SCT RC-CUBBY Series User manual

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 1
Thank you for your purchase! Sound Control Technologies’
RC-CUBBY™ Series camera mounts offer a simple, one-person
installation technique, facilitating easy deployment and results
in an extremely clean look. You won’t even know we’re there!
One
Person
Install
Pro Tip: If you’re having trouble fitting the wall clamp assembly into
the knockout space, you can adjust the arm length by turning the nut.
Flange
3/4 View
Front View
No. 1 • RC-CUBBY Back Box
INCLUDED PART LIST
No. 1 RC-CUBBY Back Box (Qty 1)
No. 2 Wall Clamp Assembly (Qty 4)
+
KIT-SPECIFIC
Bezel, Camera Plate and Hardware
BEFORE YOU GET STARTED:
Please make sure that you have all parts indicated before you begin
mount assembly, and that any in-wall boxes are mounted in accordance with commercial construction
best practices.
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 2
Bottom View
Top View
Right Side
View
Left Side
View
RC-CUBBY Back Box
Front View
Pro Tip:
If any studs are
close enough, you can use
these holes to further
secure your Back Box!
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 3
Page 4
Page 7
RC7-PD2™ supporting the Poly Director II System
RC8-CQC™ supporting the Cisco Quad Camera
Step 6: If you’re also integrating one of our camera extension kits, feed the SCTLink™ cable through the cable
knockout.
ASSEMBLY INSTRUCTIONS
Part Two: Prepare the Camera Plate (and RemoteCam™ Camera End Module if also integrating extension kit).
What are you installing?
5d: Side View
5c: Side View
5c: Once the front of the clamp assembly is in place, you will be able
to press in the rear hooks (circled in 5c: Side View).
5b: Side View
5b: As you angle the clamp, make sure to line up the front hooks
(circled in 5b: Side View) with their appropriate slots in the knock out.
5a: Side View
5a: Front View
Please Note: The side views below
will not be visible once the backbox
is inserted into the wall, but shown
to help visualize how the clamp
assemblies are installed in the
knockout openings.
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 4
ASSEMBLY INSTRUCTIONS
Step 1: If also integrating an RC7-PD2™ Camera Extension Kit, use the black
4-40x1/4” Flat Head Screws
(No.
10, Qty 4) to attach the Camera Module Mounting Ears
(No. 9, Qty 2) to your RC7-CE™ Camera Module (No. 8, Qty 1)
.
Use the first set of holes, closest to the flange, and make sure the flange is pointed toward the connectors (i.e.
HDMI, Ethernet, SCTLink™) on the rear panel of the module. See “Step 1 View” image on Page 5 for reference.
No. 10
No. 9
No. 8
W HAT’S NOT IN THE BOX (included in the RC7-PD2-K™ Camera Extension Kit)
No. 7
No. 6
No. 5
No. 4
No. 3
No. 2
No. 1
W HAT’S IN THE BOX (RC-CUBBY-PD2™)
INCLUDED KIT-SPECIFIC PART LIST
No. 1 RC-Cubby Back Box (Qty 1)
No. 2 Wall Clamp Assembly (Qty 4)
No. 3 Bezel BBZ1-0 (Qty 1)
No. 4 Camera Plate (Qty 1)
No. 5 6-32x3/8” Torx Pan Head Screw, Zinc (Qty 4)
No. 6
No. 6 Adaptor Plate ADP1-0 (Qty 1)
No. 7 M3x10 Thumb Screw, Black (Qty 4)
RC-CUBBY-PD2™ supporting the Poly Director II System
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 5
4
3
1
Steps 4+5 View
Step 3 View
8
7
1
Pro Tip: W hen installing the Camera Plate, make sure you’re
holding it perpendicular to the wall; do not try to “hook” it into
the unit.
Step 5: Insert the hooks of the Camera Plate
(No. 4, Qty 1)
through the
Bezel opening, and into the slots on the bottom of the Back Box, pushing
in to secure. This will hold the adapter plate in place.
Step 2: Next, you’ll attach the Step 1 Assembly to the Adaptor Plate
(No. 6, Qty 1)
using the zinc
6-32x3/8” Torx
Pan Head Screws
(No. 5, Qty 4)
. Make sure the cross bar of the Adapter Plate is on the bottom side of the
Camera End Module, as seen above in “Step 2 View”.
Step 3: Carefully drop your Step 1+2 Assembly inside the Rectangular Knockout (see Page 2 for reference) in
the RC-CUBBY Back Box (No. 1, Qty 1); the assembly will be behind the wall, with the connections facing
upwards for ease of access. See “Step 3 View” image below for assembled reference.
Step
Step 4: Hang the
Bezel
(No. 3, Qty 1)
off the front of the Back Box, with the large opening at the bottom. The
small centered tab on the Back Box will line up with the small center slot of the Bezel (center tab/slot circled
below in “Steps 4+5 View” image for reference).
5
6
Step 2 View
8
7
Step 1 View
9
ASSEMBLY INSTRUCTIONS...cont.
RC-CUBBY-PD2™ supporting the Poly Director II System
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 6
Great job, you’re finished!
Thank you for your support!
Assembled Front View
Assembled Bottom View
Assembled Top View
Assembled Side View
Step 7 View
7
4
11
If you’re also integrating our RC7-PD2™ Camera
Extension Kit, connect the rest of the cables to the
Camera End Module, per our Application Guide,
making sure you connect the SCTLink™ cable last.
Step
Step 7: Place the Poly Director II
(No. 11, Qty 1) on
to the
Camera Plate and attach using the M3x10 Thumb
Screws (No. 7, Qty 4), making sure the camera is
secure. See “Step 7 View” to the right for reference.
If applicable, attach the other end of the cables to the
Director II and gently tuck them into the Back Box.
That’s it, you’re done!
Step 6: On the inside of the Back Box, there are tabs on the right-and-left lower side. Use a flat head screw
driver to slightly move out each tab past the notch on the Camera Plate, securing it in place.
ASSEMBLY INSTRUCTIONS...cont.
RC-CUBBY-PD2™ supporting the Poly Director II System
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 7
ASSEMBLY INSTRUCTIONS
Step 1: If also integrating an RC8-CQC™ Camera Extension Kit, use the black
4-40x1/4” Flat Head Screws
(No.
9, Qty 4) to attach the Camera Module Mounting Ears
(No. 8, Qty 2) to your RC8-CE™ Camera Module (No. 7, Qty 1)
.
Use the first set of holes, closest to the flange, and make sure the flange is pointed toward the connectors (i.e.
HDMI, Ethernet, SCTLink™) on the rear panel of the module. See “Step 1 View” image on Page 8 for reference.
No. 9
No. 8
No. 7
W HAT’S NOT IN THE BOX (included in the RC8-CQC-K™ Camera Extension Kit)
No. 6No. 5No. 4
No. 3
No. 2
No. 1
W HAT’S IN THE BOX (RC-CUBBY-CQC™)
INCLUDED KIT-SPECIFIC PART LIST
No. 1 RC-Cubby Back Box (Qty 1)
No. 2 Wall Clamp Assembly (Qty 4)
No. 3 Bezel BBZ2-0 (Qty 1)
No. 4 Camera Plate (Qty 1)
No. 5 6-32x3/8” Torx Pan Head Screw, Zinc (Qty 4)
No. 6
No. 6 Adaptor Plate ADP2-0 (Qty 1)
RC-CUBBY-CQC™ supporting the Cisco Quad Camera
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 8
4
3
1
Steps 4+5 View
Step 3 View
8
7
1
Pro Tip: W hen installing the Camera Plate, make sure you’re
holding it perpendicular to the wall; do not try to “hook” it
into the unit.
Step 5: Insert the hooks of the Camera Plate
(No. 4, Qty 1)
through the
Bezel opening, and into the slots on the bottom of the Back Box,
pushing in to secure. This will hold the adapter plate in place.
Step 2: Next, you’ll attach the Step 1 Assembly to the Adaptor Plate
(No. 6, Qty 1)
using the zinc
6-32x3/8” Torx
Pan Head Screws
(No. 5, Qty 4)
. Make sure the cross bar of the Adapter Plate is on the bottom side of the
Camera End Module, as seen above in “Step 2 View”.
Step 3: Carefully drop your Step 1+2 Assembly inside the Rectangular Knockout (see Page 2 for reference) in
the RC-CUBBY Back Box (No. 1, Qty 1); the assembly will be behind the wall, with the connections facing
upwards for ease of access. See “Step 3 View” image below for assembled reference.
Step
Step 4: Hang the
Bezel
(No. 3, Qty 1)
off the front of the Back Box, with the large opening at the bottom. The
small centered tab on the Back Box will line up with the small center slot of the Bezel (center tab/slot circled
below in “Steps 4+5 View” image for reference).
5
6
Step 2 View
8
7
Step 1 View
9
ASSEMBLY INSTRUCTIONS...cont.
RC-CUBBY-CQC™ supporting the Cisco Quad Camera
RC-CUBBY™ Series Camera Mount Installation Instructions

VISIT US @ W W W .SOUNDCONTROL.NET • QUESTIONS? CALL TECH SUPPORT: 203-854-5701 • PAGE 9
Great job, you’re finished!
Thank you for your support!
Assembled Bottom ViewAssembled Top View
Assembled Side + Front View
Step 6: On the inside of the Back Box, there are tabs on the right-and-left lower side. Use a flat head screw
driver to slightly move out each tab past the notch on the Camera Plate, securing it in place.
If you’re also integrating our RC8-CQC™ Camera Extension Kit, connect the rest of the cables to the Camera
End Module, per our Application Guide, making sure you connect the SCTLink™ cable last.
Step 7: Attach the Cisco Quad Camera
(No. 10, Qty 1)
to the Camera Plate by snapping both sides into place,
making sure the camera is secure. Lock the camera in place using the red lever on the Quad Camera. To be fully
level, move the blue tabs on the Quad Camera metal rail to 0
°
.
If applicabl
If applicable, attach the other end of the cables to the Quad Camera and gently tuck them into the Back Box.
Step 8: Tilt the Cisco Quad Camera up into position, and you’re done!
ASSEMBLY INSTRUCTIONS...cont.
RC-CUBBY-CQC™ supporting the Cisco Quad Camera
RC-CUBBY™ Series Camera Mount Installation Instructions