Modern Forms 540-Outdoor Wall Sconce Series User manual

1
INSTALLATION INSTRUCTIONS
540-Outdoor Wall Sconce
WS-W54016/WS-W54020/WS-W54025
HARDWARE
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov.2019
CAUTION:To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
•Read all instructions before installing.
•System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
•When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
•Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions.This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms.Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture.We recommend that customers in coastal
areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
•Lisez toutes les instructions avant l’installation.
•Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
•Lors de la manipulation du luminaire, n’appuyez pas sur les LED.Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie.Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chiffon humide.
Wire Connector
Qty: 3pcs+1 Extra
A
Mounting Screw
Qty:1 Extra
BE
Plastic Anchor
Qty: 2pcs+1 Extra
Rubber Gasket
Qty:1 Extra
C
Wood Screw
Qty: 2pcs+1 Extra
D

2
INSTALLATION INSTRUCTIONS
540-Outdoor Wall Sconce
WS-W54016/WS-W54020/WS-W54025
FIG. 1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov.2019
modernforms.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and
remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out
all the parts on a clear area. Be careful not to
lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and rubber
gasket (C) from the mounting backplate.
4. Secure the mounting back plate to the junction
box using standard junction box screws that
comes with the junction box.(For model
WS-W54016 and WS-W42020, drill holes in the
wall aligned with the key holes in the mounting
backplate, insert the plastic anchors (E),fasten
the mounting backplate to the wall using wood
screw (D).
Note: (i) using any other non-original-manufacturer provided junction box screw may result in safty issue;
(ii) The side of the mounting plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
5. Connect the fixture’s wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your outlet box has
a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the back
plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
COMPLETING THE INSTALLATION
6. Secure the fixture to the mounting back plate using the mounting screw (B)
and rubber gasket (C).
7. Insert the glass into the lamp cap, then push the glass up to the spring until
the glass is fully positioned within the fixture. Release the glass gently to
prevent any external damages from all the tensional spring and make slight
adjustment to allow the glass properly aligned with the fixture body.
8. To prevent moisture from entering the outlet box and causing a short, use
clear caulking (i.e. indoor/outdoor silicone sealant) to outline the outside
of fixture back plate where it meets the wall. Leave a space at the bottom to
allow moisture to escape Fig.3
Limit
Block
Tension
Springs
Clear Hammered
Seedy Glass
(RPL-GLA-54016)
(RPL-GLA-54020)
(RPL-GLA-54025)
Rubber Gasket
C
Mounting Screw
B
Wood
Screw
Junction Box Screw
Mounting Backplate
Plastic Anchor
E
Junction Box
Wire Connector
A
D
Black Wire
White
Wire
Ground Wire
Lamp Cap
Push
Release
Mounting Plate Dimensions
WS-W54016 4 1/8"
WS-W54020 4 1/4"
WS-W54025 4 1/2"
WS-W540167 5/8"
WS-W54020 9 1/2"
WS-W54025 11 7/8"
1 3/4"
1 3/8"
Caulking
Junction Box
FIG.3 Sealing