Monte Carlo Fan Company 3MO52 O-V1 Series Instruction manual

Owner’s Guide and Installation Manual
Attach sales receipt to this card and retain as your proof of purchase
DATE OF PURCHASE:
MODEL NUMBER:
RETAILER NAME:
RETAILER ADDRESS:
To register your fixture, please visit our website www.montecarlofans.com
3MO52XXO-V1 / 3MTR38XXO-V1 Series Fans
cETL Model umber of 3MO52XXO-V1: 3MOR52
cETL Model umber of 3MTR38XXO-V1: 3MTR38
Total fan weight with light it
3MO52XXO-V1: 8.5 kg/18.7 lbs
3MTR38XXO-V1: 7.3 kg/16.1 lbs

© 2011 Monte Carlo Fan Company 5/25/2013
2
WAR I G: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR I JURY TO PERSO S, OBSERVE THE FOLLOWI G
READ A D SAVE THESE I STRUCTIO S
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (A SI/ FPA 70-1999), including
fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the
outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and pushed carefully up
into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to prevent
power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the
trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
15.9 kg (35 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do ot Re-
move Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign
object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control part no. UC7067RC manufactured by Rhine Elec-
tronic Co., Ltd.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
ever place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufac-
turer’s guideline safety standards such as those published by the ational Fire Protection Association ( FPA), and the American Society for Heating, Refrigera-
tion and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
S o ie, IL 60077
www.montecarlofans.com
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.

© 2011 Monte Carlo Fan Company 5/25/2013
3
Before you begin installing the fan, Switch
power off at Service panel and lock service dis-
connecting means to prevent power from being
switched on accidentally. When the service dis-
connecting means cannot be locked, securely
fasten a prominent warning device, such as a
tag, to the service panel.
Before installing this fan make sure the outlet box is
properly installed to the house structure. To reduce
the risk of fire, electric shock, or personal injury,
mount to outlet box or supporting system acceptable
for fan support. (Mounting must support at least 35
lbs.)
Use metal outlet box suitable for fan support
(must support 35 lbs). Before attaching fan to
outlet box, ensure the outlet box is securley fas-
tened by at least two points to a structural ceil-
ing member ( a loose box will cause the fan to
wabble). se only the screws provided with
the outlet box.
3
21
Carefully turn the motor over so that
the upper housing is facing up. Re-
move the 3 screws holding the upper
housing. Save for later use.
5
Lift off the upper housing to reveal
the motor.
6
lace the blade ring holder over
the leadwires and safety cable.
lace the blade ring holder onto
the blades aligning the screw
holes from the blades and ring
holder.
7
Install the motor screws by tighten-
ing securely.
8
lace the rubber gasket on the yoke
by threading the leadwires and safety
cable through the rubber gasket
aligning the holes from the gasket
and yoke.
9
lace the fan body with the light fitter
pointing upward. Attache the 3 blades as
shown above. Tighten set screws securely
4

© 2011 Monte Carlo Fan Company 5/25/2013
4
Loosen set screw and then remove
cross pin from yoke for downrod
to slip into yoke. Keep the cross
pin for later use.
12
Re-place the upper motor housing onto
the fan motor. Be sure the holes are all
aligned.
Note: Align the hole on top housing la-
beled “REVERSE” with the reverse switch.
10
Tighten the screws removed from
step 5. Tighten securely.
11
lace the canopy over the downrod
as shown above.
13
Thread the leadwires and safety
cable through the downrod.
14
lace the downrod into the yoke
aligning the holes on downrod with
the holes on the yoke and then re-in-
stall the cross pin removed in step
12. Tighten securely.
15
Tighten the set screw on the yoke.
16
Set screw
Cross pin
Reverse switch
Reverse switch
For Canadian installation and for USA fan and light
kit combinations over 35 lbs, in both flush and
downrod modes the safety cable must be installed
into the house structure beams using 3” lag
screws, washers and lock washers provided. Make
sure that when the safety cable is fully extended
the lead wires are longer than the cable and no
stress is placed on the lead wires.
Note:If Installing The Secondary Support Safety
Cable in the U.S., Do Not Remove Knockouts In
The Outlet Box.
18 Safety cable installation
Safety Cable
Lag Screw
safety
cable
3” lag
screw
lock
washer
washer
Hang the assembled fan from the
mounting bracket. Be sure to turn
the fan to lock the slot/tab from
the fan and mounting bracket in
place.
17
Tab
Slot

© 2011 Monte Carlo Fan Company 5/25/2013
5
Slide remote receiver into mounting
bracket.
21
Make wiring connections as indicated above.
White from fan to white from remote marked
N. Blue from fan to blue from remote marked
light. Black from fan to Red from remote
marked L. White from house to white from re-
mote marked AC N . Black from house to
Black from remote marked AC L. Connect all
green ground wires to Ground wire from
House.
19
white
Red
Set dip switches on the Remote Transmitter and Remote
Receiver to the same settings. This must be done so the
units will communcate properly. If you have other fans
you can set to control from one transmitter by setting both
receivers the same as the transmitter. If you have more
than one fan with remote. You can set the dip switches to
different positiosns to have seperate control.
Remote Transmitter Dip swtiches
Remote Receiver Dip switches
20
Make wire connections to power source using wire nuts
provided. Make sure that no filiments are outside of
the wirenut. After making the wire connections, the
wires should be spread apart with the grounded con-
ductor and the equipment-grounding conductor on one
side of the outlet box and ungrounded conductor on the
other side of the outlet box.
22
Attach the glass aligning the dimples
from the glass and twist to lock into
place.
25
Remove cover by snaping off from top or bot-
tom. Remove battery cover. Install 12V battery
into wall remote. Duracell MN21 / Eveready A23
/ G 23A all 12V.Attach cover of remote by plac-
ing over buttons and snap the battery cover in
place.
lace face plate over battery compartment and
buttons. lace remote over 2 pins on front
cover. Attach cover of remote by placing over 4
pins and snaping into place.
27
26 HAND HELD INSTALL
Lift the canopy up and twist to lock
into place. Tighten the screws se-
curely.
23
WARNING: Over lamping the fan will
result in the fan lights shutting down until
the proper wattage of bulbs are
installed. Reset the lights by turning off
the wall switch, breaker,or by remote. Re-
place bulbs with the correct wattage bulbs,
turn the power on.
24

© 2011 Monte Carlo Fan Company 5/25/2013
6
Reverse function for this fan is a
switch on top housing of the fan
body. Turn fan off and flip switch this
will reverse the direction of the
blades.
30
Install wall control unit to outlet box
using machine screws provided.
28
Attach front cover to wall control
with screws provided. Snap battery
cover in place.
29
WALL MOUNT INSTALL
Reverse switch
Remote Control Transmitter Features:
FAN SPEED Depress “1 dot” for low speed, “2 dots” for medium or “3 dots” for
high. To turn fan off press square”.
LIGHT DIMMER To turn light on, press light dimmer once quickly. To turn off
press once quickly while light is on. To dim light hold down button “light dimmer”.
The light will cycle from bright to dim to bright until button is released. Light will
maintain last setting if turned off.
HIGH S EED
MEDIUM S EED
LOW S EED
FAN OFF SETTING
(Turns fan off only)
LIGHT ON/OFF SET-
TING AND DIMMER
( ress and hold to
dim light infinitely)
LED LIGHT

© 2011 Monte Carlo Fan Company 5/25/2013
7
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Check to make sure the dip switches from transmitter and receiver are set on the same frequency.
CA TION: Make sure main power is turned off.
4.Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when
switch is in the middle.
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each other or
against the interior wall of the switch housing.
CA TION: Make sure main power is turned off before entering switch housing.
4.Some fan motors are sensitive to signals from Solid State variable speed controls.
DO NOT SE a Solid State variable speed control.
5.Allow "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this
period.
1.Make sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4.Make sure that canopy and mounting bracket are tightened securely to ceiling junction box and
junction box is mounted firmly to ceiling joist.
5.Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting
a point on the ceiling above the tip of one of the blades. Measure this distance from blade tip to
ceilng. Keeping measure within 1/8", rotate the fan until the next blade is positioned for measure-
ment. Repeat for each blade. If all blade levels are not equal, you can adjust blade levels by the fol-
lowing procedure. To adjust a blade tip down, insert a washer (not supplied) between the blade and
blade holder at the screw closest to the motor. To adjust a blade tip up, insert washer (not supplied)
between the blade and blade holder at the two screws farthest from the motor. Reverse the position
of the washer if blades mount from top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute
the weight and possibly result in smoother operation.
1.Check blue wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
CA TION: Make sure main power is turned off before entering switch housing or canopy.
WARNING: Over lamping the fan will result in the fan lights shutting down until the
proper wattage of bulbs are installed. Reset the lights by turning off the wall switch,
breaker,or by remote. Replace bulbs with the correct wattage bulbs, turn the power on.
2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
TROUBLE SHOOTING
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In
some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble
Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty in installation, please call our Cus-
tomer Service Center at the
number printed on your parts list insert sheet.
Warning: Before servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot
be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.

Dec.2011 new format
Jan.2011 Update customer service phone number Ma .2013
Update for CUL regulation
Feb.2018 change to cETL, change listed model number
May.2019 LED