Operation Instruction
Key button
LED Screen
1. Long press the up/down buttons to adjust the height of the desk; The screen will show “bot” when the desktop runs to its lowest point;
and it will show “top” when the desktop runs to its highest point.
2. key button: 1,2,3,4 are the four height memory buttons, long press the button about 3s can record the current height;
3. Press the 3 and 4 buttons at the same time, the RST reset indication will appear. Continue to press the "▼" down button until the lifting table
lowers to the lowest position and rebounds to rise to a stop. The display shows the lowest height "bot", release "▼" down button, the reset is
over and the table can be used normally.
4. The desk has two USB, one type-C ports, they can supply power to other electronics. Every channel can maximum output DC 5V/2.4A
power when the desktop is stationary and will stop output when the desktop is running. It will resume output after 5s of inactivity.
5. Short press the “LOCK” button to achieve the child lock function, so as to avoid accidentally touch and guarantee the safety of children;
The child lock button is switchable, screen will show “Loc” when the desk is locked.
6. Long press the up and down button to switch the sensitivity level. When the screen shows “A-0”, it means the anti-collision function is off,
“A-1” means the anti-collision sensitivity is in level 1, “A-2” means the anti-collision sensitivity is in level 2, “A-3” means the anti-collision
sensitivity is in level 3, level 3 means the highest sensitivity.
●Troubleshooting:
a. Reset: When the LED shows" " , press “▼” button until the desk reaches its lowest height and rebounds to stop, it means the reset
has been finished.
b. When it does't work and the LED shows "E01" or "E02", please retry 18 mins later.
c. If the “▼” button does't work, please check the cable connection and then cut off thepower for at least 10 seconds. Reconnect to the
power and press “▼” button to start the reset process when it shows the " ".
d. If all these above process are inefficient, plz contact our customer service.
Troubleshooting Guide Attention
1. Power supply: AC100V-240V,50/60Hz
2. Service Environment: 0-40℃
3. Unplug the power plug before cleaning, wipe the dust on surface with slight wet
dishcloth when cleaning, be careful not to let the drops into the internal parts, not loose
the connector.
4. The electric box contains electronic components, metals, plastics, wires etc., so
dispose of it in accordance with each country's environmental legislation, not the
general household waste.
5. Check carefully to ensure correct and complete assembly before using.
6. Be familiar with all functions and program settings of the product before first use.
7. Children are forbidden to play on the desk as the behavior is unpredictable.
Manufacturer is not responsible for loss, injury, or damage due to those improper
action.
8. Slight noise caused by the V-ribbed belt or brake system due to structure will not
have any effect on the use of the equipment.
9. Corrosive or abrasive materials are forbidden to clean the equipment. Must ensure
that the cleaner used will not pollute the environment.
10. This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play
with the appliance.
11. Cleaning and user maintenance shall not be made by children without supervision.
12. If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or a similarly qualified person in order to avoid a hazard.
13. Please make sure there is no hazard sources in your operating environment. e.g.,
do not litter the tools around. Always be careful to treat the packaging materials in order
to avoid any possible danger, e.g. plastic bag may lead to choking hazard to children.
14. Keep the original package of the equipment if necessary in case of the future use in
transportation.
Waste disposal This marking indicates that this product should
not be disposed with other household wastes.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable
reuse of material resources. To return your used
device, please use the return and collection
systems or contact the retailer where the
product was purchased. They can take this
product for environmental safe recycling.
lease try the tips below to help resolve
simple performance issues. Please contact
Modern Office with any questions.
lssue Solution
Unplug from power source. Then,
disconnect all cables from control
box. Let rest for 1 minute. Then
reconnect cables and plug back
into power source.
Desk is not responding
or moving
when keypad is touched
Desk raises at slow speed Make sure total weight load is
not exceeding 110 lbs.
One leg cable is probably slightly
disconnected. Unplug/reconnect
Desk needs to rest for
18 minutes to reset.
Desk needs to be reset. Press the
DOWN button until desk goes to
lowest height/rebounds to stop.
Collision sensor is being activated.
Make sure path is clear.
Adjust Collision Sensitivity if desired.
Only one side raises/lowers
Desk stops lowering/raising
and goes opposite direction.
Desk is overworked (moving
longer than 2 minutes)
Display shows “RST”
(sometimes looks like “ ”)
