Monogram Monogram ZFSB25DSS User manual

Installation
Instructions
Free-Standing Side-by-Side
Stainless Steel Refrigerator
ZFSB25DSS
ZFSB26DSS
Monogram°

Safet information
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT- Sa,e_hesei.st,.rtio,,s
for local inspector's use.
.IMPORTANT- Obser,eaU>,er,_i._
codes and ordinances.
•Note to Installer -Be sm'e to leave these
instructions with tile Consmner.
• Note to Consumer - KeeI)these instructions with
)orn" O_ner's Mmmal for future reference.
WARNING:
This appliance must be I_r°I_erlv ,gr(mnded. See
"(;rounding tile Refrigerator," page 4.
AVERTISSEMENT :
Cet appareil dolt _tre correctement rnis a la terre.
(krnsulter <_Mise a la terre du r(_frig(_rateur ' lxige, 4.
If _ou received a d'mv_,,ed refrigerator, _ou should
immediatel} contact }our dealer or bnilder.
Skill Level - Installation of this reii'igerator requires
basic mechanical, carpentry and plum/)ing skills.
Proper installation is tlle responsibilit} of tile installer.
Product fhilure due to improper installation is not
covered under tile GE Appliance _v\_rranty. See tile
Owner's Manual fl)r warranty inflmnation.
CAUTION'.
Due to the _eight and size ot this refrigerator, and to
reduce tile risk of personal iqiur ) or damage to tile
product - T_'_70 PEOPI,E ARE REQUIRED FOR
PROPER ]NSTALIATION.
PRUDENCE ."
_ cause du poids et de la taille de ce r(4irig(4ratem" et
porn" rg_duire le risque de blessure et de dornrnages,
IL EkUT DEUX PERSONNES POUR EMRE
' SL IN, TALLATION (:ORRECTEMENT.
WARNING:
* Use this appliance onE' fl)r its intended pro'pose.
* Immediately repair or replace electric service cords
that become f/"ayed or damaged.
* Unplug tile ret/"igemtor betore cleaning or making
repail_.
* Repairs should be made by a qualified service
technician.
AVERTISSEMENT :
* ]lne/hut utiliser (et appareil que p(rnr l'utilisation
appropri_e.
* Rg_parer ou rernplacer irnmg_diaternent tout cordon
61ectfique efliloch6 ou endommag6.
* 11flair dObrancher le r_ii'ig&'ateur avant le
netto)_lge ou route inte_xention.
* Les r(4pamtions doivent &tre fhites par un technicien
qualifi&
For Monogram local service in your area, call
1.800.444.1845.
For Monogram service in Canada, call
1.888.880.3030
For Monogram Parts and Accessories, call
1.800.626.2002.
www. monogram.corn
CONTENTS
Planning Information
Product Dimensions and Clearances .............................. 3
The Installation Space ...................................................... 3
Installation Instructions
Tools, Hardware, Materials .............................................. 4
(;rounding tile Refi'igerator ............................................ 4
Step 1, Move Refl'igerator Indoors (ZFSB25) ................ 5
Step 1A, Move Reti'igerator Indoors (ZFSB26) .............. 6
Step 2, Install _'\_lter Line ................................................ 7
Step 2A, RO _%ter Line .................................................. 8
Step 3, Connect *v_tter Supply ........................................ 8
Step 4, Connect Power .................................................... 8
Step 5, Move Retfigerator Into Position ........................ 8
Step 6, I,evel Refl'igerator ................................................ 9
Step 7, I,evel Doors .......................................................... 9
Step 8, Start Icemaker .................................................... 10
Step 9, Temperature Controls ........................................ l0
Step 10, Install Toekick .................................................. l0
2

Plannin information
PRODUCT DIMENSIONS
AND CLEARANCES
72-1/4"
30_1/2"/_._ /
Including Including
Handles Handles
ZFSB26 ZFSB25
This Mono,,T'ml_, free-standing, refrigerator, requires
tile following clearances for proper air circulation,
plumbing and electrical connections.
Air Circulation Clearances:
* 1/8" on each side
*1" at the top
*1" at the back (1-1/2" for Z]_. g2a)
Installation in a corner:
*Allow 4" clearance on each side to an ac!iacent wall
for a 90 ° opening and access to drinkers.
ZFSB25 and ZFSB26
14q/4"
. ' • 160°DoorSwing 19"_
ZFSB25 ZFSB26
90°D S ' T_ "!8"
* On the freezer side, allow 14-1/4" rain. clearance
flw removal of ice bill.
*On the fl'esh fl)od side, allow 19" mill. clearance
to wall flw removal of drawers.
THE INSTALLATION SPACE
The ol_ening, width must be .36-1/4".
73"rain.
36-1/2"_
Electrical
Area
WallView
Water And Electrical Locations
Tile opening must be prepared _dth the electrical
and _,_ater supp1} located as sho_,_n.
AdditionM Specifications
*A l 15 volt 60Hz., 15 or 20 amp power supply is
required. All individual property grounded branch
circuit or drcuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into tile back wall.
NOTE: GFI (ground ihult interrupter) is not
I'ecoI//l/lended,
_'_ater lille call enter tile opening through tile
floor or through all a(!jacent cabinet, as close to
tile back wall as possible. The water lille should be
1/4" O.D. c(_pper tubing between tile cold water
lille and water c(mnection location at tile rear of tile
retl"igerator. Installation of an easily accessible shut
off _dve in tile water line is recommended.

Installation instructions
TOOLS REQUIRED
* Tinsnips to rut banding
* Stepladder
* Bucket
* Level
* Appliance hand track
* Tubing cutter
* #2 Phillips screwdriver
* Drill and appropriate bits
* 3/8", 5/16" and 7/16" hex socket
* 1/8" Allen wrench
* Safety glasses
FLOORING
For proper installation, this refl'igerator must be placed
on a level surlhce of hard material that is at the same
height as the rest of the flooring. This sm'fi_ce should be
strong enough to support a tully loaded refi'igerator.
IMPORTANT NOTE: Protect the finish of the flooring.
Cut a large section of the cardboard carton and place
under the refrigerator where you are working.
MATERIALS REQUIRED
,b 1/4" O.D. compression nut and 2 ferrules (sleeves)
GROUNDING THE REFRIGERATOR
IMPORTANT - (Please read carefully)
FOR PERSONAL SAFETY, THIS APPLIANCE MLIST
BE PROPERI_Y GROUNDED.
The power cord of this appliance is equipped with
a 3-prong (grotmding) plug which mates with a
standard 3-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard
fl'om this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
DO NOT, UNDER ANY
CI P.CUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTEP. PLUG TO CONNECT
THE I_EFRIGEIL_TOR TO A 2-PRONG ()UTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPI JANCE.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grotmded 3-prong
wall outlet.
4

Installation instructions
ISTEP 11MODEL ZFSB25
(GO TO STEP 1A FOR
MODEL ZFSB26)
MOVE REFRIGERATOR INDOORS
iMPORTANT: l assa e,,'.>'.to
the installation location require _ 31" rain. ol)enin_, If
the opening is less than 31", the top cap and doors must
be I'eI//o_ ed.
NOTE: Skip this step if door remoxal is not required.
See instructions on next l):age, , "To Mo_e The
Refrigerator Indoors."
REMOVE THE DOORS
The top cap must be removed to access hinges. It is best
to I'eIllove ()lie door :(t ;1 tiI/le.
A. Remove 9 screws on top and 2 screws at the back of
the top cap. I,iit off top cap.
[3. Open both doors. I_,emove the 2 toekick screws and
pull %rward to remove.
C. Disconnect tile water line coupler by pushing against
tile collar on the left side. Disconnect wire harness.
D. Remove 2 screws holding top hinge to the case.
Carefully lift off door.
Follow the same procedure to remove the fresh food
doolL
NOTE: To prevent damage, leave inside
packaging, door spacer and outside
protective wrap in place until the mait is
moved to the installation location.
A
/
Wire Harness Water Line Coupler
5

Installation instructions
ISTEP 1AI MODEL ZFSB26
MOVE REFRIGERATOR iNDOORS
iMPORTANT: .oora. lpassage, a,s
into the installation location require a 36" rain. ol>ening.
If the opening is less than . r_ , the top cap and doors
must be ren/oved.
NOTE: Skip this step if door removal is not required.
See instructions on next l_age, , "To Mo_e The
Refrigerator Indoors."
REMOVE THE DOORS
The top cap must be removed to access hinges. It is best
to reillove olle door at a tiIlle.
A. Remove 2 screws and springs on top of the
retiigeratoc one on each side. Push the top cap
forward and lift up ti'om the rear.
B. Remove 2 screws holding the top filler strip, lift off.
C. Open both doors. Remove the 2 toekick screws and
pull fi)rward to remove.
D. Disc(mnect the water line coupler by pushing against
tile collar on the left side. Discoimect wire harness.
E. Remove 2 screws holding top hinge to the case.
Carefully lift off door.
NOTE: To prevent damage, leave inside
packaging, door spacer and outside
protective wrap in place until the trait is
moved to the installation location.
Follow the same procedm'e to remoxe the fresh food
door.
/
WireHarness WaterLineCoupler
6

Installation instructions
[STEP 1] ALL MODELS (continued} REINSTALLDOORS
To move the refrigerator indoors:
* Place a piece ot the carton or sott cloth against the
side panel of the refligerator to pad and protect the
stainless steel finish.
* Place the refrigerator on the handtruck with a side
against the truck only.
* Move the refi_igerator indoors.
Retbr to the illustration on page 5 or 6.
,bCarehfll> route the water line tubing and electrical
through the fl'eezer side bottom hinge. Lower the door
onto bottom hinge.
* Secm'e top hinge.
* Insert the tubing all the way into the coupler.
*Reconnect the wiring harness.
* P.eplace top filler strip (on model ZFSB26).
*Replace top cap with original screws and springs
(where present).
HINT: Llse tape or Perma Gum to prevent the spring
fl'om sliding off the screw (on model ZFSB26).
Follow the same procedure to reinstall the fi'esh food door.
[STEP 2] iNSTALL WATER LiNE
* A cold water supply is required fl)r automatic
icemaker operation. The water pressm'e must be
between 40 and 120 p.s.i.
* Route l/4" OD copper tubing between house cold
water line and the water connection location.
* Measure the distance ti'om the water x;dve on the
back of the reti'igerator to the water supply line.
Add 8 fl_ot length to allow the refligerator to be
moved away fl'om the wall after installation. Bend
the robing into 3 coils of about 10".
NOTE: The only GE approved plastic tubing is
supplied in GE SmartConnect'" Refrigerator Tubing
kits. Do not use any other plastic water supply line
because the line is under pressure at all times. Certain
types of plastic will crack or rupture with age and cause
water damage to your home.
GE Sma*_Comlect _"Refiigerator Tubing Kits are
a_ailable in the fl_llowing lengths:
2' (.6 m) - WX08X10002
6' (1.8 m) - WX08X10006
15' (4.6 m) - WX08X10015
25' (7.6 m) - WX08X10025
SaddleType
Shutoff_e
Packing
Outlet Valve
CompressionNut
\
Ferrule
(Sleeve)
* Drill a 1/4" hole in the water pipe.
* Fasten the shut-off valve to the pipe with pipe clamp.
* Tighten the clamp screws until the sealing washer
begins to swell. Do not over tighten.
* Place a compression nut and ferrule (sleeve) onto the
end of the tubing and comlect it to the shut-off _dve.
Make sine the tubing is fully insel_ed into the valve and
ferrule is tightened.
* Turn on the main water supply and flush debris.
Run about a quart of water through the robing into a
bucket. Shut oil water supply at the shut-oil x;dve.
Shut off the matin water supply.
Turn on the nearest flmcet long enough to clear the
line of water.
* Install a shut-off vah'e between the icemaker water
x:dve and cold water pipe in a basement or cabinet.
The shut-off x:dve should be located where it will be
easily accessible.
NOTE: It is best to install the x:dve into a vertical water
pipe. If you install the _alve into a horizontal water
pipe, make the com, ection at the top or side to aw)id
drawing off any sediment fi'om the water pipe.
NOTE: Saddle type shut-off valves are included in many
water supply kits. geflwe purchasing, make sure a saddle
Vpe _;dve complies with your local plumbing codes.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
7

Installation instructions
IStep2AI WATERLINE
INSTALLATION WITH
A REVERSE OSMOSIS
SYSTEM
Skip this step when not using RO System
iMPORTANT:
When connecting a (;E Reverse Osmosis Water System
to your reti'igerator, the OE RV/4Jt must be used.
For other reverse osmosis water systems, follow the
l_/a I1 tl_ ct tll'er's I'eCOl//l//ell da ti o I1s.
If tile water supply to the refl'igerator is ti'om a Reverse
Osmosis Water System, use tile retligerator's filter
b}pass plug. Using tile refrigerator's water filtration
cartridge with the RO filter call result ill hollow ice
cubes and slower water flow f_'om tile water dispenser.
Turnleft to remove Turn right to install bypass plug
[STEP 3] CONNECT WATER SUPPLY
Check to be sure that reh'igerator power cord is not
plugged into tile wall outlet.
Tubing
1/4"
CompressionNut
1/4"Tubing
(sleeve)
Refrigerator "SmartOonnectTMTubing
If you axe using copper tubing:
• Place colnpression nut and terlule (sleeve)
onto tile end of tile tubing confing fl'Oln tile
house water suppl>
•Insert tile end of tile COl)per tubing into tile
refl'igerator COlmection at tile back of tile
refl'igeratoi; as flu" as possible. Hold tile tubing
in place and tighten the fitting.
If you axe using GE SmartCom_ect'" tubing:
• Insert tile molded end of tile tubing into tile
refl'igerator COlmection, at tile back of tile
refl'igeratoi; and tighten tile conq)ression nut
until it is hand tight.
• Then tighten one additional ttlYn with a wrench.
Overtightelfing inav cause leaks.
• Fasten tile tubing into tile clamp provided to hold it
in position. You Inay need to pry open tile clami).
• Turn on tile water at tile shut-offwflve to check
fi)r leaks.
ISTEP 41CONNECT POWER
• Colmect refrigerator power cord plug to a properly
grounded receptacle.
• Check to inake Stli'e power to reliigerator is on bv
oi)elfing refl'igerator door to see if interior lights
are oix.
[STEP 5] MOVE REFRIGERATOR
INTO POSITION
• Renmxe outside protectixe wrai)i)ing.
• Moxe tile refrigerator into final installation i)osition.
• Reumxe door spacer and all inside I)ackaging.,,
8

Installation Instructions
[STEP 6] LEVEL THE REFRIGERATOR
Tile refl'igerator can be leveled by ;Mjusting the rollers
located near the bottom hinges.
Raise
Rollers
Rollers have three purposes:
* Tile rollers ac!iust so that the door closes easily when
opened about halfwa> (Raise the fl'ont about 5/8"
[l 6 mm] fl'om tile floor.)
* Rollers at!just to allow the refl'igerator to be firmly
positioned on the floor and to prevent rocking
when tile doors are opened and closed.
* Tile rollers allow you to move the refl'igemtor fi'om
the wall for cleaning.
To Adjust the Rollers:
Roller Adjusting Screw
• Use a 3/8" hex socket or wrench to turn the
ac!justment screws. Turn the screws clockwise to
raise the refligerato_; turn cotmterclockwise to
lower it.
RollerAdjustingScrews
ZFSB25 rear rollers cma also be adjusted.
• Use a 5/16" hex socket to turn the screws fl)r the
rear rollers. Turn the screws clockwise to raise the
refl_igerator, counterclockwise to lower it.
[STEP 7] LEVEL THE DOORS
If tile doors are not evenly aligned at the top, the
refl'igerator door can be a(!justed.
• Use a 7/16" hex socket or wrench to turn the door
a(!justing screw. Turn the screw to the right to raise
the (loo_; ttu'n left to lower the door.
Align at Top
NOTE: A nvhm plug is imbedded in the threads of
the pin. The plug is designed to prevent the pin fl'om
tm'ning. A wrench must be used to tm'n the pin.
•Turn tile wrench one or two times. Open and close
the refl'igerator door to check alignment with the
fl'eezer door at the top. A(!just again if necessarv_

Installation Instructions
[STEP 8] START ICEMAKER
* Flip the switch to ] (ON) position. The icemaker
will not begin to ope_'ate until it reaches its
operating temperature of 15°F (-9°C)or below.
It will then begin operation automaticall> It will
take 2-3 da_:s to fill the ice bin.
* Be sure nothing interferes with the sweep of the
feeler aim. Do not place objects in the path of the
feeler aim.
* Disca*'d the fil_t tull bucket of ice cubes.
* To turn the icemaker ott_ set the switch to (-) (OFF).
ISTEP 91TEMPERATURE
CONTROLS
* The temperature controls are preset at 37 ° fl)r the
refl_ige_'at(w and 0°F flw the fl'eeze_;
* Allow 24 hours to stabilize beflwe maldng
ac!j ustm ents.
]STEP 101 iNSTALL TOEKICK
'_ }q'ess toekick into position and l'einstall one scl'ew
on each side.
Toel<ickScrew
IMPORTANT: The vented toekick must remain
unobstructed fol" pl'oper air circtdation.
10

Notes
11

NOTE:While performing installations described in this book,
safetVglasses or goggles should beworn.
/_br Mo_'!am _/o_a[ _,!_Ji_(' h_ )our an,a, ca[[
1.800. 444.1,S'45.
NOTE: ])l'O({ll( t i1111)l-()V(tlll(flll iS _/ (Olltilltlill_ (tll(|(f[[V(W
spe(ificali_ms _)l'(f 'qll_ie(I I0 (hmlge _itl_t,1 n_lice.
Pub.No.49-60476
Dwg,No. 197D4577PO02
07-06JR
PrintedinMexico
Monogram:
GE CO/ISUlfi_r & I/Idustria/
r;E App/iances
General Electric Company
Louisville, KY 40225
go cofi)
©2006 GECompany