Mountup MU2001 User manual

Polished Aluminium Single Monitor Wall Mount
Instruction Manual
If you have any questions , please contact us.
75x75
100x100
1.5~8kg
3.3~17.6lbs
32"
MU2001
V2.0

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, please contact us.
Beforestarting assembly, verify all parts are included and undamaged. Improperinstallation may cause damage or
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
WARNING!
PACKAGE CONTENTS
01
B (x1)
VESA Plate
A (x1)
Arm Assembly
NOTE: Not all hardware included will be used.
M-E (x4)
D6 Washer
M-C (x4)
M6x12
M-B (x4)
M4x16
M-D (x4)
M6x16
M-A (x4)
M4x12 M-F (x4)
Spacer
W-B (x3)
Anchor
W-C (x3)
Washer
W-A (x3)
Lag Bolt
( )
Installation Tools
Awl
D (x3)
Decorative Cover
E(x1)
6mm Allen Key
C (x1)
Bolt

ASSEMBLY STEPS
02
STEP 1: Attach Arm Assembly to Wall
OPTION A: Wood Stud Installation
ø 4.5mm
(ø 3/16")
55mm
(2.2")
X
W-C W-A
Caution:
Do not use anchor in drywall
or wood！
A
A
Locate your studs. Verify and mark
Position the Arm Assembly (A) at your
desired height and line up the holes
withyour stud center line. Level the
Arm Assembly (A) and mark the pilot
hole locations.
Drill pilot holes using a ø3/16 in.
(ø4.5 mm) diameter drill bit.
Install Arm Assembly (A) using lag
bolts (W-A) and washers (W-C).
Tighten the lag bolts until they are
Assembly (A).

03
STEP 1: (Continued)
60mm
(2.4")
ø10mm
(ø 3/8")
W-C W-A
W-B
A
A
OPTION B: Solid Concrete Wall Installation
60mm (2.4 )
Position the Arm Assembly (A) at
yourdesired height , level the Arm
Assembly (A) and mark the pilot hole
locations.
Drill pilot holes using a ø3/8 in.
(ø10 mm) diameter drill bit.
Install Arm Assembly (A) using lag
bolts (W-A), anchors (W-B)and
washers (W-C). Tighten the lag bolts
the Arm Assembly (A).

04
STEP 2: Attach Decorative Cover
Attach Decorative Covers (D) to Lag Bolts (W-A).
D
W-A

NOTE: Hand tighten screws to avoid over tightening.
STEP 3 : Attach Monitor
05
M-A
M-C
M-E
E
M-B
M-D
M-E
M-F
E
OPTION B: Curved Back Monitor
Attach the VESA plate (B) to back of monitor and secure
with screws (M-B) or (M-D) with washers (M-E)and
OPTION A: Flat Back Monitor
Attach the VESA plate (B) to back of monitor and
secure with screws(M-A)or(M-C) with washers(M-E)
B
B
washers(M-F)using 6 mm Allen Key (E). Do not tighten the
screws excessively or your monitor might be damaged.
using 6 mm Allen Key (E). Do not tighten the screws
excessively or your monitor might be damaged.

06
Slide the monitor onto the head of swivel arm, install the security bolt (C). Make sure the security
bolt is installed before you rotate the monitor.
STEP 4: Hang Monitor
Refer to below illustrations to adjust tilting angle of your monitor.
Tilts down
Note:
1. Loosen the tilting bolt.
2. Adjust monitor to your
desired tilting angle.
3. Retighten the tilting bolt to
Important Notice:
The gas spring tension is pre-set to the weakest level by default, please hold your monitor
by both hands and do not let go so soon after the VESA plate is attached to the swivel arm.
It's suggested to loose hold of the monitor in a slow & gentle way while observing if the gas
spring arm falls down greatly.
C
E

07
STEP 5: Adjust Tension
Note1:
Be sure to keep the arm in horizontal position during adjustment.
Falls down
After being attached to the arm, the monitor falls down
and can not stay at the desired height by itself.
Turn counter-clockwise(“+”direction) to increase gas
spring tension until the monitor can stay at the desired
height by itself.
After being attached to the arm, the monitor rises up and
can not stay at the desired height by itself.
Turn clockwise(“-”direction) to reduce gas spring tension
until the monitor can stay at the desired height by itself.
Rises up
CAUTION
As for how many circles the screw should be turned, the table below is for reference.
Note2:
tension in upper arm using 6 mm allen key (E).
E
Monitor Weight 1.5kg 3kg 4kg 5kg 6kg 7kg 8kg
Circles (AT LEAST) 108643min 12

08
STEP 5: (Continued)
STEP 6: Cable Management
On the bottom portion of the spring arm, insert the cable and slide the cable cover down;
On the upperportion of the spring arm, insert the cable and press the tabs on the inside of the cable cover
slightly inward and slide down to reattach the cable cover.
For both bottom and upper portion of the spring arm, just slide the cable cover up and away from the spring
1
2

Adjust as Desired
09
Note: When tilted, if the monitor sags or does not stay,
please fasten the tilting bolt on the mount until the
monitor canbe held at any angle as needed.
+90°
-45°
max280mm
180°
360°
360°
180°
Adjust monitor position and rotation.

Product Dimensions
10
2.6"
0.9"
7.3"
2.4"
2.9"
"9.2
"9.3
"5.4
"
11
3.9"
4.5"
"7.6
8.7"-10.8"
-45°
+90°
180°
360°
180°
360°

CAUTION AND MAINTENANCE:
• Never allow children to climb, stand, hang, or play on any part ofmonitoror stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please contact us.