Motive AI Omnicam User manual

AI Omnicam
Installation guide

FAILURE TO PROPERLY AFFIX THE DEVICE TO THE VEHICLE CAN
CAUSE THE DEVICE TO DETACH AND RESULT IN SERIOUS INJURY.
SIMILARLY, BOLTS, NUTS, SCREWS, THE MOUNT, AND OTHER
MECHANICAL COMPONENTS USED TO AFFIX THE DEVICE TO THE
VEHICLE CAN LOOSEN, BREAK, AND FAIL OVER TIME WHICH CAN
ALSO CAUSE THE DEVICE TO DETACH AND RESULT IN SERIOUS
INJURY.
READ AND FOLLOW ALL INSTALLATION AND SAFETY
INSTRUCTIONS PROVIDED IN THE GUIDE AND SUPPORT
ARTICLES. REGULARLY INSPECT THE CAMERA, BOLTS, NUTS,
SCREWS, THE MOUNT, AND MECHANICAL COMPONENTS TO
ENSURE THEY ARE IN GOOD WORKING ORDER AND REMAIN
PROPERLY AFFIXED TO THE VEHICLE.
YOU ARE RESPONSIBLE FOR SECURING THE MOUNT AND
CAMERA TO YOUR VEHICLE, CHECKING THE HARDWARE PRIOR
TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR
ADJUSTMENT, WEAR, AND DAMAGE.
IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND
CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND
ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION
PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY
A PROFESSIONAL INSTALLER.
WARNING

English

Introduction Motive AI Omnicam is the first LTE-built side/rearview camera
introduced to capture 360-degree footage of vehicles. It’s an
AI-enabled hardware product that provides visibility in side-swipe
and rear-collision cases.
1

Installation Requirements: AI Omnicam
Camera with 5-meter
captured cable
What comes in
the box? Front housing
Rear housing Metal plate (1)
Grommet (1) Locknuts (4)
M Screws (10) Allen Key (1)
M bolts (4) Reset pin (1)
Washers (8)
2

Power drill
Tools required Drill bits
Screwdriver with
standard bits and
torques bits
Step drill bit or 17mm
hole saw bit
Wire stripper
Amp fuse for each
camera
Circuit fuse tap or an
in-line fuse tap
3

•Pre-installation
•Permanent Installation
Steps: Installing
AI Omnicam
Pre-installation
4
Click Vehicles from the let-hand side menu.
Click Options in the Action column of your vehicle.
A drop-down menu appears, click Edit Vehicle.
2.
3.
4.
Login to the Fleet Dashboard and click the Admin icon at the
botom let corner.
1.

Select the installation location
a. Let side
b. Right side
c. Rear
Once selected, identify and test the camera mount location.
a. For side camera installation, cowl or door is suggested.
8.
9.
Pre-installation
5
The Edit Vehicle screen displays, scroll down to the Omnicam
section.
Click Assign to enable the AI Omnicam for each mounted
location.
Click Save at the top right corner.
5.
6.
7.

Once selected, identify and test the camera mount location.
a. For side camera installation, cowl or door is suggested.
10.
Pre-installation
For rear camera installation, above roll-up style door, on
top of the roof, or underneath next to the license plate is
suggested.
b.
Note: If you decide to use your own custom bracket to
mount to your mirrors, you choose to do so at your own
risk. Motive is not responsible for any damage or bodily
harm that is occurred from the use of custom brackets.
Please contact Motive’s support team if you have any
questions or concerns.
6

Provide temporary power to the camera using the V or V
red wire and a Amp fuse to assess the mounting location
field of view. Black wire is for ground. Do not use blue
wrapped wires.
11.
Note: If you trim the cable more than 8 inches you would
see following wires:
•Two red wires for POWER. Twist them together to
connect to either V or V source.
•Two unshielded tin wires for GROUND. Twist them
together to connect to ground.
•4 colored wires - blue, green, yellow and orange. Do
not use them and ensure they are never exposed.
What is the use of AI Omnicam’s colored cables?
Note: The surface should be as flat as possible to ensure a
robust connection.
Pre-installation
7

Note: In the future, the above functionality will be available
via Motive Fleet App.
Pre-installation Download Video LAN (VLC player) app on your device12.
Once connected, Open VLC → Network Stream. Type
following URL to view camera video live: rtsp://192.168.2.1/live
14.
Android Google Play Store
Apple App Store
a.
b.
Connect your camera via WiFi to an individual camera to check
its field of view before permanent installation.
SSID : Motive Omnicam <last 6 digits of S/N>
PW: 1234567890
13.
8

You can adjust the Field Of View by moving the camera
around. Ensure you’re geting a clear and desired view.
16.
Once connected, hold the camera with mount assembly on
your selected location with the LED facing upward to check
its Field of View. You do not need to tighten the mount screws
for this testing.
15.
9
Pre-installation

Permanent
installation
Install the mount plate at your selected location using the
provided grommet, M bolts, locknuts, and washers.
5.
Note: Only use the provided hardware kit for installation.
Use the mount plate slots for the provided M bolts, do
not use the other sloted holes for installation.
Follow the steps from the above section.
Disconnect temporary power from the camera.
Use the alcohol wipes provided in the box to wipe the surface
before installing your camera.
Remove the black sticker from the mount plate. Prior to drilling
the holes, note the camera has to be pointed in the opposite
direction of the grommet hole.
1.
2.
3.
4.
10

Route the camera cable through a metal base plate and
grommet hole.
6.
Power the camera permanently using the 12 V or 24 V red
wire. Black wire is ground.
7.
Note: DO NOT USE wrapped blue wires. DO NOT STRIP the
wrapped blue wires as it can cause a short in the device.
Also, if more than 5m length is needed to connect to
vehicle power, it requires an additional wire harness
(suggest to use AWG). This is not provided by Motive.
Note: Ensure that you have access to all M screw
locations on the metal base plate
Permanent
installation
11

Note: The fuse taps/in-line switches are not provided by
Motive. Ensure a Amp fuse is used for each camera.
Connect the front housing of the camera mount using M
screws. Allen key is provided to tighten these M screws.
Connect the rear housing of the camera mount with M
screws.
Ensure the LED of the camera is facing up towards the sky
before tightening the screws.
Now, check the Field of View (FOV) of your installed camera.
You can untighten the screws shown below to rotate the
camera within the mount to adjust the FOV.
8.
9.
10.
11.
Once securely connected, your camera may undergo a
sotware update that is indicated with a white flashing LED.
The LED turns solid white once the camera is updated and is
ready to record.
12.
13.
Note: Remove plastic protective film on the camera once
installation is complete.
12
Permanent
installation

Note
The Motive AI Omnicam is a driver and fleet management aid only. It is not a substitute for
safe, conscientious driving and cannot compensate for distracted, inatentive, or impaired
driving. All warning and alert features provided by Motive products are for informational
purposes only. No warning or alert feature provided by Motive products are intended to
replace your responsibility
to observe all road and driving conditions, abide by all trafic regulations, and use safe
driving judgment at all times.
Video recordings made by the Motive AI Omnicam are for personal or internal use only.
The Motive AI Omnicam uses artificial intelligence to identify animate and inanimate
objects in video and images, potentially including individual persons, and the data
captured by the AI Omnicam may be used in the creation and production of other Motive
products
and services.
In some jurisdictions it could be considered an invasion of privacy rights to take or
Product was validated using suite of reliability tests that were guided by the
standards below:
ISO--
ISO--
ISO -
IEC 
IEC --
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment of and on, the
13
Safety & Privacy

user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the equipment.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment and RSS  RF exposure compliance requirements. This
equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body. This Transmiter must not be co-located or operating
in conjunction with any other antenna or transmiter.
Changes or modifications not expressly approved by Motive could void the user's
authority to operate this equipment.
This device contains license-exempt transmiters / receivers that comply with Part 15 of
the FCC Rules and with Innovation, Science and Economic Development Canada's
license-exempt RSS(s). Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
TM
Covered by patents at patentlist.accessadvance.com
Safety & Privacy
14

Troubleshooting
Resources
855-434-3564
[email protected]
help.gomotive.com
Scan this code or visit
gomotive.com/omnicam-install for detailed
information and recommendations on installing
and assigning your AI Omnicam.