Monogram ZISB480DH User instructions

SECTION 1
Product Specification Revised 10/14
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
SECTION 2
1/4" FRAMED PANELS 3/4" OVERLAY PANELS
FLUSH INSET INSTALLATION
STANDARD INSTALLATION

Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
SPECIFICATIONS
Overall Width 50" (127.0 cm)†
Overall Height 84 1/2" (214.6 cm) †
Overall Depth 26" (66.0 cm) †
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 51" (129.5 cm)
Cutout Height 85" (215.9 cm)
Cutout Depth 26 3/16" (66.5 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 775 lb (351.5 kg)
FLUSH INSET INSTALLATION
Product Specification Revised 2/15
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
† Dimensions include 3/4" custom cabinet panel
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
50" (127.0)
84 1/2"
(214.6)
72 5/8"
(184.5)
68 5/8"
(174.3)
ZISB480DH
FRONT VIEW
11 11/16"
(29.7)
20 5/8" (52.4)
26" (66.0)
4"
(10.2) SIDE VIEW
* 83 1/2"
(212.1)
15 3/8"
(39.1)
*39 17/32"
(100.4)
** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
47" (119.4)
Case width
**13"
(33.0)
**20"
(50.8)
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
** Allow 4" (10.2) min
clearance to a wall
for 90˚ door swing
28 5/8"
(72.7)
TOP VIEW
*115° Door swing
Doors can be adjusted to
90° door swing
Use leveling legs and wheels for maximum 1" height
adjustment from shipping height. Nominal installation height is 84”
OVERALL DIMENSIONS
AFTER PANEL INSTALL

FLUSH INSET INSTALLATION 3/4" PANELS FLUSH INSET INSTALLATION
Product Specification Revised 2/15
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
E
FLUSH INSTALLATION
ZISB480DH
51" (129.5) Flush inset width
49 1/2" (125.7)
Width between cleats
7"
(17.8)
7"
(17.8)
3/4" (1.9)
Width of side cleats
5 1/4" (13.3)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 15/16" (53.2)
Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
WATER
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
3/4" Panel
Case
Door
6"
(15.2)
22 1/4"
(56.5)
5"
(12.7)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
85"
(215.9)
85"
(215.9)
A
B
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB480DX
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
D
C
AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area.
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
Determine your installation construction
and required anti-tip configuration:
CCut a 1" x 4" block 35” long. Measure
and mark under the soffit,
5 1/4" from the front edge of the
cabinet. Secure the wood block under
the soffit. From the bottom of the
block to the finished floor should
measure 84".
DWooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.
See Installation Instructions for
detailed instructions.
NOTES

AMounting the junction box in this
location will also allow for front
accessibility through access panel.
BWater supply area.
WARNING:
The refrigerator is top heavy and must
be secured to prevent the possibility of
tipping forward. Failure to do so may
result in death or serious injury.
The information below is for cabinet
design only. When installing the anti-
tip system you must use the product
installation instructions.
Determine your installation
construction and required anti-tip
configuration:
CCut a 1" x 4" block 35” long. Measure
and mark under the soffit,
5 3/8" from the front edge of the
cabinet. Secure the wood block
under the soffit. From the bottom of
the block to the finished floor should
measure 84".
DWooden Wall Studs and No Soffit
• Cut a 2" x 4" block and secure to
brackets provided.
• Secure brackets to back wall of
opening at 84" or your installation
height from the floor.
See Installation Instructions for
detailed instructions.
NOTES
FLUSH INSET INSTALLATION 1/2" PANELS FLUSH INSET INSTALLATION
E
FLUSH INSTALLATION
ZISB480DH
51" (129.5) Flush inset width
49 1/2" (125.7)
Width between cleats
7"
(17.8)
7"
(17.8)
3/4" (1.9)
Width of side cleats
5 3/8" (13.7)
1/2" (1.3)
26 3/16" (66.5)
Flush inset depth
20 13/16" (52.9)
Depth to cleat
FRONT VIEWSIDE VIEW
TOP VIEW
WATER
3 1/2"
(8.9)
W
Finished cleats
Finished cleats
Case Trim
1/2" Panel
Case
Door
6"
(15.2)
22 1/4"
(56.5)
5"
(12.7)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
85"
(215.9)
85"
(215.9)
A
B
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB480DX
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
D
C
Monogram®48" Built-In Side-by-Side Refrigerator ZISB480DH
Product Specification Revised 2/15

NOTES
A B C D E
50" 11 3/16" 68 5/8" 20 7/8" 28 7/8"
PANEL DIMENSIONS
FLUSH INSET 3/4" PANEL DIMENSIONS
Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed 1/2" or 3/4" custom door
and grille panels are required. For 3/4"
raised door and grille panels, routing is
required. The router depth is 1/4" all the
way around the panel’s backs. Additional
panel width reductions are required per the
diagrams shown. This will create “picture
frame” routing allowing the panels to slide
into the attached door and grille trims.
Maximum total panel weight:
• Fresh food door panels – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
Door Handles
Door handle not included. A custom handle
supplied by your cabinet maker may be used.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" panels. Kit includes
one handle – 30 1/2" long.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" panels. Kit includes
one handle – 64 1/4" long.
FLUSH INSET INSTALLATION
Product Specification Revised 2/15
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
Grille Panel
Freezer
Panel
Dispenser
Cutout
Fresh
Food
Panel
A
B
C
F
G
D E
F G
17 23/32" 5 3/8"
DISPENSER CUTOUT
POSITION
Dispenser
Cutout
9 5/8"
(24.4)
15 3/8"
(39.1)
3/4" RAISED DOOR PANEL ROUTING
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
HINGE
SIDE
HANDLE
SIDE
Front
Back
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
3/4"
11/32"
1/4"
3/32"
1/4" 11/32"
DETAIL TOP
DETAIL BOTTOM
2 1/16" 3/16"
ROUTER DEPTH 1/4"
DETAIL HINGE
SIDE
DETAIL HANDLE
SIDE

NOTES
Trimmed refrigerators are designed
to be customized with decorative
panels. Field-installed 1/2" or 3/4"
custom door and grille panels are
required. For 3/4" raised door and grille
panels, routing is required. The router
depth is 1/4" all the way around the
panel’s backs. Additional panel width
reductions are required per the diagrams
shown. This will create “picture frame”
routing allowing the panels to slide into
the attached door and grille trims.
Maximum total panel weight:
• Fresh food door panels – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs.
Door Handles
Door handle not included. A custom
handle supplied by your cabinet maker
may be used.
ZKHPSS1: Professional tubular stainless
steel handle designed to fit 3/4" panels.
Kit includes one handle – 30 1/2" long.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" panels. Kit
includes one handle – 64 1/4" long.
FLUSH INSET INSTALLATION
Monogram®48" Built-In Side-by-Side Refrigerator
3/4" RAISED GRILLE PANEL ROUTING
Front
NOTE: Routed areas should be
finished as they may be visible
when assembled.
CORNER VIEW SHOWING
“PICTURE FRAME” ROUTING
Back
TOP
FrontBack
BOTTOM
3/4" PANEL SIDE VIEW
(AFTER ROUTING)
3/16"
DETAIL TOP
DETAIL BOTTOM
ROUTER DEPTH 1/4"
2"
2 1/16" 2 1/16"
ROUTER DEPTH 1/4" ROUTER DEPTH 1/4"
DETAIL
LEFT SIDE
DETAIL RIGHT
SIDE
3/4" PANEL BOTTOM VIEW
(AFTER ROUTING)
LEFT
SIDE
RIGHT
SIDE
Front
Back
ZISB480DH
Product Specification Revised 2/15

NOTES
DISPENSER TRIM
RAISED PANEL DESIGN ON DISPENSER MODELS
3/4" OVERLAY PANEL
DISPENSER TRIM
1/2" OVERLAY PANEL
DISPENSER TRIM
A
16 3/4"
10 5/8"
DISPENSER TRIM
SIDE VIEW CROSS SECTION
(Showing Raised Panel with
Middle Rail)
Product Specification Revised 2/15
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
These refrigerators are supplied with a
dispenser trim for flush inset panels.
APanel Dispenser Trim:
The provided dispenser trim is designed
to fit a total panel thickness of 3/4"
or 0.85".
• If the panel is less than 3/4" thick, a
noticeable gap may be created around the
dispenser trim.
• If the panel is more than 0.85" thick, the
dispenser trim cannot be secured to
the door.
• The overlay panel must be constructed
according to the specifications shown to
achieve the correct total thickness.
• When a raised panel design is to be used,
a custom middle rail is required.
Raised Panel Design on Dispenser Models:
When a raised panel design is to be used,
a custom wide middle rail is required to
accept the dispenser trim.
B• The middle rail must be wide enough
to allow for the dispenser trim to
overlap the opening.
C• The middle rail must be 3/4" total
thickness for 3/4" panels or 0.85" total
thickness for 1/2" panels to accept the
dispenser trim.
FLUSH INSET INSTALLATION
Freezer Door
3/4" Flush Panel
Ice/Water Dispenser
Freezer Door
1/4" Backer Panel
.10" Spacer Panel
1/2" Overlay Panel
Ice/Water Dispenser
.85"
Total
Thickness
3/4" or 1/2" Flush Panel
3/4" or .85"
Total
Thickness
C
B

A B C D
Fresh Food Panel 2 1/16" 1/16" 1/8" 1/8"
Freezer Panel 2 1/16" 1/16" 1/8" 1/8"
Grille Panel 2 1/16" 2 1/16" 1 15/32" 7/32"
PANEL DIMENSIONS
PANEL DIMENSIONS
FLUSH INSET 1/2" PANEL DIMENSIONS
The 1/2" overlay panel must be secured to
a .10" spacer panel and a 1/4" thick backer
panel, which slides into the trim.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer
panel, left to right and top to bottom.
Secure the panels with glue.
• Refer to the chart for locating the backer
panel to the overlay panel. Secure the
overlay panel to the backer panel with glue
and screws. Screws must be countersunk
into the backer panel.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs.
FLUSH INSET INSTALLATION
Monogram®48" Built-In Side-by-Side Refrigerator
NOTES
1/4" BACKER ASSEMBLY ROUTING DIMENSIONS
Freezer
Back
Hinge Side
Fresh Food
Back
Backer with
Overlay Panel
Assembly
AAB B
CC
DD
1/2"
Overlay
Panel
1/4"
Backer
Panel
Door
.10"
Spacer
C
D
A B
Grille Back
ZISB480DH
Product Specification Revised 2/15
Grille Panel
Freezer
Panel
Dispenser
Cutout
Fresh
Food
Panel
A
B
C
F
G
D E
F G
17 23/32" 5 3/8"
DISPENSER CUTOUT
POSITION
Dispenser
Cutout
9 5/8"
(24.4)
15 3/8"
(39.1)
A B C D E
1/4" Backer Panel 45 7/8" 9 1/2" 68 3/8" 18 9/16" 29 9/16"
.10" Space Panel 45" 8 5/8" 67" 17 9/16" 25 9/16"
1/2" Overlay Panel 50" 11 3/16" 68 5/8" 20 7/8" 28 7/8"

OVERALL DIMENSIONS
Dimensions in parentheses are in centimeters unless otherwise noted.
Actual product dimensions may vary due to manufacturing tolerances.
STANDARD INSTALLATION
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp power supply
is required. An individual properly grounded
branch circuit or circuit breaker is recommended.
Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
SPECIFICATIONS
Overall Width 48" (121.92 cm)
Overall Height 84" (213.36 cm)
Overall Depth 25 3/8" (64.453 cm)
Door Clearance 28 5/8" (72.1 cm)
Cutout Width 47 1/2" (120.7 cm)
Cutout Height 83 1/2" - 84 1/2"
(212.1 - 214.6 cm)
Cutout Depth 24" (61 cm)
Plumbing Requirements 1/4" OD copper
tubing or GE
SmartConnect kit
Shipping Weight 775 lb
*84"
(213.4)
48" (121.9)
25 1/2" (64.8)
23 7/8" (60.7)
1 3/4"
(4.4)
*72 1/4"
(183.5)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
47" (119.4)
Case width
26 5/8"
(67.6)
TOP VIEW
13 1/2"
(34.3)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
(9.5)
ZISB480DX
SIDE VIEWFRONT VIEW
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.
** Allow 15" (38.1) min
clearance for 130˚
door swing
** Allow 20" (50.8) min
clearance for 130˚
door swing
*84"
(213.4)
48" (121.9)
25 1/2" (64.8)
23 7/8" (60.7)
1 3/4"
(4.4)
*72 1/4"
(183.5)
*3 1/2"
(8.9)
*83 1/2"
(212.1)
47" (119.4)
Case width
26 5/8"
(67.6)
TOP VIEW
13 1/2"
(34.3)
*40"
(101.6)
68 1/2"
(174.0)
*3 3/4"
(9.5)
ZISB480DX
SIDE VIEWFRONT VIEW
* Shipping height. Use leveling legs and wheels for maximum
1" height adjustment from shipping height.
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** Allow 4" (10.2) min
clearance to a wall for 90˚
door swing
** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door
swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow
full 130° door swings for pan removal. If the 90° door stop position is used, pan access is
maintained, but pan removal is restricted.
** Allow 15" (38.1) min
clearance for 130˚
door swing
** Allow 20" (50.8) min
clearance for 130˚
door swing
Product Specification Revised 2/15
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator

NOTES
STANDARD INSTALLATION STANDARD INSTALLATION
Product Specification Revised 2/15
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
ANTI-TIP BRACKET
FRONT VIEW SIDE VIEW
W
24" (61.0)
1 1/2"
(3.8)
3 1/4"
(8.3)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
E
WATER
47 1/2" (120.7)
20" (50.8)
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
6"
(15.2)
5"
(12.7)
5"
(12.7)
5"
(12.7)
ZISB480DX
SIDE VIEW INSTALLED
UNDER SOFFIT
SOFFIT
SIDE VIEW INSTALLED
WITH WOODEN WALL STUDS
AND NO SOFFIT
*84"
(213.4)
*Or installation
height from floor
2" x 4"
Cut to 35" Length
Screws mounted
into vertical wall
studs
FRONT VIEW INSTALLED
WITH METAL WALL STUDS
AND NO SOFFIT
Top Case Trim
3/4"
Min.
Side View Top
Case Trim
Install Screws
Through Trim and Into
3/4" Min. Wood Brace
D
C
E
AMounting the junction
box in this location will
also allow for front
accessibility through
access panel.
BWater supply area.
WARNING:
The refrigerator is top
heavy and must be secured
to prevent the possibility of
tipping forward. Failure to
do so may result in death
or serious injury.
The information below is
for cabinet design only.
When installing the anti-
tip system you must use
the product installation
instructions.
Determine your installation
construction and required
anti-tip configuration:
CInstalled Under Soffit
After installing unit into
installation opening,
raise grille panel and
screw metal case sides to
adjacent cabinet. When
installed under a soffit, the
soffit cannot exceed 24"
deep. The top case trim
overlaps the bottom of
the soffit.
DWooden Wall Studs and
No Soffit
• Cut a 2" x 4" block and
secure to brackets
provided.
• Secure brackets to back
wall of opening at 84" or
your installation height
from the floor.
EMetal Wall Studs and
No Soffit
This method requires
securely fastened cabinets
on both sides and a 3/4"
minimum wood brace
above unit, with it’s front
surface 24" from back wall.
• After installing unit into
opening, raise grille panel
and attach metal case
top trim to 3/4" minimum
wood brace.
• The brace spanning
the enclosure must be
securely fastened to
cabinets on both sides.
See Installation
Instructions for detailed
instructions.
STANDARD INSTALLATION
ZISB480DH
24" (61)
1 9/16"
(3.97)
3 1/8"
(7.93) 47 1/2" (120.7)
7/16" (1.1)
Trim overlap
3 1/2"
(8.9)
3 1/2"
(8.9)
75"
(190.5 )
From floor
to bottom
of electrical
area
*84 1/2"
(214.6)
*Trim will overlap
additional 7/16"
SIDE VIEW
FRONT VIEW
TOP VIEW
5"
(12.7)
5"
(12.7)
WATERW
6"
(15.24)
20" (50.8)
5"
(12.7)
E
A
BThe refrigerator
will project
forward, slightly
beyond adjacent
cabinetry.

ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
Product Specification Revised 2/15
CUSTOM SIDE PANELS
F
2 9/16"
(6.5)
*3" - 4"
(7.6 - 10.2)
*Depending
on installation
height
1 7/8"
(4.8)
24" (61.0)
3/16"
(.5)
*84”
(213.4)
*Depending
on installation
*84"
(213.4)
*Depending
on installation
height
ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH
ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH
NOTES
STANDARD INSTALLATION
FSide panels must be
used whenever the sides
of the refrigerator will
be exposed. The 1/4"
side panels will slip
into the side case trim.
Secure the panels to
the refrigerator with
stick-on hook and loop
fastener strips. Order
the side panels from the
cabinet manufacturer.

NOTES
3/4" Overlay Panels:
For 3/4" thick custom panels ordered from
your cabinet maker; the decorative panels
slide into the trim.
The overlay panel must be secured to a
1/4"-thick backer panel which slides into
the trim. A spacer panel 0.10" thick must
be placed between the overlay and backer
panels.
Center each panel over the other. Assemble
the panels with glue and screws. Screws
must be countersunk into the backer panel.
NOTE: Left-to-right offset is not always equal
to top-to-bottom offset.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
Door Handles:
The supplied handles can be adjusted to
accommodate both framed or overlay panels.
Custom handles of your choice, supplied by
your cabinet maker, can also be installed.
ZKHPSS1: Professional tubular stainless steel
handle designed to fit 3/4" overlay panels.
ZKHSS2: European tubular stainless steel
handle designed to fit 3/4" overlay panels.
Kits include one handle. Order 2 kits for
side-by-side refrigerators from your
Monogram supplier.
Trimmed refrigerators are designed to
be customized with decorative panels.
Field-installed custom door and grille
panels are required.
1/4" Framed Panels:
For 1/4" thick custom panels ordered from
your cabinet maker; the decorative panels
slide into the trim.
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer drawer panel – 53 lbs.
• Grille panel – 18 lbs
STANDARD INSTALLATION
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
Product Specification Revised 2/15
PANEL ASSEMBLY CROSS SECTION
Door
1/4" Backer Panel
.10" Spacer Panel
Supplied Handles
Trim
3/4" Overlay Panel
3/4" OVERLAY PANEL DIMENSIONS
1/4" FRAMED PANEL DIMENSIONS
Door
1/4" Framed Panel
Supplied Handles
Trim
PANEL ASSEMBLY CROSS SECTION
A B C D E
1/4" Backer Panel 45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"
.10" Spacer Panel 45" 8 5/8" 67" 17 1/4" 25 1/4"
3/4" Overlay Panel 46 1/8" 9 3/4" 68 5/8" 18 13/16" 26 13/16"
A B C D E
1/4" Framed Panel 45 7/8" 9 1/2" 68 3/8" 18 9/16" 26 9/16"
Grille Panel
Freezer
Panel
Dispenser
Cutout
Fresh
Food
Panel
A
B
C
F
G
D E
Grille Panel
Freezer
Panel
Dispenser
Cutout
Fresh
Food
Panel
A
B
C
F
G
D E
F G
17 13/16" 5 1/8"
DISPENSER CUTOUT
POSITION
PANEL DIMENSIONS
Dispenser
Cutout
9 5/8"
(24.4)
15 3/8"
(39.1)
F G
17 15/16" 5 1/4"
.25" + .10" + .75" = 1.10" Total Panel Thickness
PANEL DIMENSIONS
*DISPENSER CUTOUT
POSITION
* Cut the dispenser opening after the backer, spacer
and overlay panels have been assembled.
Dispenser
Cutout
9 5/8"
(24.4)
15 3/8"
(39.1)

ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
Product Specification Revised 2/15
STANDARD INSTALLATION
DISPENSER TRIM
RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS
1/4" PANEL DISPENSER TRIM 3/4" OVERLAY PANEL DISPENSER TRIM
Freezer Door
1/4" Framed Panel
Ice/Water Dispenser
1/4"
Total
Thickness
Freezer Door
1/4" Backer Panel
.10" Spacer Panel
3/4" Overlay Panel
Ice/Water Dispenser
1.10"
Total
Thickness
A B
16 3/4"
10 5/8"
1/4" Backer Panel
3/4" Overlay Panel
.10" Spacer
1.10”
Total
Thickness
D
C
DISPENSER TRIM
SIDE VIEW CROSS SECTION
(Showing Raised Overlay
with Middle Rail)
NOTES
These refrigerators are supplied with two
dispenser trims, one for framed panels
and one for overlay panels.
1/4" Panel Dispenser Trim:
The framed panel must be 1/4" nominal
thickness to fit the dispenser trim.
• The dispenser trim ts over the custom
panel and snaps into the freezer door.
• If the panel is less than 0.250" thick, a
noticeable gap may be created around
the dispenser trim. Foam tape may be
applied on the door to improve the fit.
• If the panel is more than 0.250" thick,
the dispenser trim cannot be secured
to the door.
3/4" Overlay Panel Dispenser Trim:
The 3/4" overlay dispenser trim is
designed to fit a total panel thickness
of 1.100".
• If the panel is less than 1.100" thick, a
noticeable gap may be created around
the dispenser trim.
• If the panel is more than 1.100" thick,
the dispenser trim cannot be secured
to the door.
• The overlay panel must be constructed
according to the specifications shown
to achieve the correct total thickness.
• Alternative panel construction methods
such as securing a 3/4" panel to a 1/4"
backer panel cannot be used. Another
method, routing a 3/4"-thick panel
on all sides, cannot be used. These
methods will not result in the required
1.100" panel thickness.
• When a raised panel design is to be
used, a custom middle rail is required.
Raised Overlay Panel Design on
Dispenser Models:
When a raised panel design is to be used,
a custom wide middle rail is required to
accept the dispenser trim.
• The middle rail must be wide enough to
allow for the dispenser trim to overlap
the opening.
• The middle rail must be 1.10" total
thickness to accept the dispenser trim.

FEATURES AND BENEFITS
ZISB480DHMonogram®48" Built-In Side-by-Side Refrigerator
Product Specification Revised 2/15
R
Halogen Light Columns - Located in the freezer
and fresh food compartments, extend the full
length of the interior compartments providing
brilliant, all-level illumination
LED Lighting - Located at the top of the fresh
food compartment, and inside the vegetable and
climate-control drawers, illuminates contents
without compromising space
Advanced Temperature Management System
with Multi-Shelf Air Tower - Provides even
distribution of air throughout the refrigerator
Climate-Control Drawer - Allows you to express-
chill beverages, express-thaw meats and select
specific temperatures for perishable foods
Dispenser with Proximity Sensor - Designed
to accommodate glassware of all sizes, from
pitchers to tumblers; control graphics light up as
you approach and automatically switch off when
you walk away
Dairy Bin with Center Divider - Has a unique
magnetic seal that locks in freshness
Filter-Change Indicator Light - Located on the
upfront control panel, provides a visual reminder
when it's time to replace the filter for the water
dispenser
GE®Water Filter - Has been moved from the
fresh food compartment to the overhead cabinet,
where it is discreetly out of sight
Drop-Down Shelf - Provides additional space
for a casserole dish or pizza box