Mount-It! MI-2751 User manual

English
Installation Instruction
1
UNPACKING INSTRUCTIONS
!Carefully open the carton, remove contents and lay out on cardboard or other
protective surface to avoid damage.
!Check package contents against the Supplied Parts List in the next page to assure
that all components were received undamaged. Do not use damaged or defective
parts.
!Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
!Install and operate this device with care. Please read this instruction before
installation, and carefully follow all instructions contained herein. Use proper safety
equipment during installation.
!Please call a qualified installation contractor for help if you don't understand these
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaims any and all liability for injury or damage
arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Supplied Par ts List
2
CAUTION!
WARNING
!This monitor desktop mount must be securely
attached to the horizontal desk. If the mount is
not properly installed it may fall, resulting in
possible injury and/or damage.
(1) Pole-a (1) Swivel Arm-d(1) “C” Clamp-b
(1)Support Plate-j(1)M10 Bolt-i (1)M10 Washer-k (1)Spring Washer-l
(4)M4 Spacer-s
(4)M4x12
Thumb Bolt-q (4)M4x30 Bolt-r
(1) “C” Clamp Brace-c
(1) VESA Plate-e (3) M5x14 Bolt-f (2) M8x12 Bolt-g (1) Nut-h
(1) Grommet Base
Plate-m (1)Wire Clip-n1 (1)Allen Key-o
(1)Wrench-p
(2)Wire Clip-n2

Step 1 Install the Pole to the Desktop
3
Option A: Desk Clamp Install a
1. Install the “C”-Clamp Brace(c) to the Pole
(a) using 3pcs M5x14 Bolts(f), and tighten
using the Allen Key(o), see Figure 1.
2. Install the “C”-Clamp(b) to the pole
assembly according to the thickness of the
desktop. The thickness can be changed to
three positions. Connect it using 2pcs M8x12
Bolts(g), and tighten using the Allen Key(o).
Tighten the “C”-Clamp to the desktop using
the plastic knob, see Figure 2.
Figure 1
c
f
Figure 2
g
o
b
Plastic Knob
Option B: Grommet Base Install
If the existing grommet hole comes with a
plastic protector, remove it to ensure a flat
surface before installing the desk mount.
1. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(f), and
tighten using the Allen Key(o), see Figure 3.
2. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Figure 4.
a
Figure 3
m
f
Figure 4
j
i
k
l
Existing Grommet Hole Installation

Step 1 Install the Pole to the Desktop
4
Self Drilled Grommet Hole Installation
Option B: Grommet Base Install
1. Position the Pole(a) on the mounting
surface and mark the center hole. Drill a 3/8"
(10mm) diameter hole at the marked position
through the mounting surface.
2. Install the Grommet Base Plate(m) to the
Pole(a) using 3pcs M5x14 Bolts(f), and
tighten using the Allen Key(o), see Figure 5.
3. Position the Pole(a) on the mounting
surface and secure using the Support Plate
(j), M10 Washer(k), Spring Washer(l) and
M10 Bolt(i). Fasten the M10 Bolt using
provided Wrench(p), see Figure 6.
a
Figure 5
m
f
Figure 6
j
i
k
l
Step 2 Install Arm to the Pole
d
o
Install Swivel Arm(d) to the
Pole(a). Fasten the bolt with
supplied Allen Key(o). Attach
the Wire Clip(n1,n2) to the
Pole(a) and Swivel Arm(d).
n1
n2

5
Step 3 Attach the VESA Plate to the Monitor
For Monitor with Curved or
Recessed Back
s
r
Step 4 Slide the Monitor onto the Head of Swivel Arm
Install the security Nut(h). Make
sure the security nut is installed
before you rotate the monitor.
Slide the monitor onto the head of
Swivel Arm(d) as shown in the
above diagram.
h
For Monitor with Flat Back
q

Step 6 Manage the Wires and Store the Allen Keys on Wire Clip
Step 5 Make the Necessary Adjustments
6
o
Use the supplied Allen Key(o) to make
the necessary adjustments.
o
Tighten the bolt with the supplied Allen
Key(o) to fix the tilt angle.
Fix the tilt angle
Thank you for choosing our products!