MLILY NUP100 User manual

1-Year Warranty | Parts and Labor
ADJUSTABLE BASE
Owner’s Manual
Installation & Operation

Read important safety informaon before operang this bed:
• Be sure no one is near or under bed when it is moving.
• Do not teach children to operate the remote.
• Store remote where children cannot find it.
• Children and pets can be crushed and killed in moving parts of the bed!
Do not use near explosive gasses or TENT TYPE oxygen therapy equipment.
Do not operate where aerosol (spray) products are being used.
This is not a“hospital”bed and does not meet hospital standards.
To reduce the risk of fire and electric shock:
• Unplug the base before cleaning or servicing.
• Keep power cord away from heat sources
• If cord or plug are damaged, disconnue use.
Manual operaon- If something gets caught in the plaorm
when in use, you can manually raise the platorm up by liing at
both the head and/or foot to relieve pressure and allow for
release.

Safety & Warranty Warnings 1
Parts List 5
Electronics Quick Reference Guide 6
Installaon Guide 8
Remote Control Instrucons 10
Synchronizing Two Bases 11
Troubleshoong 12
CONTENTS

-01-
Safety & Warranty Warnings
To reduce the risk of shock, burns, fire or injury:
Always unplug the base from the electrical outlet before servicing any part of the base. To reduce risk of electric shock, unplug the base before
cleaning. To safely disconnect, ensure the base is in a flat posion with all motors off, and unplug from power source.
Keep the power cord away from heated surfaces. Disconnue use of the bed base and contact a qualified service center if: it has a damaged cord
or plug, is not working properly, or has been dropped into water.
Only use this bed base for its intended use as described in this manual. Do not use accessories/aachments that are not recommended by the
manufacturer.
Close supervision is required when the bed base is used by or near children, convalescents or disabled persons.
Adjustable base must always be used with an appropriate matching size maress.
Outlet Safety:
For opmal safety and operaon, plug bed base into a surge protector (not included).
The bed base should only be plugged directly into a wall outlet or surge protector (recommended). Improper connecon of the equipment can
result in the risk of electrical shock, electrical fire or faulty operaon of this bed base. If the plug does not fit your outlet, contact a qualified
electrician to install a suitable outlet. Unauthorized modificaon or failure to use a wall outlet or surge protector could void the electrical poron
of your warranty.
Aenon: Important Safety Disclaimers SAVE THESE INSTRUCTIONS
Read all instrucons before using your adjustable base.
IMPORTANT!: For your safety, read the owner’s manual carefully and completely before operang this product.
Electric shock may occur if electrical components are not installed or operated according to these guidelines.
To reduce the risk of fire and electric shock:

-02-
Warranty Warning:
Do not open or tamper with control box, motors, or remote (with the excepon of baery compartments). Never drop or insert any object
into any opening. The warranty will be void if the internal workings of these components are tampered with.
In-Home Use and Hospital Disclaimer:
The adjustable bases are designed solely for in-home use. This base was not designed as a hospital bed and is not designed to meet hospital
standards.
Do not use near explosive gasses or TENT TYPE oxygen therapy equipment. Do not operate where
aerosol (spray) products arebeing used.
This is not a “hospital” bed and does not meet hospital standards.
Pets and Small Children:
Children and pets can be crushed or killed if they become entrapped in moving parts of the bed. Before you reposion the base, check to be
sure children and small pets are not near or under the base. Do not teach children to operate the remote. Not to be used in locaons where
children, or people with cognive disabilies are ancipated to be present.
Immediately dispose of all packaging materials as they may pose a smothering risk to small children and pets.

-03-
Safety Features:
Children and pets can be crushed and killed in moving parts of the bed!
• Before you reposion the base, check to be sure children and small pets are not near or under the base
• Do not teach children to operate the remote
• Not to be used in locaons where children, or people with cognive disabilies are ancipated to be present
• Store remote where children cannot find it.
• Immediately dispose of all packaging materials as they may pose a smothering risk to small children and pets.
Manual operaon – If something gets caught in the plaorm, you can manually raise the plaorm by liing at either the head and/or foot to
relieve pressure and allow for release.
Emergency stop – Stop the moon of the plaorm by pressing any buon on the remote control or by pushing the buon on the Baery
Backup located underneath the base.
Power Rangs:
INPUT: AC 100–240V 50/60 HZ 1.6A OUTPUT: DC 29V 1.5A WATTS: 43.5W.

-04-
Weight Limits:
The recommended weight limits for this base are: 650 pounds.
Maximum weight the bed can support per person is 250 pounds with the weight evenly distributed across the head and foot secons. This
product is not designed to support or li this amount of weight in the head or foot secons alone. NOTE: Exceeding the recommended
weight restricons could damage your base and void your warranty. For best performance, you should enter and exit the base while it is in
the flat or fully lowered posion.
FCC Compliance Statement:
FCC Compliance:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons,
may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT!: For your safety, read the owner’s manual carefully and completely before operang this product.
Electric shock may occur if electrical components are not installed or operated according to these guidelines.
Before beginning assembly of the Adjustable Base, please take a moment to familiarize yourself with the parts and locaon of
components.
See the adjacent image for a detailed overview.
A
Bed Leg&Boom Cap(6)
B
Power Supply (1)
& Power Cord (1)
C
Remote Control (1)
D
Retainer Bar (1)
(Two included with K/CK size)
Splier Cable(1)
(included with TXL and CKS size only)
E
Parts List
-05-

Electronics Quick Reference Guide
-06-
Head Motor

Remote
Power Cord
-07-
Power Supply

Two people are required to set up the foundaon.
NOTE: To avoid damage to the foundaon, always open the
carton while the bed is in the flat posion.
Open the shipping box and take out top decking.Cut the
ribbon securing accessory Boxes&maress retainer bar
and put them aside. Carefully take out the bed frame from
packaging and open it .
To Install all legs, thread the bolt of the leg to the nut on the
foundaon frame, and ghten by hand. DO NOT OVERTIGHTEN.
Installation Guide
-08-
1.
2.
Uncoil the input power cord (connected to the head motor on the
underside of the base) and plug it into the power supply.
Uncoil the remote and connect it to head motor.
3.

-09-
5. Carefully flip the foundaon over onto its legs.
Important: Two people are required to move the
foundaon. Do not drag across the floor. Do not rest frame
on its side; excessive pressure may damage the legs.
6. Locate the maress retainer bar brackets.
Slide the le side of the maress retainer bar into the
bracket. Pull the retainer bar to the opposite bracket and
secure the right side.
Head
Leg Posions
Foot
A

Remote Control Instructions
-10-
Head Up
Head Down

-11-
STEP 1
Ensure both bases (A & B) are plugged into a power source
and both in the flat posion.
TO SYNC REMOTE TO TWO BASES:
FOR TXL OR CKS BASES ONLY
OVERVIEW
Two TXL or CKS bases may be placed next to each other to form a Split or a Split Cal King. Both sides can be operated independently with
their own remotes or, if desired, a single remote can be used with both bases. Using a single remote for both bases will result in the
bases moving jointly.
Synchronizing Two Bases
Base A Base B
STEP 2
Using the splier cable (included with split bases only) plug
both cables into each base (A & B). Finish by aaching the
last cord to one remote. The both bases should now be
controlled by the one remote.

-12-
Troubleshooting
In the event that the power foundaon fails to operate, assess the symptoms and possible soluons provided in the chart below.
SYMPTOMS SOLUTIONS
Remote control illuminates and appears to be
operable, but will not acvate bed.
No features of the power foundaon will
acvate.
There is no sound at all aer the adjustable
base is re-plugged, and the remote control
can't control it, but the power supply is on.
The remote will not operate the base.
Verify that the power cord is plugged into a working, grounded electrical outlet. Test the
outlet by plugging in another working appliance.
The plug at the motor end may be loose. Check all the plugs again.
Check to ensure that the remote control is secured completely and that the power cord is
plugged into the wall outlet.
Ensure that all wired connecons are secured below the bed base.
Unplug the power cord, wait 30 seconds andplug back to reset electronic components.
The surge protecon device or the electrical outlet may be defecve. Test the outlet by
plugging in another working appliance.
Verify that the connector on the wired remote control is securely aached to the motors.

-13-
SYMPTOMS SOLUTIONS
Head li funcon has minor interference
during operaon.
Head secon will elevate but will not return
to the horizontal (flat) posion.
Make sure that you are following the duty cycle of the motor (do not operate more than
two minutes over a 18-minute period, or approximately 10% duty cycle).
Press the li buons squarely and accurately.
Wireless remote control may be experiencing common Radio Frequency Interference
from other radio transming devices. Wait several seconds, and then try pressing
appropriate buon again, See FCC Compliance Statement on page 4 of this guide.
Bed mechanism may be obstructed. Elevate bed and check for obstrucon. Remove
obstrucon.
Head secon may be too close to the wall.
Headboard may be too close to the edge of the maress. Verify that there is enough
distance between the headboard brackets andmaress. Adjust if required.
A clicking noise is heard under the bed when
raising or lowering. This is normal. The li motor relays “click” when they are engaged. No acon is required.