Monster Moto MM-E250 User manual

This operator’s manual contains important safety informaon and maintenance
informaon. Read it carefully before using this vehicle. Failure to follow the warnings
contained in this operator’s manual could result in INJURY or DEATH.
Keep this manual in a safe place. It is very important that this owner’s manual be
reviewed by all riders and it should be considered a permanent part of the mini bike
and should remain with the vehicle when transferred to a new owner.
This manual contains the latest product informaon available before prinng. Due to
product improvements or producon changes, there could be discrepancies between
the informaon contained in this manual and accurate product informaiton. Monster
Moto, LLC (Monster Moto) reserves the right to make changes to its products at any me,
without noce and without obligaon to make the same or similar changes to any vehicle
previously built or sold.
No part of this publicaon may be reproduced or copied without wrien permission
from Monster Moto.
© Monster Moto, LLC, 2013
Owner’s Manual
Monster Moto, LLC
1001 S. Jupiter Rd.
Garland, TX 75042
Phone: [phone]
All rights reserved. © 2013
MADE IN CHINA
MM-E250
Electric Mini Bike

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
2
Contents
Warranty 1
Introducon and Safety Messages 2 - 5
Operang Controls 5 - 7
Inial Set-Up 8
Pre-Ride Checklist 9
Basic Operaon 10 -11
Maintaining your Mini Bike 12-15
Rear Brake Adjustment 12
Drive Chain 13
Tire Pressure 14
Fuse Replacement 14
 BaeryReplacement 15
Troubleshoong 16 - 18
Product Registraon 19 - 20

855-833-6483 OR EMAIL US AT [e-mail]
1
Warranty Informaon
Congratulaons on your decision to purchase a Monster Moto power sports product! We are
pleased that you have chosen a Monster Moto product, and we are dedicated to supporng your
successful and safe power sports recreaon experience!
We are grateful for your business, and in order to assure your quality experience, please review
and make note of the following warranty related issues:
KEEP YOUR RECEIPT: Proof of purchase will be required to substanate any warranty claim.
WHAT IS COVERED: Monster Moto warrants to the original retail purchaser of this Product that this
Product is free from defects in material or workmanship and agrees, at Monster Moto’s discreon,
to either repair, provide replacement parts for, or replace (without charge or labor), any product
component having a material defect for a period of ninety (90) days from the date of purchase,
except as limited below. Monster Moto may require the purchaser to return to Monster Moto, at
their expense, the part claimed to be defecve for Monster Moto’s inspecon, at which me the
returned parts or product become property of Monster Moto.
WHAT IS NOT COVERED: This warranty does not cover any condions caused by misuse, neglect,
negligence, accident or operaon in any way contrary to the operang instrucons located in the
operator’s manual. Normal wear, alteraon, modicaon, improper or inadequate maintenance,
or use of unauthorized replacement parts or service provided by anyone other than an Authorized
Monster Moto Service Center are not covered under this warranty. This warranty does not cover
products used for rental or commercial purposes or used in compeon, nor does it cover
transportaon costs for warranty service. Without liming the above, this warranty is VOID with
respect to any product that has sustained damage resulng from impacts, accidents, jumping,
or any other uses considered outside of the scope of normal and safe operaon.
LIMITATIONS OF LIABILITY: This Warranty is non-transferable aer the Product’s inial sale. No
unapproved modicaons can be made to the Product, its performance or otherwise, in order for
this Limited Warranty to remain in eect. No reimbursement is provided for towing, loss of me, loss
of use, inconvenience, incidental or consequenal damages. This Limited Warranty covers only parts
and labor due to manufacturer defect. This Warranty does not cover minor surface blemishes, rips,
tears, or other cosmec damages due to normal use, or other intenonal or unintenonal damage to
the Product. This Limited Warranty will not cover any damage which results from the applicaon of
improper cleaners, solvents or chemicals to the Product, or from smoke or soot, or from exposure to
saltwater, sea breeze or salt. This Limited Warranty will not cover any damage resulng from product
storage in the elements. This Limited Warranty does not cover improper repair or misdiagnosis of
product problems.
OWNER'S RESPONSIBILITIES: As the vehicle owner, you are responsible for performing required
maintenance and maintaining a record of all receipts for maintenance performed on your mini bike.
Your warranty claim may be denied solely because of your failure to ensure the performance of all
scheduled maintenance or lack of maintenance records or receipts. As the vehicle owner, you may
be denied your warranty coverage if your vehicle or a part has failed due to abuse, neglect, improper
maintenance or unapproved modicaons.

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
2
Introducon
Your Monster Moto MM-E250 electric mini bike was designed as a recreaonal mini bike
for a single rider. This mini bike is ideal for younger riders with basic experience.
Always check and obey any local laws or regulaons which may aect the locaon the
MM-E250 may be used and safely operated. This vehicle is intended for use on solid, at,
clean and dry surfaces such as pavement or level ground without loose debris such as
gravel or dirt. Icy or rough terrain can create hazardous riding condions resulng
in an accident. Do not operate in wet condions or through standing water because you
can permanently damage the electrical system and components. Never use the MM-E250
on carpet or indoor ooring because it will damage those surfaces. Be careful to watch for
pedestrian trac wherever you ride your MM-E250. The bike is built for smaller riders.
Before riding, please take your me to get acquainted with your MM-E250 and how it
works. To protect your investment, we urge you to keep it well maintained. In addion
to regular maintenance, it is important to observe and perform all pre-ride and periodic
checks outlined in this manual. In this manual, you will nd helpful safety informaon,
instrucons, facts, and helpful ps. To make it easier to use, there is a table of contents
at the beginning.
As you read through this manual you will nd informaon that is preceded with a NOTICE
symbol. This informaon is intended to help you avoid damage to your mini bike. This
manual covers basic maintenance procedures.
Read the warranty page carefully so that you understand the coverage on your mini bike
and are aware of your rights and responsibilies.
If you have any quesons or you need any special service or repair, remember that
your Monster Moto authorized service center knows your mini bike best and will be
dedicated to your complete sasfacon. Replacement parts and technical support can be
obtained online at www.monstermoto.com or by phone at 855-833-6483. Please be sure
to register your Monster Moto product and nofy us of any address changes so we may
contact you in the future with any important product informaon.
You can also visit our website at www.monstermoto.com to view service videos and
informaon about all Monster Moto products.

855-833-6483 OR EMAIL US AT [e-mail]
3
Important Safety Informaon
Your personal safety, and the safety of those around you, is extremely important. Operang this
mini bike safely is an important responsibility.
Monster Motor has provided operang procedures and other informaon on labels on your mini bike
and in this manual to help you make informed decisions about safety. This informaon will alert you
to potenal hazards that could harm you or others.
It is understood that it is not praccal or possible to warn you about all possible hazards associated
with operang and maintaining a mini bike. You must use your own good judgment.
Safety informaon will come in a variety of dierent forms, including:
•Safety Labels on the mini bike
• Safety Messages preceded by a safety symbol and one of these three signal words:
DANGER, WARNING or CAUTION.
Below are the denions of these three words:
You WILL be KILLED or SERIOUSLY INJURED if you do not follow instrucons.
You CAN be KILLED or SERIOUSLY INJURED if you do not follow instrucons.
You CAN be INJURED if you do not follow instrucons.
•Safety Headings such as important safety reminders and/or precauons.
•Safety Secons such as mini bike safety.
•Instrucons on how to use the mini bike safely and correctly.
This enre manual is lled with important safety informaon - please read it carefully.
!
DANGER
!
WARNING
!
CAUTION
!

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
4
Important Safety Informaon
A mini bike can provide many years of service and pleasure, provided you take responsibility
for safety, properly maintain your mini bike and understand the challenges you may
encounter while riding.
This mini bike has been designed for younger riders. However, not all youngsters meet the
physical and emoonal levels that are needed for riding. Before parents allow any children
to ride this mini bike, we strongly recommend that both of you read this enre manual so
you are fully informed before deciding if your children are ready to ride. Listed below are
some of the most important safety measures one should take when riding.
Ride with proper are The following statement is a proven fact: ``Helmets
signicantly reduce the number and severity of head injuries.” Never ride your mini bike
without a helmet or eye protecon. Even a crash at slow speed can result in a fatal head
injury if you are not wearing a helmet. Monster Moto recommends wearing helmets that
have been cered for safety by helmet tesng organizaons which are independent
from the helmet manufacturer. We also recommend that you wear other approved safety
gear such as elbow and knee pads. Always wear shoes, keep laces ed, and never ride
barefooted or with sandals.
Never Carry a Passenger This mini bike has been designed for ONE rider
only. There are no passenger pegs, footrests, handles or seat room for a passenger. Riding
with a passenger can interfere with your ability to operate and/or control the mini bike
and may result in serious injury or death.
Ride O-Road Only This mini bike has been designed and manufactured
for o-road use only. The mini bike is not equipped with lights, turn signals, horn and other
features required to drive a mini bike on public roads.
Ride Within Your Limits Never aempt to ride your mini bike in a manner
that is beyond your skill level. It takes me to learn proper riding skills. Learn to ride your
mini bike step by step. Start by praccing on safe terrain at slow speeds and gradually
build your skill level. Instrucon from an experienced rider(s) is highly recommended.
Parental Supervision Required The MM-E250 is an electric power sports
vehicle and not a toy. The recommended rider age of 8 or older is only an esmate and
can be aected by the rider’s maturity levels, weight and skills. Any rider who cannot
comfortably t on the mini bike should not ride the unit.
Keep small children away from this unit. Only supervised or approved riders who are
capable of handling the mini bike are allowed to sit on and ride the unit.
DANGER
!
WARNING
!
WARNING
!
WARNING
!
DANGER
!

855-833-6483 OR EMAIL US AT [e-mail]
Use Safe Riding Pracces
• Do not jump, or aempt stunts, with your MM-E250.
• Hold onto handle bars at all mes.
• Never wear earphones or operate a cell-phone or video game while riding.
• Keep all loose arcles of clothing (laces, pants, sleeves, scarfs, etc.) away from
moving parts such as the drive sprocket and chain.
• Never hitch a ride from another gas-powered or electric vehicle.
• Do not ride the MM-E250 near pools, or in wet weather and do not immerse mini
bike in water. Water will damage the electric components and void your warranty.
• Always operate at a safe speed. The bike is set on the “slow” speed, but if you want
to increase speed, see secon “Check Speed Switch” to change to higher speed.
• Always use common sense when faced with problems. If there is any doubt about a
situaon or problem with your unit, do not operate further and call our customer
service line – 855-863-6483.
Improper accessories or modicaons can cause a crash in which riders
can be seriously hurt or killed. Follow all instrucons in this owner’s manual regarding
modicaons and accessories.
5
Operang Controls and Component Locaons
When you ride your mini bike, you need to operate the throle, brakes, and other controls
without stopping to look at them. Please read this secon carefully before you ride your
mini bike. This secon of the manual will describe the funcon, locaon, and operaon of
all the basic controls of your mini bike.
Brake Lever
Foot Peg
Chain Tensioners
(both sides of mini mike)
Throle
DANGER
!
WARNING
!
Important Safety Informaon
ON/OFF Switch
Baery
Charging
Port
Baery
Cover
Kick
Stand

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
Operang Controls
ON/OFF Switch
The ON/OFF switch is used to control power to the motor.
When the switch is in the “OFF” posion, no power is
supplied to the motor. To ride the mini bike, ip the switch
up. This is the “ON” posion. To shut o the bike, close the
latch or move the switch down to the “OFF” posion.
Throle
The throle controls the speed of the motor. To increase
emotor speed, slowly twist the throle grip toward you. To
reduce motor speed, twist the throle grip away from you.
The throle is spring loaded and will return to the closed
posion (motor idle) when you remove your hand.
Because this is an electric product, small
movements in the throle produce an instant response in
the motor. Do not suddenly twist throle or you risk severe
injury.
Rear Brake
The brake lever is used to apply the brake to the rear wheel
and will slow or stop the mini bike. When you pull back on
the lever, the brake cable pulls the caliper on the brake disc.
The amount of force that you use when pulling the brake
lever will determine how much braking power is applied. To
release the rear brake, release the brake lever.
Kick Stand
The kick stand is used to support the mini bike when it is
parked. To operate, use your foot to lower the stand. Always
raise the stand before riding the mini bike.
6
WARNING
!
Switch

855-833-6483 OR EMAIL US AT [e-mail]
Operang Controls
Brake Mechanism
The MM-E250 mini bike is equipped with a rear disc brake.
It provides power to safely bring the mini bike to a stop.
Refer to the Basic Maintenance Procedures secon for brake
adjustment instrucons.
Chain Tensioner
Chain tension is maintained and adjusted by the bolts on both
sides of the rear wheel. The adjustment screw will increase or
decrease the slack on the chain. Please see Basic Maintenance
Procedures to understand how to determine proper chain
tension and for instrucons on how to make adjustments to
maintain proper tension.
7
Brake
Caliper
Disk
Adjustment
Screw
Adjustment
Screw

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
8
YourMonsterMotoMM-E250isshippedwith
the handlebars NOT bolted on.
To aach the handlebars follow the steps below:
1. Aer unpacking your mini bike, place it on the kick stand on a
at level surface.
2. While sing on the bike, place the handle bars in the lower
clamp in a comfortable posion, being careful to center in the
clamps.
4. Replace upper clamps and bolts and ghten to 12 foot-lbs
with the allen wrench provided. Do not overghten.
2. Aaching the Handlebars
Top View
Handlebar Clamps
1. Locate All Accessories in Package Before Proceeding
- Owner’s Manual
- Tools (2 allen wrenches, 2 box end wrenches, 2 handlebar clamps & 4 bolts, screwdriver)
- Charger
Inial Set-Up
NOTICE The rst me you charge your baery it must be fully charged. While it will be
tempng to charge for a short amount of me to be able to ride the mini bike immediately,
failure to properly charge will severely shorten the run me as the baery ages and limit
the number of recharges the baery will take. Your mini bike will be ready to ride when the
indicator light on the charger turns GREEN.
1) Make sure the on/o switch is in the o (“down”) posion.
2) Locate the charger and nd the baery port on the right
front side of the mini bike.
3) Remove the plasc protecve cap, align the notch on
the charger and port and insert charger.
4) Plug the other end of the charger into a standard 110-volt
household outlet.
5) Connue to charge unl GREEN light on charger appears.
6) Unplug charger from wall, disconnect charger from port
and install port cover once charging is complete.
7) Conduct pre-ride inspecon and begin having fun!
Remove charger from bike once GREEN light appears on charger. Extending
charging me will NOT extend operang me.
THE UNIT WILL NOT TURN ON WHILE THE CHARGER IS PLUGGED INTO THE
CHARGING PORT! Disconnect the charger from the port before aempng to ride the bike.
3. Charge the Baery
WARNING
!
Bolts
CAUTION
!
Charging
Port

855-833-6483 OR EMAIL US AT [e-mail]
9
Before each ride, go through the following checklist to ensure your MM-E250 is safe and you
are ready. Make sure the rider fully understands the contents of the owner’s manual and is
capable of safely riding.
1) INSPECT FOR LOOSE PARTS
Check your MM-E250 for any loose plasc pieces or fasteners. If you nd any, please
correct the issue and connue your inspecon. If you hear rales or other sounds you
cannot locate, do not operate the unit and contact Monster Moto customer service
at 855-833-6483 or your local Monster Moto authorized service center.
2) INSPECT FRAME, FORKS AND HANDLEBARS
Check for cracks in the metal, bent forks or frame, disconnected wires or other
abnormal issues. These can result from abusive riding and can cause unsafe riding
condions if not corrected.
3) CHECK TIRE PRESSURE
Your res should be properly inated. Underinated res can limit the handling
ability of the bike while overinated res can suddenly burst or create a rough ride.
4) CHECK PROPER BRAKE FUNCTION
Squeeze your brake handle to make sure it applies pressure to the rear wheel brake
disc. If it does not properly grab the disc, please adjust brakes and try again. The brake
handle should return to original posion aer handle is squeezed.
5) CHECK THE CHARGER
Be sure to disconnect the charger from the baery port prior to operang the mini
bike. The unit will not run at all if the charger is sll plugged into the port on the
mini bike.
6) SAFETY GEAR
Be sure to have the proper Department Of Transportaon cered helmet. Goggles,
knees and elbow pads, and long pants and shirt are also recommended to ensure
maximum protecon. Always wear shoes and ensure that your laces are ed and secured
way from the mini bike wheels, drive sprocket and chain. Never ride barefooted or with
sandals.
Pre-Ride Check List

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
Basic Operaon
Aer you have conducted your pre-ride checklist, you are now ready to ride. There are a few
simple things you will need to know to enjoy your electric mini bike.
NOTICE If the charger is sll plugged into the
charging port on the mini bike, IT WILL NOT RUN.
Unplug the charger from the charger port and replace
the port cap. Unplug the charger from the wall outlet
and store in a safe place unl next use.
This switch allows the parent to control whether the
unit will operate at the slow speed (Max Speed: 6.8
MPH) or fast speed (Max Speed: 13 MPH)
First, make sure the power switch is in the “o”
posion. Next, remove the plasc baery cover by
unscrewing the front and back screws. Remove the
cover and set aside.
Locate switch below the baery box and set to desired
speed ( “0” = Fast; “I” = “Slow”).
Reinstall the baery cover.
Unplug Charger
Check Speed Switch
10
Charging
Port
“0” = FAST “1” = SLOW
Front Screw
Rear Screw

855-833-6483 OR EMAIL US AT [e-mail]
Basic Operaon
Li up the protecve cover on the tank and move the
switch into the “ON” posion.
This secon will cover basic braking technique for your mini bike. To slow or stop the
mini bike, squeeze the brake lever rmly and smoothly. Gradually increase your braking
pressure as you feel it is needed. When you come to a stop, put your foot down to balance
the mini bike.
Generally, reduce your speed and complete your braking before you begin a turn. Avoid
braking or closing the throle quickly while turning. Either of these acons may cause one
or both of the wheels to slip. Any wheel slip will reduce your control over the mini bike and
could cause a crash.
Rapid acceleraon, braking, or turning can cause you to lose control of the
mini bike.
Turn On the Power
Braking
When you want to stop, release the throle lever
to stop supplying power to the motor. Increase the
brake force unl the unit comes to a stop on a at
surface. Place both feet rmly on the ground to bal-
ance the bike and extend the kick stand. Gently lean
over the bike unl it rests safely on the kick stand and
dismount.
Parking
Aer every ride, stop to inspect the bike for loose parts, wires and fasteners. If the bike
was making unusual noise or sounds during the ride, trouble shoot the problem and x
before the mini bike is ridden again. If you have any quesons, contact our customer service
team (855-833-6483) or go online (www.monstermoto.com) to look at our library of service
videos or to read our FAQs.
Post-Ride Inspecon
11
WARNING
!

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
Basic Maintenance
Your electric-powered MM-E250 is a relavely low maintenance product because it uses
baeries and an electric motor instead of a gas-powered engine. But, there is sll basic
maintenance required to keep your mini bike operang smoothly. Each maintenance item
requires basic tools and mechanical aptude. DO NOT aempt any of these adjustments if
you do not feel comfortable.
You can visit our website to see our library of service videos which show step-by-step
instrucons for these maintenance procedures. You will also be able to look at our FAQs for
answers to other quesons. You can also call our trained customer service sta (855-883-
6483) and they will be able to answer any quesons you may sll have.
You can increase or decrease the pressure on your
mini bike brakes with the adjuster on the brake lever.
Release the lock nut and turn the adjuster ¼ - ½ turn
unl you achieve the correct pressure on your brake.
Tighten up lock nut when nished. (See Fig 1)
If your brakes donot work properly aer adjusng on
the brake lever, you will need to adjust the cable on
the caliper on the rear wheel. (See Fig 2)
Loosen the cable nut securing the brake cable to the
caliper. Slide the caliper arm up the cable unl it stop
and then back o about ½”. Reghten the lock nut and
try your brakes again.
1) Adjusng the Brakes
12
Adjusng
Nut
Adjusng
Nut
Caliper
Arm
Cable
Fig 1
Fig 2

855-833-6483 OR EMAIL US AT [e-mail]
Basic Maintenance
The service life of your drive chain will depend on several factors including proper lubricaon,
adjustment, and riding style. Poor maintenance will cause premature wear and/or damage
to the drive chain and sprockets.
Before you service your drive chain, be sure you are parked on a level surface and the ON/
OFF switch is turned “OFF”. As an addional pre-cauon, disconnect the posive lead on the
baeries to ensure there will be no power to the motor.
Failure to turn o power from the engine during this maintenance
procedure may result in accidental power being supplied to the engine. This many result in
ngers and hand being pinched or severed, or the mini bike moving and causing damage to
work area and owner.
2) Chain Inspecon and Adjustment
13
1) Aer you turn o power switch and disconnect
baery, reach inside chain guard to nd chain. Press
on chain mid-way between sprockets and determine
slack. Vercal movement should be between 1/4” and
3/8”.
2) If the chain needs to adjusted, locate the adjustment
bolts on either side of the rear wheel.
3) Adjust both sides equally and then retest chain
tension. Connue process unl you get the correct
slack.
If there is not enough slack in your
chain, it will result in excessive wear on the chain,
sprockets and bearings. Be careful not to overghten!
4) Reconnect baery and conduct pre-ride inspecon
to ride mini bike.
NOTE: You should replace the chain if the tensioner
is adjusted as far back as possible and there is sll
too much slack. This indicates excessive wear and the
chain is beyond it’s service limit.
WARNING
!
CAUTION
!
Le Side
Bolt
Right Side
Bolt

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
Basic Maintenance
Locate the valve stem on the res and check re
pressure. If it is not between 20 and 40 psi, add (or
deate) unl your pressure is correct.
For the rear re, access the valve stem between the
re and brake rotor. If you need to inate the re and
are not able to do so with a standard air chuck, use
and extender to access the valve stem.
3) Tire Pressure
Before you begin, make sure the
power switch is turned “OFF”. Failure to do so may
result in damage to the electrical circuit or a shock to
the person doing the repair.
The fuse for your MM-E250 is located inside the
baery box. To access it, carefully remove the
baery box by removing the screws on the front and
back of baery box.
Next, nd the fuse which is located on the jumper
between the two baeries. (See Fig 3)
Remove old fuse and replace with 30 Amp
automove fuse. (See Fig 4)
Replace fuse cover. Reinstall baery cover.
4) Fuse Replacement
WARNING
!
14
Valve
Stem
Fuse
Fig 3 Fig 4
Front Screw
Rear Screw

855-833-6483 OR EMAIL US AT [e-mail]
Basic Maintenance
Over me, your baery will lose its ability to hold a
charge. When this happens, you will need to install
new baeries.
Before you begin, make sure the
power switch is turned “OFF”. Failure to do so may
result in damage to the electrical circuit or a shock to
the person doing the repair.
Aer you have ensured the power switch is o,
remove the baery box per the instrucons in “Fuse
Replacement.”
Remove the rubber strap holding the baeries in
place and parally slide the baeries out to expose
the wiring. Note: You may need to move the black
wire bundle on the side of the baeries to slide them
out. (Fig 1)
Next, disconnect the middle terminals (one red, one
black) and remove the baeries from the baery box.
Disconnect the jumper cable from both baeries.
Take your new baeries and place them side by side
and connect the fuse as shown in Fig 2. Carefully
slide the baeries back into the baery box.
Reconnect the leads from the bike to the baery.
Make sure the red lead is connected to the posive
“+” terminal and the black lead is connected to the
negave “-“ terminal. (Fig 3)
Baery Replacement
You will need to make sure the connecons to the baery are done correctly.
- The posive terminal on the baery will need to be connected to the RED lead.
- The Negave terminal on the baery will need to be connected to the BLACK lead.
- Failure to properly connect baeries can result in serious injury to the rider or severe
damage to the electrical components of the mini bike.
Push the baeries back into the box and secure them with the rubber strap. Connect the
charger to the bike and charge unl the GREEN light on the charger is displayed
Only use the recommended baery charger. Failure to do so may result in
overheang of the baeries which can result in an explosion or create permanent damage
resulng in shorter baery life.
WARNING
!
WARNING
!
WARNING
!
15
Fig 1
Fig 2
Fig 3
Black Lead
Red Lead

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
16
Troubleshoong
1. Check the Baery Charge - Turn unit on and look at “gauge” on throle to see if bike is charged.
Is it fully charged?
No - Charge the baery unl the green light appears on the charger. If this is the rst me to
charge, it may take up to 8 hours to charge completely. If it’s been charged before, it could
take up to 6 hours.
Yes - Go to Step 2.
2. Check the fuse (Located in the black fuse holder in the baery box)
Is the fuse blown?
No - Go to Step 3
Yes - Replace the fuse by following the instrucons on page 14. If it connues to blow, see your
Monster Moto authorized service center to have your bike properly diagnosed and serviced.
3. Check the Charger Plug
Is it plugged into the mini bike?
No - See step 3.
Yes - The MM-E250 will not run when the charger is in the charging port. Disconnect and try again.
4. Check the Baery Connecons
Are all connecons ght?
No - Tighten all connecons as needed.
Yes - See your Monster Moto authorized service center to have your mini bike properly diagnosed
and serviced.
Does Not Run or Runs Occassionally
Bike Was Running But Stopped Abruptly
1. Check the fuse (Located in black rubber fuse holder in baery case)
Is it blown?
No - See Step 2
Yes - Allow the motor to cool o for 20 minutes and then replace the fuse following the instrucons
on page 14. If it connues to blow, see your Monster Moto authorized service center to have
your bike properly diagnosed and serviced.
2. Check the Power Switch
Is it visibly damaged?
No - See your Monster Moto dealer to have your mini bike properly diagnosed and serviced.
Yes - See your Monster Moto authorized service centerto have your mini bike serviced. (Or: Visit
our online store at monstermoto.com or call 855-833-6483 to order replacement parts or for
technical support.)

855-833-6483 OR EMAIL US AT [e-mail]
17
Troubleshoong
Short Run Time (15 minutes or less)
1. Check the Baery - Turn unit “ON” and look at the “gauge” on the throle to see if bike is charged.
Is it charged?
No - Charge the baery unl the GREEN light appears on the charger. If baery will not accept full
charge, it must be replaced. Visit our online store at monstermoto.com or call 855-833-6483
to order replacement parts or for technical support.
Yes - See Step 2
2. Check the Tires
Are they fully inated?
No - Inate res to 20-40 psi per instrucons on page 14.
Yes - See Step 3
3. Check the Brake
Is it adjusted properly?
No - Adjust the brake per instrucons on page 12.
Yes - See your Monster Moto authorized service center to have your mini bike properly diagnosed
and serviced. (Or: Visit our online store at monstermoto.com or call 855-833-6483 to order
replacement parts or for technical support.)
Bike Runs Poorly
1. Check for Overloading
Is the total load under 100 lbs.?
No - Do not exceed 100 lbs. of rider weight or aempt to carry passengers.
Yes - See Step 2
2. Review the Terrain
Is it too challenging?
No - See Step 3
Yes - Use only on solid, dry, at surfaces free of gravel and debris.
3. Check the Tires
Are they fully inated?
No - Inate res to 20-40 psi per instrucons on page 14.
Yes - See Step 4
4. Check the Brake
Is it adjusted properly?
No - Adjust the brake per instrucons on page 12.
Yes - See your Monster Moto authorized service center to have your mini bike serviced. (Or: Visit
our online store at monstermoto.com or call 855-833-6483 to order replacement parts or for
technical support.)
Charger Gets Warm When Charging
No acon is required. The Charger will generate a small amount of heat as the baery is charging.

855-833-6483 OR EMAIL US AT [e-mail]
PROBLEMS? DO NOT RETURN TO STORE! CALL US!
18
1. Check the throle Make sure when it is released it goes back to original posion.
Does the throle go back to original posion and cut power to the motor?
No - Check between the throle and handle for any debris lodged which prohibits the throle
from returning to original posion. Remove debris and check again. If problem connues
or you cannot nd any debris, see your nearest Monster Moto authorized service centerr to
have your bike serviced.
Yes - Go to Step 2
2. Check the Brake
Is it adjusted properly?
No - Adjust the brake per instrucons on page 12.
Yes - See your Monster Moto authorized service center to have your mini bike serviced. (Or: Visit
our online store at monstermoto.com or call 855-833-6483 to order replacement parts or for
technical support.)
Mini Bike Will Not Stop Properly
Grinding or Squeaking Noise While Bike is Moving
1. Check the Chain Tension
Is it adjusted properly?
No - Adjust the tension per instrucon on page 13.
Yes - See Step 2
2. Check the Chain Lubricaon
Is the chain adequately lubricated?
No - Lubricate the chain per instrucons on page 13.
Yes - See your Monster Moto authorized service center to have your mini bike serviced. (Or: Visit
our online store at monstermoto.com or call 855-833-6483 to order replacement parts or for
technical support.)
Troubleshoong
Bike Runs Fine but Slow
1. Check the Safety Speed Switch (The switch is located inside the baery case, under the baery)
Is it set at “I”?
No - Turn Safety Speed Switch from “I” (slow speed 6.8 mph) to “O” for fast speed (13mph) per
instrucons on page 10.
Yes - See your Monster Moto authorized service center to have your mini bike serviced. (Or: Visit
our online store at monstermoto.com or call 855-833-6483 to order replacement parts or for
technical support.)