Morel Mps 4.400 User manual

MOREL PERFORMANCE

SERIES AMPLIFIERS

Owner’s Manual

MPS 4.400 |MPS 1.550 | MPS 5.950

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

We thank you for choosing Morel ampliers to complement your car audio system. The

new MPS ampliers were developed with the same passion and innovative philosophy

that is driving all of Morel’s product development. The MPS ampliers are musical,

dynamic, with clean, uncolored power that can drive speakers to their full sonic potential.

It is very important to carefully read this manual to ensure safe and optimal operation

of the amplier. We highly recommend to have a professional installer integrate the

amp into the sound system. There are many parameters that needs to be taken into

consideration when installing an amplier to safeguard that the car’s electrical system is

not compromised in any way and the sound system is tuned properly.

PRACTICE SAFE SOUND!

Studies have shown that continuous exposure to high sound pressure levels from high

power audio systems can lead to permanent hearing loss. Additionally, high volume levels

can obscure noises from outside your vehicle such as emergency vehicles and horns.

As a valued Morel customer, we urge you to use common sense and practice restraint in

the operation of this product.

Serial Number:

PACKAGE CONTENT

(1) MPS amplier

(1) 2mm hex wrench

(1) 2.5mm hex wrench

(1) 3mm hex wrench

(4) Mounting screws

(1) User manual

(2) Top panel replacement screws

AVAILABLE ACCESSORIES

MPS-R1 subwoofer remote level control (works with MPS 1.550 and MPS 5.950 only)

MPS-HL high-low level adaptor with 50-ohm load resistor

PRECAUTION

The MPS ampliers are designed to work with a 12V DC electrical system with negative

to ground. Use of this product in vehicles with positive ground and/or voltages other than

12V may result in damage to the product and/or vehicle and will void the warranty.

PLEASE MAKE SURE TO CAREFULLY READ AND UNDERSTAND

ALL INSTRUCTIONS PRIOR TO INSTALLATION

SERIAL NUMBER

Please take the time to enter the serial number in the space provided below.

The serial number can be found on the bottom panel of the amplier and on the amplier

packaging. This is required in the event that your amplier requires warranty service and

may be helpful in recovering your amplier in case of a theft. Be sure to store you this

manual in a safe location.

All Morel MPS ampliers comply with CE and EMC regulations.

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

MOUNTING THE AMPLIFIER

Choose a location for the amplier with ample ventilation for optimum cooling

performance. Be sure the amplier is mounted with at least 2-inches (50mm) of clearance

around the chassis, and never fully enclosure the amplier in a conned space without

active ventilation. It is strongly discouraged to mount the amplier upside down as this will

limit the heatsink’s ability to remove heat from the circuitry. Also avoid mounting in areas of

direct sunlight and in areas of high vibration, such as a subwoofer enclosure.

Proper mounting consists of the chassis being mounted with the base of the amplier

parallel with the oor or perpendicular to the oor with the ns of the heatsink facing

upward for eective cooling.

Your amplier should always be installed in a location that will remain free of moisture

and dirt, and in a manner that does not interfere with any of the electronics or safety gear

of the vehicle.

For safety purposes, be sure to take the time to properly mount the amplier using

suitable mounting hardware so the amplier does not come loose in the event of a

collision or unforeseen circumstance.

PLANNING AND INSTALLATION

For best results, determine the best conguration of your new amplier and plan

the wiring routes to ease installation and optimize performance.

IMPORTANT! Disconnect the vehicle’s primary ground terminal from the battery post

prior to commencing the installation.

Make sure the mounting location you chose for the amplier does not interfere

with any functions of the vehicle mechanics and/or electronic devices. Also, be aware

of the locations of the gas tank, wiring harnesses, fuel and brake lines, and other vital

components of the vehicle prior to drilling any holes in the vehicle’s chassis.

Select high quality signal cables and proper wire. It is highly recommended

to use 100% OFC (oxygen free copper) power and speaker wire of proper size for best

performance and longevity of the product.

Do not run power or audio cables on the exterior of the vehicle, including underneath,

as this can result in severe damage to the vehicle and person.

Avoid running power and audio cables next to sensitive electronics within the vehicle,

and be sure to route the signal cables away from the power cables.

Always use rubber grommets when running wire through metal walls or barriers,

and use loom to protect the cable from sharp edges or areas of high heat.

Power ampliers place an increased load on the electrical charging system.

Generally, factory charge systems in good condition should be able to withstand the

extra load of an MPS amplier without a problem. However, multiple amplier systems

can draw excess current and create a serious strain on the electrical system. It is best to

consult your audio specialist for advise on whether or not it is necessary to upgrade your

electrical system to meet the demands of the audio system.

Place an insulated in-line fuse holder of the appropriate current capacity within

16 inches (40cm) of the battery positive (+) terminal. Connect to this to the power

cable

connecting the positive terminal of the amplier. This fuse is designed to protect the

vehicle in the event of a short. Only install the fuse once the power cable has been

secured to the amplier.

Locate a solid metal area as close to the amplier as possible to connect the ground

wire terminal. Use the same gauge wire for ground as for the power wire. The length of

the ground wire should not exceed 36 inches (90cm) from the amplier. To ensure a

solid connection, remove surface paint at the ground point prior to securing the

connector in place.

PROTECTION

Please note that there are no chassis mounted fuses on the MPS ampliers. Instead our

design uses a microprocessor controlled protection circuit which enables the amplier to

optimize the current ow coming into the power supply. This design lowers loss within

the circuitry, increase the power output and improves the sound dynamics of the amplier

for the best listening experience. However, for the safety of you and your vehicle, please

follow instructions for installing an inline fuse with your amplier.

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

1. Power Status Indicator

LED illuminates blue when amplier is properly powered on

2. Protection Status Indicator

LED will illuminate red when the amplier is in faults into protect mode related to over

current, short circuit, thermal protection or internal error within the amplier. If the fault is

caused by thermal protection, the amplier will reset automatically once the heatsink has

cooled to about 70°C (160°F). If the protection LED stays illuminated, turn the amplier o

and check the speakers and wiring.

3. Negative Chassis Ground Connector

Connect to a matching 8 gauge or larger OFC (oxygen-free copper) wire for ground as

used the power wire. The length of the ground wire should not exceed 36 inches (90cm)

from the amplier. To ensure a solid connection, remove surface paint at the ground point

prior to securing the connector in place.

4. Remote Turn-On Connector

Connect to wire lead from a switched +12V source. This could be from a head unit or

switched ignition lead. If neither of these sources is available, switch Turn On Mode to

signal sensing or DC oset.

5. +12VDC Power Connection

For safety and optimum performance, connect an 8 gauge or larger OFC (oxygen-free

copper) wire to the +12V terminal. Connect directly to the positive terminal (+12V) of the

car’s battery via a 50A inline fuse. The fuse must be located within 16 inches (40cm) of the

battery.

6-7. Left & Right Speaker Outputs

Connect speaker wire up to 10 gauge. Group A and Group B connections can be congured

in stereo using the + and – of both L & R outputs, or in a mono conguration using

the L+ and R- within Group A or Group B (DO NOT cross-wire between Group A and B).

3-Channel can also be congured using a stereo in Group A and mono in Group B.

8-9. RCA Inputs

Accepts both low-level and high-level signal via RCA style connectors. Use Input Voltage

Selector to choose appropriate voltage level, and 2/4 channel input selector for number

of inputs used. High-level inputs require the MPS-HL line level adaptor (sold separately) to

convert amplied speaker outputs from factory audio systems to RCA style connections.

MPS 4.400 / Features

10. High/Low Level Input Voltage Selector

Select signal input voltage based on the type of input used. When using an aftermarket

radio, DSP or line level convertor, select Low for levels up to 5V. When using high-level

input from an amplied factory audio system, select High for levels up to 10V.

11. 2/4 Channel Input Mode Selector

Selector allows amplier to accept signal from 2 or 4 channels of input.

Selecting 2CH will take signal from Group A L and R input only and send signal

to Group B L and R channels.

34567 8 9 10 11

12 13 14 15 16 17 18

12. Turn On Mode Selector

Select between 3 modes to turn on the amplier. When using a switched lead such

as the remove output of a radio, select the default position REM. When connecting to

a factory audio system or alternative source, select Signal and the amplier will turn

on when it senses voltage through the inputs. DC (DC oset) may be used in some

vehicles where signal sensing does not reliably turn the amplier on.

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

13 & 16. Input Sensitivity Controller

The input sensitivity controller (gain) is used to properly match input signal levels

from the signal source to optimize the amplier outputs. THIS IS NOT A VOLUME

CONTROL! To properly set, the maximum unclipped output from the radio or source

must be known using either an oscilloscope or, at minimum, a multi-meter and test

program. The amplier can then be properly set to maximize output. If the gain is

not set properly the amplier may clip early and damage your speakers and the

amplier itself. It is highly recommended to use an audio specialist to properly adjust.

Independent gain controls are available for Group A and Group B channels.

14 & 17. Crossover Filter Selector

Select between Full (full range), LP (lowpass) and HP (highpass) depending on the

requirements of the speakers in your system. Selecting LP or HP turns on a 12dB

lter that can be adjusted using the Filter Frequency. This is selected independently for

Group A and Group B channels.

15 & 18. Crossover Frequency Controller

Use this feature to adjust the frequency of the crossover lter between 40 and 400Hz.

This is controlled independently for Group A and Group B channels.

4-CHANNEL LOW LEVEL - RCA INPUTS

4-CHANNEL HIGH LEVEL - SPEAKER TO RCA INPUTS

2-CHANNEL LOW LEVEL - RCA INPUTS

MPS 4.400 / Power And Signal Connections

Optional MPS-HL

Line Level Adaptor

REM

LOW 4CH LOW 2CH

HIGH 4CH

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

1110

2-CHANNEL HIGH LEVEL - SPEAKER TO RCA INPUTS

2-CHANNEL BRIDGED OUTPUTS - LOW LEVEL RCA INPUTS

4-CHANNEL STEREO MODE - HIGHPASS

3-CHANNEL STEREO + MONO MODE - HIGHPASS + LOWPASS

MPS 4.400 / Speaker Connections

REM

LOW 4CH

LOW 2CH

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

1312

2-CHANNEL BRIDGED MODE - STEREO HIGHPASS

2-CHANNEL BRIDGED MODE - LOWPASS SUBWOOFER

1. Power Status Indicator

LED illuminates blue when amplier is properly powered on

2. Protection Status Indicator

LED will illuminate red when the amplier is in faults into protect mode related to over

current, short circuit, thermal protection or internal error within the amplier. If the fault

is caused by thermal protection, the amplier will reset automatically once the heatsink

has cooled to about 70°C (160°F). If the protection LED stays illuminated, turn the

amplier o and check the speakers and wiring.

3. Negative Chassis Ground Connector

Connect to a matching 8 gauge or larger OFC (oxygen-free copper) wire for ground

as used the power wire. The length of the ground wire should not exceed 36 inches

(90cm) from the amplier. To ensure a solid connection, remove surface paint at the

ground point prior to securing the connector in place.

4. Remote Turn-On Connector

Connect to wire lead from a switched +12V source. This could be from a head unit or

switched ignition lead. If neither of these sources is available, switch Turn On Mode to

signal sensing or DC oset.

5. +12VDC Power Connection

For safety and optimum performance, connect an 8 gauge or larger OFC (oxygen-free

copper) wire to the +12V terminal. Connect directly to the positive terminal (+12V) of

the car’s battery via a 50A inline fuse. The fuse must be located within 16 inches (40cm)

of the battery.

6. Subwoofer Outputs

There are two speaker connections are labeled + and -. The two output connections

are internally parallel as this is a single channel amplier. When using both sets of + and

-, you will need to use Ohm’s law to calculate the impedance in a parallel conguration.

Connect speaker wire up to 10 gauge.

7. Remote Level Control

Connector for optional MPS-R1 remote subwoofer level control. This allows

the user to adjust the output level of the amplier on the y from a remote location

within the vehicle.

MPS 1.550 / Features

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

1514

8. High/Low Level Input Voltage Selector

Select signal input voltage based on the type of input used. When using an aftermarket

radio, DSP or line level convertor, select Low for levels up to 5V. When using high-level

input from an amplied factory audio system, select High for levels up to 20V.

9. RCA Inputs

Accepts both low-level and high-level signal via RCA style connectors. Use Input

Voltage Selector to choose appropriate voltage level. High-level inputs require the

MPS-HL line level adaptor (sold separately) to convert amplied speaker outputs from

factory audio systems to RCA style connections.

10 11

3 4 567 8 9

12 13 14

10. Turn On Mode Selector

Select between 3 modes to turn on the amplier. When using a switched lead such

as the remove output of a radio, select the default position REM. When connecting to

a factory audio system or alternative source, select Signal and the amplier will turn

on when it senses voltage through the inputs. DC (DC oset) may be used in some

vehicles where signal sensing does not reliably turn the amplier on.

11. Input Sensitivity Controller

The input sensitivity controller (gain) is used to properly match input signal levels

from the signal source to optimize the amplier outputs. THIS IS NOT A VOLUME

CONTROL! To properly set, the maximum unclipped output from the radio or source

must be known using either an oscilloscope or, at minimum, a multi-meter and test

program. The amplier can then be properly set to maximize output. If the gain is not

set properly the amplier may clip early and damage your speakers and the amplier

itself. It is highly recommended to use an audio specialist to properly adjust.

12. Subsonic Filter Selector

Designed to be used with small subwoofers or vented enclosures with a high tuning

frequency, users can opt to select a 12dB subsonic lter (highpass crossover)

centered at either 25Hz or 35Hz.

13. Lowpass Frequency Controller

This amplier is designed as strictly a subwoofer amplier and therefore the crossover

cannot be defeated. The crossover frequency controller allows the user to adjust the

frequency of the Lowpass crossover lter between 40 and 220Hz.

14. Bass Boost Controller

This allows the user to boost the output of the amplier centered around 45Hz with a

range of 0 to +12dB.

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

1716

HIGH

LOW LEVEL RCA INPUTS

HIGH LEVEL SPEAKER TO RCA INPUTS

SIGNAL

MPS 1.550 / Speaker Connections

SINGLE SUBWOOFER CONNECTION

DUAL SUBWOOFER CONNECTION

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

1918

1. Power Status Indicator

LED illuminates blue when amplier is properly powered on

2. Protection Status Indicator

LED will illuminate red when the amplier is in faults into protect mode related to over

current, short circuit, thermal protection or internal error within the amplier. If the fault

is caused by thermal protection, the amplier will reset automatically once the heatsink

has cooled to about 70°C (160°F). If the protection LED stays illuminated, turn the

amplier o and check the speakers and wiring.

3. Negative Chassis Ground Connector

Connect to a matching 4 gauge OFC or larger OFC (oxygen-free copper) wire for

ground as used the power wire. The length of the ground wire should not exceed 36

inches (90cm) from the amplier. To ensure a solid connection, remove surface paint at

the ground point prior to securing the connector in place.

4. Remote Turn-On Connector

Connect to wire lead from a switched +12V source. This could be from a head unit or

switched ignition lead. If neither of these sources is available, switch Turn On Mode to

signal sensing or DC oset.

5. +12VDC Power Connection

For safety and optimum performance, connect an 4 gauge OFC or larger OFC (oxygen-

free copper) wire to the +12V terminal. Connect directly to the positive terminal (+12V)

of the car’s battery via a 50A inline fuse. The fuse must be located within 16 inches

(40cm) of the battery.

6-8. RCA Inputs

Accepts both low-level and high-level signal via RCA style connectors. Separate

inputs can be used for Group A, Group B and Subwoofer channels. Use Input Voltage

Selector to choose appropriate voltage level, and 2/4 channel and subwoofer mode

input selector for number of inputs used. High-level inputs require the MPS-HL line

level adaptor (sold separately) to convert amplied speaker outputs from factory audio

systems to RCA style connections.

MPS 5.950

/ Features

9. High/Low Level Input Voltage Selector

Select signal input voltage based on the type of input used. When using an aftermarket

radio, DSP or line level convertor, select Low for levels up to 5V. When using high-level

input from an amplied factory audio system, select High for levels up to 10V on Group

A & B inputs, and up to 20V on subwoofer inputs.

10. 2/4 Channel Input Mode Selector

Selector allows amplier to accept signal from 2 or 4 channels of input.

Selecting 2CH will take signal from Group A L and R input only and send signal to

Group B L and R channels.

11. Subwoofer Input Mode Selector

Selector allows amplier to accept signal from Subwoofer inputs or Group A & B

channels of input. Selecting 4CH will take signal from Group A and B only and send

signal to Subwoofer channel.

12. Subwoofer Outputs

There are two speaker connections are labeled + and -. The two output connections

are internally parallel as this is a single channel amplier. When using both sets of + and

-, you will need to use Ohm’s law to calculate the impedance in a parallel conguration.

Connect speaker wire up to 10 gauge.Group A Left & Right Speaker Outputs

13-14. Left & Right Speaker Outputs

Connect speaker wire up to 10 gauge. Group A and Group B connections can

be congured in stereo using the + and – of both L & R outputs, or in a mono

conguration using the L+ and R- within Group A or Group B (DO NOT cross-wire

between Group A and B).

15. Input Sensitivity Controller

The input sensitivity controller (gain) is used to properly match input signal levels

from the signal source to optimize the amplier outputs. THIS IS NOT A VOLUME

CONTROL! To properly set, the maximum unclipped output from the radio or source

must be known using either an oscilloscope or, at minimum, a multi-meter and test

program. The amplier can then be properly set to maximize output. If the gain is not

set properly the amplier may clip early and damage your speakers and the amplier

itself. It is highly recommended to use an audio specialist to properly adjust.

16. Subsonic Filter Selector

Designed to be used with small subwoofers or vented enclosures with a high tuning

frequency, users can opt to select a 12dB subsonic lter (highpass crossover) centered

at either 25Hz or 35Hz.

MOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s ManualMOREL PERFORMANCE SERIES AMPLIFIERS / Owner’s Manual

2120

17. Lowpass Frequency Controller

This amplier is designed as strictly a subwoofer amplier and therefore the crossover

cannot be defeated. The crossover frequency controller allows the user to adjust the

frequency of the Lowpass crossover lter between 40 and 220Hz.

18. Bass Boost Controller

This allows the user to boost the output of the amplier centered around 45Hz

with a range of 0 to +12dB

12 11 1 2 3 567 8 9 10 11 13 144

19 20 21 22 23 24 25

15 16 17 18

19. Turn On Mode Selector

Select between 3 modes to turn on the amplier. When using a switched lead such

as the remove output of a radio, select the default position REM. When connecting to

a factory audio system or alternative source, select Signal and the amplier will turn

on when it senses voltage through the inputs. DC (DC oset) may be used in some

vehicles where signal sensing does not reliably turn the amplier on. Group A Input

Sensitivity Controller

20 & 23. Input Sensitivity Controller