Mottura 99.736 User manual

EXTERNAL KEYBOARD
99.736 / 99.749
GENERAL WARNINGS
Mottura Serrature di Sicurezza S.p.A. thanks you for choosing this product and reminds you:
- to read these instructions very carefully before installing and using this product and before doing any maintenance.
- to keep these instructions for future use and attach the sales receipt to validate the warranty.
- in case of problems, contact your authorized dealer only.
“DO NOT use a liquid, spray, or wet cloth to clean the escutcheon! If liquids enter the scanner, they will oxidize and permanently damage
its components. Use a dry cloth only. DO NOT paint the escutcheon with any method or substance. Failure to follow these instructions will
immediately void the warranty.”
Mottura Serrature di Sicurezza S.p.A. may change the characteristics of the products described in these instructions at any time and without
notice. Always disconnect power supply before carrying out any connection/assembly operation and/or subsequent procedure.
WARRANTY TERMS
This device has been inspected by Mottura Serrature di Sicurezza S.p.A. and is guaranteed against all manufacturing defects for the period
dened by Italian law; the period begins on the date of purchase as demonstrated by the sales receipt. The warranty is eective if the sales
receipt, bearing information identifying the device, is shown to the dealer or service personnel. The warranty covers the replacement or
repair of parts found defective due to faulty manufacture; shipping costs to and from service centers are charged to the customer.
In case of a repeated malfunction of the same origin or a malfunction that cannot be repaired, Mottura Serrature di Sicurezza S.p.A. may
decide, in its nal judgment, to replace the entire device. The warranty on the replacement device will continue to the expiration of the
original device. If the device must be serviced at the customer’s home, the customer is required to pay (if requested) a minimum charge to
cover the transfer costs of authorized service personnel.
Transport is at the customer’s risk if the customer ships the device, and at the service personnel’s risk if the device is picked up and transpor-
ted by service personnel.
LIMITS OF LIABILITY
The warranty does not cover damage deriving from:
- negligence, carelessness, or use other than as described below
- failure to protect the device before doing any procedure that may generate scrap or waste (welding, drilling of panels, drilling of structure,
etc.) that prevents its correct functioning
- maintenance work not conforming to these instructions or done by unauthorized personnel
- use of accessories/components that are not original Mottura products
- shipping of the device without the necessary precautions
- any circumstances not attributable to manufacturing defects.
Operating temperature: -10°C to +55 °C.
In addition, Mottura Serrature di Sicurezza S.p.A. declines all liability for any harm to persons or damage to property deriving from failure to
comply with all of the instructions and warnings contained in this manual.
5 protection against dust
and wire contact with
dangerous parts.
4 protection against
splashing water.

2
99337GB - REV. 03
CAUTION : the system is supplied in factory condition, i.e., any MOTTURA TAG can operate the lock and access
programming. The rst thing the user must do is delete all of the ngerprints and TAGs to prevent any unauthorized
access. After this is done, the user MUST MEMORIZE the ngerprints and TAGs that will have access to the opening.
1. ESCUTCHEONS
CAPACITIVE KEYPAD
KEYPAD
ACTIVITY LED
ACTIVITY LED
TRANSPONDER TAG READER
TRANSPONDER TAG READER
CONNECTOR
CONNECTOR
ESCUTCHEON COVER
ESCUTCHEON COVER
The external KEYBOARD with TRANSPONDER escutcheon has 3 function keys, a transponder reader (RFID), a
buzzer, and three LEDs (red-yellow-green).
It lets you open/close the lock in two ways:
- CODES: the keyboard lets you enter a maximum of 100 codes authorized to operate the lock.
- TRANSPONDER KEY (TAG): the escutcheon checks the presence of a transponder key (TAG – not included)
placed near the center of the keypad.
The number of stored TAG keys is NOT tied to the
escutcheon but to the device to which it is connected :
XMODE protected tag system : 255 TAG
XMODE free tag system : 200 TAG
XNOVA / ELECTRONIC / ELECTRICAL LOCKS : 200 TAG
TAG - CARD
Art. 99691/99705
TAG - KEY
Art. 99692/99706

3
The function keys are:
- numeric buttons 1, 2, E to be used during programming.
The LED show door state on any operation under way :
- RED LED ashing lock closed
- RED LED on lock closing
- GREEN LED ashing lock open
- GREEN LED on lock opening
- YELLOW LED on + 3 beeps signal to replace batteries
- YELLOW LED on + double high-low sound batteries low
The signal to replace the batteries is given before any operation is carried out (opening/closing, etc.).
You should replace the batteries as soon as possible to ensure correct functioning of the lock.
Buzzers signal when the lock has been opened or closed.
2. ASSEMBLY AND ELECTRICAL CONNECTION
Make a 62 x 36 mm gap in the door panel as shown in the gure, then connect the wire to the lock.
The connections must be made by a qualied technician competent to existing electrical safety standards and to
Rules of Good Engineering.
N.B. All connections must be made with the electrical supply switched o and the batteries disconnected.
... WITH XMODE ELECTRONIC LOCKS
Internal
escutcheon
Cable 99.699
Cable
99.698
Protect wires
against any
external
tampering

www.mottura.it
230 Vca
230 Vca
... WITH OTHER ELECTRONIC / ELECTRICAL / XNOVA LOCKS
To connect the escutcheon to XNova or other electronic/electrical locks, use an interface card (RELAY MODULE Art. 99724 with
MAIN POWERED - Art. 99746 with MAIN POWERED and BATTERY) to be purchased separately. See the article’s instruction manual.
AC/DC Adapter
12Vdc - Art. 99.683
AC/DC Adapter
12Vdc - Art. 99.683
Wired battery pack
(9V) - Art. 99.703/704
Dry contact
99.727
(White and
purple)
Cable
99.699
6. MANAGING TAGS / CODES WITH OTHER ELECTRONIC/ELECTRICAL/XNOVA LOCKS
5. MANAGING TAGS /CODES WITH XMODE
ATTENTION : See the lock user manual (chapter 5) for management of TAGS.
ATTENTION : See the manual of relay module (chapter 5) for management of TAGS.
ATTENTION : See the lock user manual (chapter 8) for management of CODES.
ATTENTION : See the manual of relay module (chapter 6) for management of CODES.
ATTENTION: if no TAGS are memorized on the control unit (new lock or after a reset), any free Mottura TAG can
be used to enter programming mode! You SHOULD IMMEDIATELY MEMORIZE rst your master TAGS, then
any service TAGS, to guarantee maximum security.
After this operation, the control unit will accept only the memorized TAGS.
99337GB - 06/20 - a_023184
Аrt. 99.724
Аrt. 99.746
OR
Pursuant to article 26 of Italian Legislative Decree no. 49 of 14 March 2014 “Implementation of EU Directive 2012/19 concerning
waste electrical and electronic equipment (WEEE)” and article 9 of Italian Legislative Decree no. 188 of 20 November 2008 “Imple-
mentation of EC Directive 2006/66 on batteries and accumulators and waste batteries and accumulators” adequate waste sorting for
subsequent sending of disposed equipment to recycling, treatment and environmentally compatible disposal contributes to avoiding
possible negative eects on the environment and human health and promotes reuse and/or recycling of the materials composing
the equipment. Unlawful disposal of the product by the user may result in the application of penalties pursuant to current laws and
regulations on the matter. We remind that batteries and power adapters, if present, must be removed before the device is disposed.
Batteries and adapters must be collected and separately disposed.