Selby PLB161 User manual

1
Installation Instruction
English
UNPACKING INSTRUCTIONS
! Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.
! Check package contents against the Supplied Parts List in the next page to assure that all components were received
undamaged. Do not use damaged or defective parts.
! Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before beginning the installation, and carefully
follow all instructions contained herein. Use proper safety equipment during installation.
Please call a qualified installation contractor for help if you:
! If you don't understand these directions or have any doubts about the safety of the installation.
! If you are uncertain about the nature of your wall, consult a qualified installation contractor.
Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby
disclaim any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of
this product.
CAUTION!
WARNING
!This TV mount must be securely attached to the vertical wall. If the mount
is not properly installed it may fall, resulting in possible injury and/or
damage.
Note: The mounting components and hardware supplied in this package are not designed for installations to
walls with steel studs or to cinder block walls. If the hardware you need for your installation is not included,
please consult your local hardware store for proper mounting hardware for the application.
Tools Required 5/32"(4mm) Drill Bit
Phillips Screwdriver
3/8"(10mm) Masonry Bit
Stud Finder
Wrench or Socket Set
Carpenter's Level

(4)M4x20 Bolt-d (4)M5x20 Bolt-e (4)M6x20 Bolt-f (4)M8x20 Bolt-g
2
Supplied Par ts List
(4)M4/M5 Washer-l (4)M6/M8 Washer-m
(4)M4 Lock Washer-h (4)M5 Lock Washer-i (4)M6 Lock Washer-j (4)M8 Lock Washer-k
(2)Wall Plate-a1 (1)Right Monitor Bracket-c (1)Left Monitor Bracket-b
(4)Lag Bolt-o
(4)Lag Bolt Washer-p (4)Concrete Anchor-q
(4)5mm Plastic Space-n
(2)Wall Plate-a2
(4)M5x6 Bolt-r

First of all, make sure the diameter of the Bolt(d,e,f,g) your TV requires. Once you have determined the correct diameter,
please see the relative diagram as below. You will thread the Bolt into the TV using the correct Lock Washer(h,i,j,k) and
Washer(l,m). You can use the Plastic Space(n) if the bolt is too long. Please make sure the Monitor Brackets(b,c) are
vertically centered and level with each other.
Mounting the Monitor Brackets to the TV
Step 2
3
M4 Diameter Bolt M6 Diameter Bolt
Diagram 2
d
h
l
b
f
j
m
c
M5 Diameter Bolt
e
i
l
b
M8 Diameter Bolt
g
k
m
c
nn
n
n
Assemble the Wall Plate by 4pcs M5x6 bolt(r) as below diagram.
Assemble the Wall plate
Step 1
a2
a1
r

4
Thanks for choosing our products, enjoy the using.
Warning: Some TVs may require two people to lift! We are not responsible for personal injury or product damage.
First hook the Monitor Brackets(b,c) over the top of the wall Plate(a), then let the bottom of the Monitor Brackets rotate to
the bottom of the Wall Plate as shown in the Diagram 4A. Use the screw driver to tighten the safety bolts. Then the Monitor
Bracket will sit behind the bottom tab on the Wall Plate as shown in the Diagram 4B.You may have to loosen the
safety screw if you change the small tilting angel to large tilting angel, oppositely, you may have to
fasten the safety screw again if you change the large tilting angel to small tilting angel.
Attaching Monitor to Wall Plate and Adding the Safety Bolts
Step 4
Diagram 4A Diagram 4B
a
b,c b,c
a
safety bolt
wall wall
Brick, Solid Concrete and Concrete Block mounting:
Use the Wall Plate(a) as a template to mark 4 hole locations on the wall. Two in the top row of slots and two more in the
bottom row. Make sure these holes are level and there is at least 6"(150mm) distance between two holes. Pre-Drill these
holes with a 3/8"(10mm) masonry bit to at least 2.4"(60mm) in depth. Insert a Concrete Anchor(q) into each of these holes.
Make sure the anchor is seated completely flush with the concrete surface even if there is a layer of drywall or other
material in front. Attach the Wall Plate to the wall using 4pcs Lag Bolts(o), 4pcs Lag Bolt Washers(p) and 4pcs Concrete
Anchor(q), shown in Diagram 3A.
Wood Stud mounting:
The Wall Plate(a) must be mounted to two wood studs at least 16"(406mm) apart. Use a stud finder to locate two
adjacent studs. It is a good idea to verify where the studs are located with an awl or thin nail shown in Diagram 3B. Pre-drill
a 2.4"(60mm) deep hole at the desired height in each stud using a 5/32"(4mm) drill bit. Make sure these holes are in the
center area of the studs and level with each other. Use the Wall Plate as a template to mark the location of the second hole
in each stud. Drill 2.4"(60mm) deep holes using the 5/32"(4mm) drill bit in the marked locations. Attach the Wall Plate to
the wall using the 4pcs Lag Bolts(o) and 4pcs Lag Bolt Washers(p).
Mounting the Wall Plate to the Wall
Step 3
16 inch
16 inch
16 inch
Diagram 3BDiagram 3A
Stud Finder
op
q