montpellier MLM308BG User manual

Refrigerator
MLM308BG
Instructions for Use

GUIDELINES CONCERNING THE SAFETY OF USE
1
GENERAL INFORMATION
3
DESCRIPTION OF THE APPLIANCE, BASIC PARTS
4
INSTALLATION AND OPERATING CONDITIONS OF THE
APPLIANCE
5
ELECTRONIC CONTROL PANEL DESCRIPTION. TEMPERATURE
REGULATION
7
USING THE REFRIGERATOR EFFICIENTLY
8
DEFROSTING
9
CLEANING AND CARE
9
TROUBLE-SHOOTING
10
TRANSPORT
11
ENVIRONMENTAL PROTECTION
11
PRODUCT FICHE
13

1
GUIDELINES CONCERNING THE SAFETY OF USE
Some provisions in this user manual are unified for refrigerating products of
different types (for a refrigerator, refrigerator-freezer or freezer). CAREFULLY
READ THE INSTRUCTION MANUAL. The Manufacturer shall not be held liable
for damage arising from the failure to observe the instructions contained in this
manual. Keep this manual for future reference, or to pass it over to the next
user.
–Do not cover the ventilation holes at the top and on the sides of the appliance.
–Do not use any mechanical means or electrical devices to hasten the thawing
process when cleaning the freezer compartment.
–Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
–If the supply cord is damaged it must be replaced by the manufacturer,
manufacturer service agent or a similarly qualified person, in order to avoid a
hazard.
–Disposal of the appliance should be according to national rules.
–Do not damage the appliance refrigeration system. It contains the refrigerant
gas R600a. If the refrigeration system is damaged:
•Do not use any open flame.
•Avoid sparks―do not turn on any electrical appliances or lighting
fixtures.
•Immediately ventilate the room.
–Air the room in which the appliance is placed for a few minutes (the size of the
room for a product containing isobuthane / R600a must be at least 4 m3) to
avoid damage to the cooling system.
–Do not allow children to play with the appliance or to plug it in or unplug from
the electricity supply socket. Do not allow children to play with the packaging
material from the appliance.
–This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
–Cleaning and user maintenance shall not be made by children without
supervision.

2
The appliance should only be connected to an earthed socket installed in
accordance with the regulations. Make sure that the supply voltage
corresponds with the voltage marked on the rating label. This product
complies with all binding CE labelling directives. The earthed electrical
socket by which the appliance is connected to the mains should be in an
accessible place. It is a legal requirement that the appliance is properly
earthed. The manufacturer will not be held liable for any damage or injury
which may result from the failure to fulfil this requirement.
–TO AVOID THE EXPOSURE TO DANGER, ALWAYS HAVE FAULTY CABLE
BE REPLACED ONLY BY THE MANUFACTURER, BY OUR CUSTOMER
SERVICE OR BY QUALIFIED PERSON AND WITH A CABLE OF THE SAME
TYPE.
–It is forbidden to readjust or modify any parts of the unit. It is crucial not to
damage the capillary tube visible in the compressor recess. The tube may not
be bent, straightened or wound. If the capillary tube is damaged by the user
the guarantee will be void.
–It is forbidden to use a technically damaged appliance.
–The appliance can’t be disposed of by burning.
–Do not store beverages in bottles and cans, especially carbonated beverages,
in the freezer chamber. The cans and the bottles may explode.
–Do not put frozen products, taken out directly from the freezer (lollies, ice
cubes, etc.) into your mouth; their low temperature may cause severe frost-
bite.
–The appliance should be used only for freezing and storing foodstuffs.
–This appliance is not designed for the storage of explosive substances such as
aerosol cans with a flammable propellant.
–It is prohibited to store petrol and other flammable liquids near the appliance.
–The appliance operates properly at the ambient temperature (see product
fiche). Do not use it in the cellar, unheated summer cottage during autumn and
winter.
–Pull the plug out from the mains socket before each maintenance activity. Do
not pull on the cord, but hold the body of the plug instead.
–When performing activities, such as cleaning, maintenance or moving, the
appliance must be completely disconnected from power supply (by pulling the
plug out from the socket)
–If the appliance is unplugged (for cleaning, moving to another place, etc.), it
may be repeatedly switched ON AFTER 15 MIN.

3
–Do not place any switched on electrical devices (such as microwave ovens,
hair dryers, irons, electric kettles or other electrical devices) on top of the
appliance because this may cause ignition of plastic parts.
–Do not place any dishes with liquids on top of the appliance and do not keep
flowers in vases or other liquid-filled vessels on the appliance.
–Do not climb on or sit on the appliance, do not lean on or hang on the
appliance doors and do not allow children to do this.
DO NOT TRY REPAIR THE APPLIANCE ON YOUR OWN. ALWAYS
CONTACT AN AUTHORIZED TECHNICIAN. TO AVOID THE
EXPOSURE TO DANGER, ALWAYS HAVE FAULTY CABLE BE
REPLACED ONLY BY THE MANUFACTURER, BY OUR CUSTOMER
SERVICE OR BY QUALIFIED PERSON WHIT A CABLE OF SAME
TYPE.
ATTENTION! DO NOT REMOVE THE COVER OF THE LIGHT EMITTING
DIODE (LED) LUMINAIRE! If the cooling appliance is equipped with light
emitting diode (LED) luminaire and the lighting is not functioning, please contact
a maintenance technician to have it replaced. THE LUMINAIRE CAN BE
REPLACED ONLY BY A MAINTENANCE TECHNICIAN!
GENERAL INFORMATION
The appliance is a refrigerator intended for a short-term storage of chilled products.
THE APPLIANCE IS ECOLOGICALLY CLEAN, CONTAINING NO MATERIALS HARMFUL TO
THE OZONE LAYER: the refrigerant used is R600a, the foaming agent used for the
appliance insulation is cyclopentane C5H10.
THE MANUFACTURER GUARANTEES RELIABLE OPERATION OF THE REFRIGERATOR
WHEN THE RELATIVE AIR HUMIDITY NOT GREATER THAN 70 PER CENT AND THE
AMBIENT TEMPERATURE IS:
+16 TO +32 DEGREES CELSIUS (Climate class N);
+16 TO +38 DEGREES CELSIUS (Climate class ST).
+16 TO +43 DEGREES CELSIUS (Climate class T).

4
DESCRIPTION OF THE APPLIANCE, BASIC PARTS

The pull-out drawer 5 moves on roller
bearings 17. The drawer can be
removed by pulling it out and lifting it
off the rails.
1
Electronic control display
7
Fruit and vegetable box
2
On / off switch for interior light
8
Door trays
3
Shelf for bottles
9
Egg tray
4
Adjustable height shelves
10
Condenser
5
Pull-out drawer
11
Thaw water drip tray
6
Glass shelf
12
Compresor

5
INSTALLATION AND OPERATING CONDITIONS OF
THE APPLIANCE
Installation before using the appliance for the first time
It is recommended to prepare the appliance for operation with a helper.
•Remove package. Lift the appliance away from foamed polystyrene base. Tear off
adhesive tapes.
•When positioning the appliance in chosen location, it will move more easily into
position if you lift the front a little and incline it backward, allowing it to roll on its
casters. Moving or positioning the appliance do not tilt it by more than 40° from the
vertical position.
When placing, moving, lifting the appliance, do not hold the door
handles, do not pull the condenser at the rear part of the refrigerator
and do not touch the compressor unit.
•Remove all red-coloured parts from the
shelves. Tear away the adhesive tapes from
the door trays –they are intended only for
the transport of the appliance.
NOTE. When you open the freezer
compartment door a little red packing detail will fall out –IT IS FOR
TRANSPORTATION PURPOSES ONLY.
•Take two supports 1from the bag and insert
them into the guides 2at the top back part of the
appliance (see picture).
If the appliance is brought in from the cold (temperature is not higher than +12
°C), you should wait for two hours before connecting it to the mains.
The appliance should not be connected to the mains until all packing and
transport materials aren’t removed. Suitably dispose the packaging material.
Connection to the mains
•This appliance should be connected to AC 220-240V 50Hz supply socket. The socket
must be fitted properly, and must be supplied with an earthling conduit and a 10A
fuse. It is a legal requirement that the appliance is properly earthed. The
manufacturer will not be held liable for any damage or injury which may result from
the failure to fulfil this requirement.
•Do not use adapters, multiple sockets and two-wire extension leads. If it is necessary
to use the extension lead, it must be equipped with a protection ring and a single
socket and must have a VDE/GS safety certificate.
•If an extension lead is used (with a protection ring and safety certificate), its socket
must be located at a safe distance, away from the sinks, and must not be in a place
where it could be flooded by water or waste water.
•When positioning the appliance, be careful that the electrical cord isn’t squeezed in
order to avoid its damage. Do not store heavy objects such as cooling devices,

6
furniture or other domestic devices next the appliance in such a way that they could
squeeze and damage the electrical cord. This can cause a short circuit and a fire.
•Make sure that the plug of the electrical cord is not squeezed by the back wall of the
appliance or otherwise damaged. A damaged plug can be the cause of a fire!
Positioning
•Place the appliance in a dry, well ventilated room.
WARNING! The appliance should not be operated in an unheated room
or porch. Place the appliance away from heat sources such as kitchen
stove/oven, radiators, or direct sunlight.
The rear wall of the refrigerator, in particular, the condenser and other elements of the
cooling system must not contact other elements, which may damage them, (e.g. central
heating pipes and the water supply pipes).
WARNING! The appliance must not touch any pipes for heating, gas or
water supply, or any other electrical devices.
Minimum distances from the heat sources:
- from the electric gas and other ovens - 30 mm,
- from oil or coal fired ovens - 300 mm,
- from built-in ovens - 50 mm
If there is no possibility of ensuring the above- mentioned distances, provide an
appropriate insulation board.
•Do not cover the ventilation holes at the top of the appliances –
it must be a good air circulation around the appliance. There
should be a gap of at least 10 cm between the top of the
appliance body and any furniture that may be above it (see fig.).
If this requirement is not followed, the appliance consumes more
electrical energy and its compressor may overheat. 
•The appliance must stand on a level surface and must not touch
the wall. If necessary, regulate the height of the appliance by
adjusting the levelling feet: by turning them clockwise –the
front of the appliance rises, by turning them counter clockwise –
it comes down. If the appliance
is tilted slightly backward –the
doors will close by themselves.
•◄If the appliance is placed in a
corner, a gap must be left between the appliance
body and the wall so that the freezer compartment
door can be opened enough to pull out the frozen
product drawer (see picture).

7
ELECTRONIC CONTROL PANEL DESCRIPTION.
TEMPERATURE REGULATION.
When connecting the device to the mains for the first time, the blue temperature
indicating segment lights up at +5: factory temperature setting +5 °C, but you can
select the preferred temperature according to your needs.
The appliance features and temperature are controlled with touch (sensory) buttons.
When the desired function is on, the function symbol is lit in a white colour
and when it is turned off, the symbol becomes grey.

1. Temperature adjustment button is marked with the °C symbol. You can set
the temperature of the refrigerator compartment between +1 °C and +9 °C.
Temperature setting in the refrigerator
Activate temperature button 1: tap and hold until the temperature indicating segment
starts to flash in blue (active). Then release button 1and tap repeatedly until the
required temperature segment is blue (activated). One tap changes the temperature by
one position.
The temperature setting operates in a circle: for example, the active segment is at +5,
and if you want to set +1 °C after activation you have to tap temperature button 1 3
times –until the temperature indicating segment at +1 turns blue.
Refrigerator compartment temperature is adjustable on a five-point scale:
+9 –highest temperature (lowest cooling).
+1 –lowest temperature (highest cooling).
NOTE. After power loss the device turns on automatically, saving the last user-set
temperature in the refrigerator compartment.
THE TEMPERATURE IN THE REFRIGERATOR COMPARTMENT MAY VARY
DEPENDING ON AMBIENT TEMPERATURE, THE AMOUNT OF FOODSTUFFS, THE
TEMPERATURE OF THE FOODSTUFFS, AND HOW OFTEN THE APPLIANCE
DOORS ARE OPENED AND CLOSED. Therefore we recommend:
•locate the appliance away from heat sources,
•do not put hot foodstuffs in the refrigerator –they must be cooled down to
room temperature,
•appliance door must not to be left open,

8
•the appliance door should not be open longer than it is necessary to take out or put in
foodstuffs
IF THE REFRIGERATOR DOOR IS OPEN MORE THAN 30 SECONDS an audible warning
signal sounds, and silenced when the door is closed.
If the room temperature is below +16 °C, we recommend that you set a lower
temperature with the temperature-selection button (1).
Cooling device on/off
SHUTDOWN. Tap and hold button 1until the three temperature indicative segments are
blue, and the light in the refrigerator compartment turns off. CAUTION! Voltage remains
turned on.
SWITCHING ON. Tap and hold button 1until the set temperature indication segment is
blue, and the refrigerator compartment lighting is on.
NOTE: after turning on the cooling device, the last temperature set by the user will be
saved.
2. Temperature indicator segments. The temperature set-point segment is
illuminated in blue (active), while the other temperature value segments are grey
(inactive).
3. The quick cooling function is activated by tapping button 3 marked with the
symbol. When the quick cooling function is on, the white segment in the centre of the
button is on.
The quick cooling function is recommended when you want to cool down quickly fresh
food products to +5 °C or when many food products are loaded into the refrigerator.
When the food products have been cooled to +5 °C, the quick cooling function turns off
automatically. If you do not want to wait until it has cooled down to the set
temperature, touch the button 3 of this function and turn the function off - the white
segment will become grey.
USING THE REFRIGERATOR EFFICIENTLY
Storage zones in the refrigerator
•Due to the natural circulation of the air in the appliance, there are different
temperature zones in the refrigerator chamber.
•Pre-packed vegetable and other fresh food with a label stating it should be kept at a
temperature of approx. +4 °C.
•The warmest area is in the top section of the door. Use this for storing butter and
cheese.
Food that should not be stored in a refrigerator.
Not all food is suitable for storing in the refrigerator, particularly:
- Fruit and vegetables which are sensitive to cold, such as bananas, avocado, papaya,
passion fruit, aubergines, peppers, tomatoes and cucumbers.
- Fruit which is not yet ripe
- Potatoes
•Do not keep prepared food and ready-to-cook (“heat and eat”) food in the same
container.

9
•Strictly observe the foodstuff validity time indicated by the manufacturer
on the product packaging.
•Store in an airtight container in the appliance any foodstuffs that have a strong odour
(e.g. fresh fish, pâté de foie gras goose liver pâté, and cheese).
•Frozen foodstuffs should be thawed in the refrigerator compartment. Food that thaws
slowly retains better flavour properties and spread cold will help to maintain the set
temperature in the refrigerator compartment.
THE TEMPERATURE IN THE REFRIGERATOR COMPARTMENT MAY VARY
DEPENDING ON AMBIENT TEMPERATURE, THE AMOUNT OF FOODSTUFFS, THE
TEMPERATURE OF THE FOODSTUFFS, AND HOW OFTEN THE APPLIANCE
DOORS ARE OPENED AND CLOSED. Therefore we recommend:
•locate the appliance away from heat sources,
•do not put hot foodstuffs in the refrigerator compartment –they must be
cooled down to room temperature,
•appliance door must not to be left open,
•the appliance door should not be open longer than it is necessary to take out or put in
foodstuffs.
DEFROSTING
THE REFRIGERATOR COMPARTMENT defrosts automatically. Drops of ice that form on
the back wall of the refrigerator compartment thaw during the time the compressor is
not working and the thaw water runs down the thaw water runoff channel to the tray
on top of the compressor (Fig. 1), where it evaporates.
CLEANING AND CARE
REGULARLY CLEAN THE APPLIANCE!
Note: before cleaning the cooling device and its rear compartment part,
the device must be disconnected from the mains by unplugging.
•Protect the appliance inner surfaces and plastic parts from fats, acids and sauces. In
case of accidental spills –immediately clean with warm soapy
water or dishwashing detergent. Wipe dry.
•Clean the appliance inner surfaces with warm soapy water.
Dishwashing detergent may also be used.
•Wipe dry inner and outer surfaces.
•Regularly clean the hermetic gaskets of the doors. Wipe dry.
•Regularly wash the trays and other accessories.
•◄REGULARLY CLEAN THE THAW WATER CHANNEL SPACE
WITH A SPECIAL CLEANER FOR THAT PURPOSE (see picture).
•At least once a year clean dust away from the back part of the
appliance body and the compressor. A soft brush, electrostatic
cloth or vacuum cleaner may be used for cleaning.
•DO NOT use detergents containing abrasive particles, acid, alcohol or benzene for
cleaning the appliance inner and outer surfaces. DO NOT use for cleaning cloths or
sponges that have coarse surfaces intended for scrubbing.

10
•IF THE APPLIANCE IS TO BE LEFT SWITCHED OFF FOR AN EXTENDED PERIOD,
LEAVE ITS DOORS OPEN.
Rem ar ks on t he ap pl ia nce o per at in g noi se . As the appliance
operates and goes through the freezing cycle, various noises will be emitted.
This is normal and is not a sign of any malfunction.
•As the refrigerant circulates around the refrigeration system, it causes sounds like
murmuring, bubbling, or rustling.
•Louder sounds like popping or clicking may be heard for a short time as the
refrigerator’s compressor switches on.
OPERATION PROBLEMS AND THEIR SOLUTIONS
(TROUBLESHOOTING). What if …
•The appliance is plugged in to the mains but it does not work. Check that your
house electricity supply installations are in order. Check that the plug is correctly
inserted into the electricity supply socket.
•Segment in centre of temperature adjustment button is red. Cooling device is
operating in emergency mode. Contact the refrigeration appliance’s maintenance and
repair company without delay.
•Temperature cannot be set, quick cooling function cannot be activated.
Close the refrigerator door, turn off the cooling device –disconnect the power supply
cord from the outlet, and wait 12 minutes. After the specified time, plug the power
cord back into the outlet and perform the required action: set the temperature or turn
on the quick cooling function.
•The noise has become louder. Check that the appliance is standing stable, on a
level place. To make it level, regulate the front feet. Check if the appliance is not
touching any furniture, and that no part of the refrigeration system at the back part of
the appliance body is touching the wall. Pull the appliance away from any furniture or
walls. Check that the cause of increased noise isn’t due to bottles, cans or dishes in
the appliance that might be touching each other.
•Water has appeared at the bottom of the refrigerator compartment. Check
whether a thaw water channel space isn’t blocked. Clean the thaw water channel
space with a cleaner intended for that purpose.
•Water has appeared on the tempered glass shelves. Food items or dishes in
the refrigeration compartment are touching the back wall of the compartment. Do not
let food items or dishes touch the back wall.
•Moisture dripping from under the glass shelves. If you placed many containers
with liquids on the shelf, moisture can condense and drip onto the shelf below. Move
some containers with liquids onto other shelves.
•Water has appeared under the appliance. The thaw water collection tray has
slipped off the compressor. Place the tray on top of the compressor.
•When the appliance door is opened, the rubber sealing gasket pulls out. The
gasket is smeared with sticky foodstuffs (fat, syrup). Clean the sealing gasket and the
groove for it with warm water containing soap or dishwashing detergent and wipe dry.
Put the rubber sealing gasket back into the place.
•High temperature in appliance, the compressor operation pauses are short.
Ascertain whether the appliance doors are shutting tightly, whether the door wasn’t

11
kept open longer than necessary when taking out or putting in foodstuffs or whether
a large amount of warm food was placed in the appliance.
The top of the appliance has condensation on it. The ambient relative air
humidity is above 70 %. Ventilate the room where the appliance stands and if possible
remove the cause of the humidity.
TRANSPORT
THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR ANY DAMAGE OF THE
APPLIANCE THAT RESULTS FROM NON-COMPLIANCE WITH THE INSTRUCTIONS
FOR TRANSPORTATION.
•The appliance should be transported in the vertical position.
•When being transported, the appliance should be protected from atmospheric
conditions (rain, snow, dampness).
•The appliance should be firmly secured in place while being transported, to avoid
slippage or any shocks in the transport vehicle.
•If the appliance was transported not vertically, it may be connected to the
mains after 4 hours at least. If this is not done, the appliance compressor
may fail.
ENVIRONMENTAL PROTECTION
Ozone layer protection
The refrigerants and foaming agents, which are 100% free of FCKW and FKW have
been used for manufacturing our product. Therefore we are helping to protect the
ozone layer and prevent the increase of greenhouse effects. Also, the innovative
technology and environmentally friendly insulation help in reducing energy
consumption.
Recycling of the packaging
Our packaging are made of environmentally friendly materials, which can be reused:
•The external packaging is made of cardboard/foil;
•The FCKW free shape of foamed polystyrene (PS);
•Polyethylene (PE) foils and bags.
ELIMINATION / DISPOSAL OF THE EQUIPMENT
If the appliance is no longer in use, cut the connecting cable off the used
equipment before its scrapping. Also, remove the appliance lock or render it
useless so that the appliance presents no danger to children while being
stored for disposal. This appliance is marked with a symbol of the crossed out
waste container in conformance with the European Directive 2002/96/EC. Such
marking informs that the equipment may not be kept together with other waste coming
from the household after the period of its use. The user is obliged to dispose of the
appliance at the waste collection point. The local waste collection points, shops and
communal units form an appropriate system enabling the disposal of the equipment.
Handling the used electrical and electronic equipment properly contributes to the
avoidance of consequences harmful to the human health and natural environment,
resulting from the presence of hazardous substances and improper storage and
processing of such equipment.

12
Manufacturer’s Declaration
The manufacturer hereby declares that this product meets the requirements of the
following European directives: Low Voltage Directive 2014/35/EC; Electromagnetic
Compatibility (EMC) Directive 2014/30/EC; ErP Directive 2009/125/EC and has
thus been marked with the symbol and been issued with a declaration of compliance
made available to market regulators.

13
PRODUCT FICHE
NOTE. The manufacturer reserves the right to make future changes to technical parameters and
specifications.
¹)
1 = Refrigerator with one or more fresh-food storage compartments,
2 = Refrigerator-cellar, Cellar and Wine storage appliances,
3 = Refrigerator-chiller and Refrigerator with a 0-star compartment,
4 = Refrigerator with a one-star compartment, 5 = Refrigerator with a two-star compartment,
6 = Refrigerator with a three-star compartment, 7 = Refrigerator-freezer,
8 = Upright freezer, 9 = Chest freezer, 10 = Multi-use and other refrigerating appliances
²)
A+++ (most efficient) to D (least efficient)
³)
Annual energy consumption (AE C ) in kWh per year, based on standard test results for 24 hours.
Actual energy consumption will depend on how the appliance is used and where it is located.
4)
1 One-star compartment with nominal temperature of -6°C
2 Two-star compartment with nominal temperature of -12°C
3 Three-star compartment with nominal temperature of -18°C
4 Food freezer compartment (four-star compartment) with nominal temperature of -18°C
⁵)
Climate class: This appliance is intended to be used at an ambient temperature between lowest and
highest temperature: SN = 10°C-32°C, N = 16°C-32°C, ST = 16°C-38°C, T = 16°C-43°C
Model
MLM308BG
Category ¹
1 - Refrigerator
Refrigerator net volume, L
308
Cold section net volume, L
-
Freezer net volume, L
-
Actual consumption will depend on how the appliance is used and where it is located
Energy efficiency class ²
A+
Annual energy consumption ³, kWh/year
138
Climate class 5
N-T
Frost-free system
-
Star marking of frozen-food storage compartments 4
-
Freezing capacity, kg / 24 h
-
Temperature rise time, h
-
Height / width / depth of product, cm
163 / 60 / 63
Noise level, dB(A) re1pW
41
Construction
Freestanding
Electrical Data: see in the product label

14
NGBSGCMO
2017-01-02