Monogram ZIP360NH User manual

Product Specication Revised 5/15
Monogram®36" Built-In French-door Bottom-freezer
SECTION 1
ZIP360NH
SECTION 2
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
FLUSH INSET INSTALLATION
STANDARD INSTALLATION

OVERALL DIMENSIONS
AFTER PANEL INSTALL
Product Specication Revised 5/15
Monogram®36" Built-In French-door Bottom-freezer
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
SPECIFICATIONS
Overall Width 38" (96.5 cm)
Overall Height 84 1/2" (214.6 cm)
Overall Depth 25 7/8" (49.5 cm)
Door Clearance 19 1/2" (49.5 cm)
Cutout Width 39" (99.1 cm)
Cutout Height 85" (215.9 cm)
Cutout Depth 26 3/16" (66.5 cm)
Electrical Requirements 115 V AC, 60 Hz
20 amp circuit
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 663 lb (300.7 kg)
ZIP360NH
38" (96.5)
10 13/16"
(27.5)
7/16"
(1.1)
20 5/8" (52.4)
25 7/8" (65.7)
*84 1/2"
(214.6)
*73 5/16"
(186.2)
*4"
(10.2) SIDE VIEWFRONT VIEW
*83 1/2"
(212.1)
35" (89.0)
Case width
ZIP360NH
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
**8"
(20.3)
19 1/2"
(49.5)
TOP VIEW
*115° Door swing
**8"
(20.3)
*26 3/8"
(70.0)
7/16"
(1.1)
†Doors can be adjusted to
90° door swing
†Allow 4" (10.2) min
distance to adjacent
wall from cutout
†Allow 4" (10.2) min
distance to adjacent
wall from cutout
FLUSH INSET INSTALLATION

Product Specication Revised 3/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area
ZIP360NH
FLUSH INSTALLATION
ZIP360NH
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
6"
(15.2)
4 1/16"
(11.0)
7"
(17.8)
7"
(17.8)
10"
(25.4)
3/4" (1.9)
Width of side cleats
5 1/4" (13.3)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
FRONT VIEWSIDE VIEW
TOP VIEW
WATER
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
3/4" Panel
Case
Door
85"
(215.9) 85" (215.9)
A
FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET INSTALLATION
ANTI-TIP BRACKET
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• The bolts will be used to attach bracket
to wall in 4 locations. Two of the
locations must penetrate the center
of the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure
81 1/2" from oor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within the
center 32.5" of installation opening to
ensure 2 wall studs are penetrated.
• The bracket will be centered left to
right in opening with bottom of
bracket on the horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings
in back of the unit. The unit will be
secured to the bracket using supplied
“L” bolts.
See Installation Instructions for
detailed instructions.
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
B

Product Specication Revised 5/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
3/4" RAISED FRESH FOOD DOOR PANELS ROUTING
FLUSH INSET 3/4" PANEL DIMENSIONS
ZIP360NH
Grille Panel
Fresh
Food
Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
E E
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed 1/2" or 3/4" custom door, drawer
and grille panels are required. For 3/4"
raised panels, routing is required. The router
depth is 1/4" all the way around the panel’s
backs. Additional panel width reductions
are required per the diagrams shown. This
will create “picture frame’ routing allowing
the panels to slide into the attached door,
drawer and grille trims.
Maximum total panel weight:
• Fresh food door panels – 30 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
Door Handles
Door handles not included. Custom handles
supplied by your cabinet maker may be used.
ZKHFD2H: European tubular stainless steel
handles designed to t 3/4" panels. Kit
includes three handles.
FLUSH INSET INSTALLATION
A B C D E
38" 10 13/16" 46 7/16" 22 3/8" 18 3/4"
PANEL DIMENSIONS
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
3/4"
11/32"
1/4"
3/16"
1/4" 7/16"
DETAIL TOP
DETAIL BOTTOM
HINGE SIDE HANDLE SIDE
2 1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
3/16"
WARNING:
Door Trim Pinch Point Hazard
Improper installation can lead to a
nger pinch point hazard between the
side door trim and the cabinets when
operating the door, especially with
children. To minimize this risk you must
follow the installation instructions for
cabinet dimensions, trim assembly and
door stop angle.

Product Specication Revised 5/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
3/4" RAISED GRILLE PANEL ROUTING
3/4" RAISED FREEZER DRAWER PANEL ROUTING
ZIP360NH
Trimmed refrigerators are designed to be
customized with decorative panels. Field-
installed 1/2" or 3/4" custom door, drawer
and grille panels are required. For 3/4"
raised panels, routing is required. The router
depth is 1/4" all the way around the panel’s
backs. Additional panel width reductions
are required per the diagrams shown. This
will create “picture frame’ routing allowing
the panels to slide into the attached door,
drawer and grille trims.
Maximum total panel weight:
• Fresh food door panels – 30 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
Door Handles
Door handles not included. Custom handles
supplied by your cabinet maker may be used.
ZKHFD2H: European tubular stainless steel
handles designed to t 3/4" panels. Kit
includes three handles.
FLUSH INSET INSTALLATION
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
3/4"
11/32"
1/4"
1/4"
1/4" 1/2"
DETAIL TOP
DETAIL BOTTOM
1/4"
DETAIL TOP
DETAIL BOTTOM
ROUTER DEPTH 1/4"
1 11/16"
2 1/16" 2 1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
2 1/16" 2 1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE

FLUSH INSTALLATION
ZIP360NH
39" (99.1) Flush inset width
37 1/2" (95.3)
Width between cleats
6"
(15.2)
4 1/16"
(11.0)
7"
(17.8)
7"
(17.8)
10"
(25.4)
3/4" (1.9)
Width of side cleats
5 3/8" (13.7)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 13/16" (52.9)
Depth to cleat
3 1/2"
(8.9)
75 1/2"
(191.8 )
From floor
to bottom
of electrical
area
ELEC.
FRONT VIEWSIDE VIEW
TOP VIEW
WATER
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
1/2" Panel
Case
Door
85"
(215.9) 85" (215.9)
Product Specication Revised 3/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area
ZIP360NH
A
B
FLUSH INSET INSTALLATION 1/2" PANELS FLUSH INSET INSTALLATION
ANTI-TIP BRACKET
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• The bolts will be used to attach bracket
to wall in 4 locations. Two of the
locations must penetrate the center
of the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure
81 1/2" from oor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within the
center 32.5" of installation opening to
ensure 2 wall studs are penetrated.
• The bracket will be centered left to
right in opening with bottom of
bracket on the horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings
in back of the unit. The unit will be
secured to the bracket using supplied
“L” bolts.
See Installation Instructions for
detailed instructions.
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET

Product Specication Revised 5/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
FLUSH INSET1/2" PANEL DIMENSIONS
ZIP360NH
Grille Panel
Fresh
Food
Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
E E
The 1/2" overlay panel must be secured to
a .10" spacer panel and a 1/4" thick backer
panel, which slides into the trim.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer
panel, left to right and top to bottom. Secure
the panels with glue.
• Refer to the chart for locating the backer
panel to the overlay panel. Secure the
overlay panel to the backer panel with glue
and screws. Screws must be countersunk
into the backer panel.
Maximum total panel weight:
• Fresh food door panel – 30 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs.
FLUSH INSET INSTALLATION
PANEL DIMENSIONS
A B C D E
1/4" Backer Panel 33 7/8" 8 7/8" 46 1/16 21 7/8" 16 1/2"
.10" Space Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2" 15"
1/2" Overlay Panel 38" 10 13/16" 46 7/16" 22 3/8" 18 3/4"
A B C D
Fresh Food Door Panels 2 1/16" 3/16" 3/16" 3/16"
Freezer Drawer Panel 2 1/16" 2 1/16" 1/4" 1/4"
Grille Panel 2 1/16" 2 1/16" 1 11/16" 1/4"
PANEL DIMENSIONS
1/4" BACKER ASSEMBLY DIMENSIONS
C
AB
C
DD
BA
Hinge Side
Backer with
Overlay Panel
Assembly
Fresh Food
Back
Fresh Food
Back
1/2"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
C
D
AB
Freezer Drawer
C
D
A B
Grille Back
WARNING:
Door Trim Pinch Point Hazard
Improper installation can lead to a
nger pinch point hazard between the
side door trim and the cabinets when
operating the door, especially with
children. To minimize this risk you must
follow the installation instructions for
cabinet dimensions, trim assembly and
door stop angle.

OVERALL DIMENSIONS
AFTER PANEL INSTALL
Product Specication Revised 5/15
Monogram®36" Built-In French-door Bottom-freezer
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
*Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
ZIP360NH
STANDARD INSTALLATION
SPECIFICATIONS
Overall Width 36" (91.4 cm)
Overall Height 84" (213.4 cm)
Overall Depth 25 3/8" (64.5 cm)
Door Clearance 18 3/16" (46.2 cm)
Cutout Width 35 1/2" (90.2 cm)
Cutout Height 84" (213.4 cm)
Cutout Depth 24" (61 cm)
Electrical Requirements 115 V AC, 60 Hz
20 amp circuit
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 614 lb
*84"
(213.4)
FRONT VIEW
*73 1/4"
(186.1)
*26 7/16"
(67.1)
1/2"
(1.3)
9/16"
(1.4)
9 7/8"
(25.1)
46 5/16"
(117.7)
36" (91.4)
25 3/8" (64.5)
23 13/16" (60.5)
*4 1/8"
(10.5) SIDE VIEW
1 5/8"
(4.1)
*83 1/2"
(212.1)
**11 13/16"
(30.0)
**11 13/16"
(30.0)
18 3/16"
(46.2)
TOP VIEW
(SHOWING DOOR SWING)
35" (89.0)
Case width
ZIP360NZ
**130° Door swing
†Doors can be adjusted to
90° door swing
†Allow 4" (10.2) min
distance to adjacent
wall from cutout
†Allow 4" (10.2) min
distance to adjacent
wall from cutout

Product Specication Revised 3/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
STANDARD INSTALLATION 3/4" PANELS
AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area
ZIP360NH
STANDARD INSTALLATION
STANDARD_INSTALLATION
ZIP360NH
24" (61)
1 9/16"
(3.97)
3 1/8"
(7.93) 35 1/2" (90.2)
2 5/16"
(5.874)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*84"
(213.4)
*Trim will overlap
additional 7/16"
6"
(15.24)
10"
(25.4)
ELEC.
SIDE VIEW FRONT VIEW
TOP VIEW
5"
(12.7)
5"
(12.7)
WATERW
A
B
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
The information below applies to all
installation constructions:
• A wall bracket, bolts and toggles will
be supplied with the unit.
• The bolts will be used to attach
bracket to wall in 4 locations. Two
of the locations must penetrate the
center of the wall studs.
• The toggles are used for stability in
drywall and when metal studs are
encountered. Lag bolts are used in
wood studs.
• In installation opening, measure
81 1/2" from oor and draw a
horizontal line.
• Locate and mark the wall studs on
horizontal line. Verify at least two
studs have their centerlines within the
center 32.5" of installation opening to
ensure 2 wall studs are penetrated.
• The bracket will be centered left
to right in opening with bottom of
bracket on the horizontal line.
• When unit is placed in opening, the
bracket tabs will align with openings
in back of the unit. The unit will be
secured to the bracket using supplied
“L” bolts.
See Installation Instructions for
detailed instructions.
SIDE VIEW INSTALLED
WITH ANTI-TIP BRACKET
81 1/2"
(207.0)
Use two
additional hole
locations at end
of brackets
Wall
Studs
Bracket
mounted
into vertical
wall studs
centered
within the
cutout
C
Ensure holes
selected are
centered on
the studs
L
FRONT VIEW OF CUTOUT
WITH ANTI-TIP BRACKET
ANTI-TIP BRACKET

Grille Panel
Fresh
Food
Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
E E
Door
1/4" Framed Panel
Supplied Handles
Trim
A B C D E
1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2"
PANEL ASSEMBLY CROSS SECTION
PANEL DIMENSIONS
Product Specication Revised 3/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
Trimmed refrigerators are designed to be
customized with decorative panels Field-
installed custom door and grille panels
are required.
1/4" Framed Panels:
For 1/4" thick custom panels ordered from
your cabinet maker. The decorative panels
slide into this trim.
Maximum total panel weight:
• Fresh food door panel – 30 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
Door Handles:
The supplied handles accommodate both
framed or overlay panels. Custom handles
of your choice, supplied by your cabinet
maker, can also be installed.
.
STANDARD 1/4" FRAMED PANEL DIMENSIONS
ZIP360NH
STANDARD INSTALLATION

Product Specication Revised 3/15
Monogram®36" Built-In French-door Bottom-freezer
NOTES
Trimmed refrigerators are designed to be
customized with decorative panels Field-
installed custom door and grille panels
are required.
ZIP360NH
STANDARD INSTALLATION
Grille Panel
Fresh
Food
Panel
Fresh
Food
Panel
Freezer Drawer Panel
A
B
C
D
E E
A B C D E
1/4" Framed Panel 33 7/8" 8 7/8" 46 1/16" 21 7/8" 16 1/2"
.10" Framed Panel 32 1/2" 7 5/8" 44 11/16" 20 1/2" 15"
3/4" Overlay Panel 34 1/8" 9" 46 5/16" 22" 16 5/8"
Door
1/4" Backer Panel
.10" Spacer Panel
Supplied Handles
Trim
3/4" Overlay Panel
PANEL ASSEMBLY CROSS SECTION
PANEL DIMENSIONS
.25" + .10" + .75" = 1.10" Total Panel Thickness
STANDARD 3/4" OVERLAY PANEL DIMENSIONS
3/4" Overlay Panels:
For your 3/4" thick custom panels
ordered from your cabinet maker the
overlay panel must be secured to a
1/4"-thick backer panel which slides
into the trim. A spacer panel 0.10" thick
must be placed between the overlay
and backer panels.
Center each panel over the other.
Assemble the panels with glue and
screws. Screws must be countersunk
into the backer panel.
NOTE: Left-to-right oset is not always
equal to top-to-bottom oset.
Maximum total panel weight:
• Fresh food door panel – 30 lbs.
• Freezer drawer panel – 28 lbs.
• Grille panel – 11 lbs
Door Handles:
The supplied handles accommodate
both framed or overlay panels. Custom
handles of your choice, supplied by your
cabinet maker, can also be installed.
ZKHFD2H: European tubular stainless steel
handles designed to t 3/4" panels. Kit
includes three handles.
A B C D
Fresh Food Door Panels 1/8" 01/8" 1/8"
Freezer Drawer Panel 1/8" 1/8" 1/16" 1/16"
Grille Panel 1/8" 1/8" 1/16" 1/16"
PANEL DIMENSIONS
1/4" BACKER ASSEMBLY DIMENSIONS
C
AB
C
DD
BA
Hinge Side
Backer with
Overlay Panel
Assembly
Fresh Food
Back
Fresh Food
Back
1/2"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
C
D
AB
Freezer Drawer
C
D
A B
Grille Back

FEATURES AND BENEFITS
Product Specication Revised 5/15
Monogram®36" Built-In French-door Bottom-freezer
French-door design gives your wide-open access
to every fresh food shelf and bin.
Finely crafted glass-front metal door bins with
riveted metal accents oer easy access
to beverages and quick-grab items.
LED lighting positioned throughout the interior
and under fresh food drawers spotlights food
inside the refrigerator and in the freezer.
Upfront electronic controls with digital readout
oer a range of precise temperature settings, all
within easy reach.
Large full-extension freezer drawer has storage
bins that slide out independently of one another
for easy loading and unloading. An automatic
icemaker keeps plenty of ltered ice on hand.
Precision glass-front produce and deli drawers
feature full-extension, soft-close slides.
Aluminum trimmed glass shelves allow
convenient access to contents in the fresh-food
compartment.
ZIPS360NH