3 module parameters according to the application. Refer to the MELSEC
iQ-F FX5 User's Manual (Analog Control - Intelligent function module) for details on setting the module parameters.
Error code
(hexadecimal)
Description Action
None None None
i_bEN
o_bENO
o_bOK
o_bErr
o_uErrId
0
Operating condition setting request
(Un\G70.b9)
Operating condition setting completed
(Un\G69.b9)

62 ANALOG INPUT MODULE, MULTIPLE INPUT MODULE FB
2.2 M+Model_OperateError
2.2 M+Model_OperateError
Name
The module names of the FB are based on the module used and are as follows.
■FX5-4AD
M+FX5-4AD_OperateError
■FX5-8AD
M+FX5-8AD_OperateError
Overview
Labels
■Input label
■Output label
Item Description
Overview Monitors error codes and resets errors.
Symbol
No. Variable name Name Data type Range Description
(1) i_bEN Execution command Bit ON, OFF ON: The FB is activated.
OFF: The FB is not activated.
(2) i_stModule Module label Structure The setting range
differs depending on
the module label.
Specifies the module label for the analog input/multiple
input module.
(3) i_bErrReset Error reset request Bit ON, OFF Turn on this label to reset errors.
After completion of the error reset, turn off the label.
No. Variable name Name Data type Default value Description
(4) o_bENO Execution status Bit OFF ON: The execution command is ON.
OFF: The execution command is OFF.
(5) o_bOK Normal completion Bit OFF The on state indicates that the error reset is complete.
(6) o_bUnitErr Module error
outbreak flag
Bit OFF The on state indicates that a module error has
occurred.
(7) o_uUnitErrCode Module error code Word [Unsigned] 0 The error code of an error occurred is stored.
(8) o_uUnitAlarmCode Module alarm code Word [Unsigned] 0 The alarm code of an alarm occurred is stored.
(9) o_bErr Error completion Bit OFF Always OFF
(10) o_uErrId Error code Word [Unsigned] 0 Always 0
(7)
(6)
(5)
M+FX5-4AD_OperateError
(4)
(3)
(2)
(1)
o_uUnitErrCode
o_bUnitErr
o_bOK
o_bENO
UW
B
B
B
B
DUT
B
:
:
:
:
:
(8)o_uUnitAlarmCode UW
(9)o_bErr B
(10)o_uErrId UW
:
:
:
:
:
i_bErrReset
i_stModule
i_bEN

2 ANALOG INPUT MODULE, MULTIPLE INPUT MODULE FB
2.2 M+Model_OperateError 7
2
FB details
Error code
Item Description
Available device Target module FX5-4AD, FX5-8AD
Target CPU FX5U CPU, FX5UC CPU
Engineering tool GX Works3 Version 1.040S or later
Language Ladder diagram
Number of basic steps 195 steps
The number of FB steps integrated in the program varies depending on the CPU module used, the input/output definition, and
the setting options of GX Works3. For the setting options of GX Works3, refer to GX Works3 Operating Manual.
Processing • As i_bEN (execution command) turns on, errors in the target module are monitored.
• After i_bEN (execution command) turns on, turning on i_bErrReset (error reset request) during an error allows the error to be
reset.
FB compilation method Macro type
FB operation Arbitrary execution type
Timing chart of I/O signals
Restrictions or precautions • This FB does not include the error recovery processing. Program the error recovery processing separately in accordance
with the required system operation.
• This FB cannot be used in an interrupt program.
• When operating the analog input module and multiple input module, the input range needs to be set according to the device
and system to be connected. Set the GX Works3 module parameters according to the application. Refer to the MELSEC
iQ-F FX5 User's Manual (Analog Control - Intelligent function module) for details on setting the module parameters.
Error code
(hexadecimal)
Description Action
None None None
0
0
0
0
0
Module alarm code
Module alarm code
Module error code
Module error code
i_bErrReset
Error clear request
(Un\G70.b15)
Error flag
(Un\G69.b15)
i_bEN
o_bENO
o_bUnitErr
o_uUnitErrCode
o_uUnitAlarmCode
o_bOK
o_bErr
o_uErrId

82 ANALOG INPUT MODULE, MULTIPLE INPUT MODULE FB
2.3 M+Model_SetLoggingParam
2.3 M+Model_SetLoggingParam
Name
The module names of the FB are based on the module used and are as follows.
■FX5-4AD
M+FX5-4AD_SetLoggingParam
■FX5-8AD
M+FX5-8AD_SetLoggingParam
Overview
Labels
■Input label
Item Description
Overview Sets up the logging function of a specified channel.
Symbol
No. Variable name Name Data type Range Description
(1) i_bEN Execution command Bit ON, OFF ON: The FB is activated.
OFF: The FB is not activated.
(2) i_stModule Module label Structure The setting range
differs depending on
the module label.
Specifies the module label for the analog input/multiple
input module.
(3) i_uCH Target channel Word [Unsigned] ■FX5-4AD
1 to 4
Specifies a channel number.
■FX5-8AD
1 to 8
(4) i_bLogEnable Logging enable/
disable setting
Bit ON, OFF ON: Enables the logging function.
OFF: Disables the logging function.
(5) i_uLogData Logging data setting Word [Unsigned] 0: Digital output
value
1: Digital operation
value
Sets the data to be logged.
(16)
(15)
(14)
M+FX5-4AD_SetLoggingParam
(13)
(3)
(2)
(1)
o_uErrId
o_bErr
o_bOK
o_bENO
UW
B
B
B
UW
DUT
B
:
:
:
:
:
:
:
i_uCH
(4) B : i_bLogEnable
i_stModule
i_bEN
(6)
(5)
UW
UW
:
:
i_uLogCycleVal
i_uLogData
(9)
(8)
(7)
UW
UW
UW
:
:
:
i_uLogTrigCond
(10) UW : i_uLogTrigData
i_uLogPoints
i_uLogCycleUnit
(12)
(11)
UW
W
:
:
i_uUnitType
i_wLogTrigValue