Moen ACC1401 User manual

ACC1413
ACC1411 ACC1412
ACC1406 ACC1407 Series ACC1408
浴室配件
Bathroom Accessories
浴室配件
ACC1401
ACC1402
ACC1403
ACC1404
ACC1405
INS11959B - 8/10
产品售后保修条款
摩恩产品是在高质量标准及生产工艺下制造的，摩
恩承诺为消费者购买的洁具产品提供有期限免费保
修及终身维修服务。
浴室配件免费保修期为1年，均自消费者购买日（
以摩恩产品分销商开具的发票或收据上载明日期为
准）起计。
免费保修范围为产品及产品配件由于材质及工艺原
因而造成的故障或损坏。免费保修期内，我们将无
偿为您提供修理服务及更换发生故障的产品或产品
配件。摩恩的售后服务责任仅限于对故障产品的修
理，而不延及您因产品故障而发生的其他损失，法
律另有规定的除外。
您需了解：产品外观碰伤、刻划痕迹，以及滥用及
不正当保养所导致的故障或损坏，均不属于免费保
修范围。即使在免费保修期内，属下列
（1）-（5）情况之一的，需酌情收取修理费用：
1. 不能出示相符的保修卡和有效购买凭证情况的，
2. 未按使用说明书告知的使用方法和注意事项造成
的故障，
3.自行拆卸、维修、改装所造成的故障和损坏，
4.由于不可抗力等外部原因引起的故障和损坏，
5.由于运输、搬卸、挤压等造成的损坏。
4.整组挂件安装，用内六角板手将底座锁紧。
1. 在安装位置打1组ø6深30mm的孔。

Bathroom Accessories
合格证
产品名称
检验员
生产日期
Compliance Certification
Inspector
ProductName
Date of Production
浴室配件
Bathroom Accessories
ACC1413
ACC1411 ACC1412
ACC1406 ACC1407 Series ACC1408
ACC1401
ACC1402
ACC1403
ACC1404 ACC1405
INS11959B - 8/10
MOEN LIMITED WARRANTY
We offer limited warranty and lifetime maintenance for
Moen products, which are all manufactured with high
standards of workmanship.
The period of warranty shall start from the date of
purchase of the product (according to the invoice or
receipt issued by Moen distributors) and shall cover a
period of the following: the warranty period for
Bathroom Accessory is 1 year.
This warranty is your coverage against material and
workmanship malfunction or defects in Moen products
or components. During the warranty period, we offer free
maintenance and changing of malfunctioned products or
product components. Moen’s after sales service liability
is limited to the maintenance of faulty items and does not
cover your other losses caused by product malfunction,
except for otherwise stipulated by law.
Cosmetic damages (scratches, dents, etc.) and
malfunction or defects caused by abuse or improper
maintenance is not covered by this warranty.
Although the warranty period remains valid, in case of
the following conditions (1) - (5), the maintenance cost
(material cost and labor cost) shall still be charged as
the case may be:
1. Corresponding warranty card and valid invoice cannot
be presented;
2. Faults were caused by the incompliance with the
instructions and precautions provided in the user’s
manual;
2. Put the two expansion sleeves into the
hole, the end face is flush with the wall.
3. Use self-tapping screws to lock the
base to the
installation position.
4. Install the whole set Accessory and use
Hex
Installation Guide:
1.Drill a group of φ6, deep 30mm holes
in intended
position.