Motus M-FUSION User manual

1
OWNER’S MANUAL
MODEL: M-FUSION
DESCRIPTION: Motus® Fusion Group Indoor Racing Bike
INCLUDES: Motus® M-Racing PC; Dual SPD & Cage Pedals & CHR
ALLRIGHTS RESERVED; COPYRIGHT® MOTUS USA 2008

2
Dear Motus USACustomer,
We would like to thank you for buying our studio sports training equipment ,hope
that it affords you the desired satisfaction. Please note and follow the information
and instructions for assembly and use. If you have any questions, please contact at
any time.
SAFETYINSTRUCTIONS
Before you start training on your sports training equipment, please read the
instructions carefully.
Be sure to keep the instructions and any other accompanying in case of repair and
for spare parts delivery.
zUse only original parts as delivered.
zCheck before the equipment is first used, and again at regular intervals, that all
screws, bolts, nuts and other connections have been done up tightly, to ensure
that your training equipment is in a safe operating condition at all items.
zPlace the bike on an even, non-slippery surface. Because of possible corrosion,
the usage of the bike in moist areas is not recommended.
zCheck every 1-2 month that all connecting elements are tight fitting and are in
the correct condition.
zOnly carry out training work on the equipment when it is in perfect working
order.
zOne person for training may only use the equipment.
zThe bike is designed for adult. Children are not allowed to use this bike.
zAlways pay attention that you or any other persons never bring parts of the
body in close proximity to any parts of the equipment that are still moving.
zConsult your physician before starting with any exercise program. He can
advise which kind of training and impact is suitable.
zWhen making settings for any adjustable parts, check that they are in the right
position and also check the marked maximum setting.
zPlease follow the advice for correct training as detail in training instructions.
zThis bike not suits for therapeutic use.
zThe user’s max. Weight in 120 KGS.

3
Basic Maintenance and Pre-us Suggestions and Requirements:
- Lubricant is recommended as a Silicone Spray (Do Not Use WD-40). Lubricate
seat neck and display neck if adjustment becomes difficult.
- Flywheel should be thoroughly cleaned prior to; and port workout. This will
prevent build up on flywheel as-well as limit rough operation of the unit.
- Check foot mounts to ensure they are adjusted accordingly.
- Check Resistance to ensure that all bikes have matching tension.
- Adjust Resistance to desired preference.
- Always keep bikes clean and wipe down after use, for improved product
longevity.
PARTS LIST:
Item Description Quantity Item Description Quantity
1 Main Frame 1 39 Nut 2
2 Rear Foot Bar 1 40 Adjustable Bolt 2
3 Front Foot Bar 1 41 Lock Nut 2
4 U-Zone Bar 1 42 Function Set 2
5 Seat Post 1 43 Stopper Set 1
6 Handle Post 1 44 Function Controller 1
7 Seat Slider 1 45 Screw 2
8 Handle Bar 1 46 Inner Chain Cover 1
9 End Cap 2 47 Screw 2
10 Adjustable Pad 2 48 Belt 1
11 Move Wheel 2 49 Belt Deck 1
12 Hex Head Bolt 2 50 Screw 4

4
13 Nylon Nut 2 51 Outer Chain Cover 1
14 Washer 4 52 Round Head Screw 6
15 Hex Head Bolt 4 53 Left Crank 1
16 Cap Nut 2 54 Right Crank 1
17 End Cap 2 55 Left Pedal 1
18 Bearing 2 56 Right Pedal 1
19 Bearing 2 57 Bolt 2
20 S Nut 1 58 Cap 2
21 Belt Wheel Rod 1 59 Plug 2
22 Left Cover 1 60 Knob 4
23 Right Cover 1 61 Flat Washer 2
24 Top Left Cover 1 62 Seat 1
25 Top Right Cover 1 63 Round Head Bolt 2
26 Rear Cover 1 64 End Cap 1
27 Front Left Cover 1 65 Washer 2
28 Front Right Cover 1 66 Spanner 1
29 Screw 1 67 Spanner 1
30 Screw 1 68 Washer 2
31 Screw 2 69 Nut 2
32 Screw 2 70 Foam Pad 2
33 Tapping Screw 2 71 Bracket 1
34 Tapping Screw 2 72 Bolt 1
35 Flywheel 1 73 Nut 1
36 Belt Wheel 1 74 Washer 1
37 Fly Wheel Rod 1 75 Spring 1
38 Spring Washer 2

5
OVERVIEW CHART:

6
PACKING PARTS LIST:

7
zRemove all parts and bags from box.
zRead the owner’s entire manual before assembly.
zLet out all parts and hardware pack as shown in pre-assembly checklist drawing.
zSome parts may be pre-assembled.
Step 1.
Slide the Rear Foot Bar (2) to the rear of the Main Frame
(1) with two Washers (14) and two Hex Head Bolts (15)
as shown in Figure 1.
Tighten all bolts used in Step #1 with one Spanner (66)
at this time.
Step 2.
Slide the Front Foot Bar (4) to the front of the Main
Frame (1) with two Washers (14), two Spring Washers
(68) and Hex Head Bolts (15) and Cap Nuts (16) as
shown in Figure 1.
Tighten all bolts used in Step #2 with two Spanners (66)
& (67) at this time.
Step 3.
Insert the U-Move Bar (4) into the holes of the Front
Foot Bar (3) with two Washers (65) and Round Head
Bolts (63) as shown in Figure 1.
Tighten all bolts used in Step #3 with one Spanner (66)
at this time.
Step 4.
Fix the Left Pedal (55) and Right Pedal (56) to the L&R
Crank (53 & 54) as shown in Figure 2.
Tighten the Pedals used in Step #4 with one Spanner
at this time.

8
Step 5.
Insert the Seat Post (5) into the tube of the Main Frame (1)
with Knob (60).
Hands Tighten only at this time.
Step 6.
Attach the Seat (62) on the bar of the Seat Slider (7) first. Then
slide this set onto the Seat Post (5) with Flat Washer (61) and
Knob (60) to tighten as shown in Figure 3.
Hands Tighten only at this time.
Step 7.
Insert the Hand Post (6) into the tube of the Main Frame (1)
with Knob (60).
Hands Tighten only at this time.
Step 8.
Insert the bolt of the Pads(70) into the holes of the Hand Bar(8)
With two Nuts(69) as shown in Figure 4.
Tighten all bolts used in Step #8 with one Spanner (67) at this
time.
Step 9.
Attach the Handle Bar (8) on the Hand Post (6) with one Flat
Washer (61) and Knob (60) to assemble as shown in Figure 3.
Hands Tighten only at this time.
MAKE SURE ALL NUTS AND BOLTS ARE TIGHTENED.
FUNCTIONS ADJUSTMENT
Adjustment the Tension at the Adjust Screw as Detail A.
Adjustment Function at the Lock Nut and Adjust Wire see
Detail B.
Adjust must tighten the Lock Nut.