Monoprice 13815 User manual

Aluminum Dual Monitor Desk Stand 15" - 30"
P/N: 13815
User's Manual

2
INTRODUCTION
Thank you for purchasing this Dual Monitor Desk Stand!
This desk stand is capable of mounting two 15 " ~ 30" monitors, with 75 x 75 or 100 x 100
VESA® mounting patterns and weighing up to 22 lbs. each. It allows for overall height,
individual height, tilt, swivel, and horizontal adjustments, and includes cable management
clips and all the hardware necessary to assemble the stand and mount two monitors.
Additionally, the monitors can be rotated 360° for easy portrait/landscape orientation
adjustment.
FEATURES
Compatible with 15" ~ 30" monitors
Supports two monitors weighing up to 22 lbs. (10 kg) each
Compatible with 75 x 75 and 100 x 100 VESA® mounting patterns
Overall height, individual height, tilt, swivel, rotation, and horizontal position
adjustments
Includes cable management clips
Includes all necessary mounting hardware
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering,
purchasing, and delivery experience is second to none. If you have any problem with your
order, please give us an opportunity to make it right. You can contact a Monoprice
Customer Service representative through the Live Chat link on our website
www.monoprice.com during normal business hours (Mon-Fri: 5am-7pm PT, Sat-Sun: 9am-
6pm PT) or via email at [email protected]

3
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the items listed
below. If anything is missing or damaged, please contact Monoprice Customer Service for a
replacement.
AArm Assembly
BBase
CPole Assembly
Dø8.0 x ø5.5 x 5.0 mm Bushings (x8)
EShort M4x12 Screws (x8)
FLong M4x12 Screws (x8)
G4mm Hex Wrench
H5mm Hex Wrench

4
INSTALLATION
1. Place the Base (B) on a desk or table.
2. Insert the Pole Assembly (C) into the hole in the base,
then turn it clockwise to tighten the connection.
3. Place the Arm Assembly (A) onto the Pole Assembly
(C), adjust the height as desired, then use the 4mm
Hex Wrench (G) to tighten the screw as shown in the
following figure to the right. You can also adjust the
height by loosening the lock collar and extending the
pole assembly up or down as desired.
4. Place a towel or blanket on a table or on the floor, then place one of your monitors
face down on the towel/blanket.
5. Insert two (2) Short M4x12 Screws (E) or Long M4x12 Screws (F) into the upper two
VESA® mounting holes. Tighten them to the point where there is 2-4mm between
the back of the monitor and the screw head. If necessary, use the ø8.0 x ø5.5 x 5.0
mm Bushings (D) to reduce the space between the screw heads and the back of the
monitor.

5
6. Repeat steps 4 and 5 for the second monitor.
7. Place one of the monitors onto a mounting bracket by placing the extended screws
into the grooves on the bracket.
8. Insert two (2) additional Short M4x12 Screws (E) or Long M4x12 Screws (F) through
the bracket into the lower VESA® mounting holes. Tighten the screws to secure the
bracket to the back of the monitor. Use the ø8.0 x ø5.5 x 5.0 mm Bushings (D) as
necessary to reduce the space between the screw heads and the back of the
monitor.
9. Repeat steps 7 and 8 for the second monitor.

6
10. Loosen the two thumbscrews that hold each bracket to the mounting arm, then
slide the monitor and bracket assemblies so that the monitor bezels are almost
touching at the center of the desk mount assembly, as shown in the figure to the
right. Tighten the thumbscrews to secure the brackets in place.
11. If the monitors are not level, use the included 4mm Hex Wrench (G) to tighten the
screw at the top of the lower bracket, thereby raising the bracket's level. To lower
the bracket's level, loosen the screw.

7
12. To adjust the tilt, first use the included 5mm Hex Wrench (H) to slightly loosen the
two screws on each side of the mounting bracket, adjust the tilt as desired, then
tighten the screws to secure the bracket in place.
13. To adjust the monitor angles, use the included 5mm Hex Wrench (H) to slightly
loosen the two screws at the base of the arms, adjust the angle, then tighten the
screws to secure the arms in place.
14. Install the cables and use the included cable management clips to keep hold the
cables neatly in place.

8
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist you with any
questions you may have about installation, setup, troubleshooting, or product
recommendations. If you ever need assistance with your new product, please come online
to talk to one of our friendly and knowledgeable Tech Support Associates. Technical
support is available through the online chat button on our website www.monoprice.com
during regular business hours, 7 days a week. You can also get assistance through email by
sending a message to [e-mail]
SPECIFICATIONS
Model
13815
Number of Supported Monitors
Two (2)
Supported TV Sizes
15" ~ 30"
Maximum Supported Weight
22 lbs. (10 kg) per monitor
Supported VESA Sizes
75 x 75 and 100 x 100
Height Adjustment Range
11.2" ~ 17.7" (284 ~ 450 mm)
Swivel Adjustment Range
Up to 150°
Rotation Adjustment Range
360°
Tilt Adjustment Range
±12°
VESA® is a registered trademark of the Video Electronics Standards Association.