Modern Forms 419-Outdoor Wall Sconce Series User manual

1
INSTALLATION INSTRUCTIONS
419-Outdoor Wall Sconce
WS-W41912/WS-W41918
HARDWARE
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019
JANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Wire Connector
Qty:
3 pcs+1 Extra
Back Plate Screw
Qty: 1 Extra
Rubber Gasket
Qty:
1 Extra
ABC
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT
BREAKER BEFORE BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC)
and local regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the
supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not
designated for use with this product by Modern Forms could result in personal injury or property damage, and will void
the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that
customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et
également aux règlements locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour
être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms.
Remplacer des pièces ou accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages
corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé
ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire.
Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du
luminaire une fois toutes les deux semaines avec un chiffon humide.

2
INSTALLATION INSTRUCTIONS
419-Outdoor Wall Sconce
WS-W41912/WS-W41918
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 3 Wiring
Fig. 1 Fig. 2
Fig. 4
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2019
JANUARY, 2017
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and remove existing
fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on
a clear area. Be careful not to lose any small parts necessary
for installation.
MOUNTING THE FIXTURE (Fig. 1)
3.
4.
Remove the back plate screw (B) and back plate from the
fixture.
Secure the back plate to the junction box using the screws
provided with the junction box.
NOTE: The side of the back plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 3)
5. Connect the fixture’s wires to house wires as shown (Fig.3). Make sure that all wire connectors (A) are secured. If
your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, tuck the
fixture’s ground wire directly to the fixture. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
6. Secure the fixture to the mounting back plate using the back plate screw (B) and rubber gasket (C).
7. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone
sealant) to outline the outside of fixture back plate where it meets the wall. Leave a space at the bottom to allow
moisture to escape (Fig.4).
Junction Box
Wire Connector
Junction Box Screw
Fixture
A
Back Plate Screw
B
Rubber Gasket
C
Back Plate
Junction Box
Caulking
2 3/8"
1 3/8"
4 5/8"
4 1/2"
Back Plate Dimensions