MP-Man ICR 110 User manual

DIGITAL VOICE RECORDER
MODEL:ICR-110
BEFORE OPERATING THIS PRODUCT,
PLEASE READ THESE INSTRUCTIONS
COMPLETELY.
ICE
“Read all instruction before use” and save for future reference
PRECAUTIONS
To maintain optimum performance:
Do not use unit in places which are extremely hot, cold, dusty or humid.
Do not use or keep the unit in following places.
In a high humidity area such as a bathroom or near a hearer.
In an area exposed to direct sunlight (e.g, inside car where it become extremely
hot).
Near sources of strong magnetism, such as television, speakers or magnets.
Where there is a lot of movement or vibration, such as on a car dashboard or an
unstable shelf.
For safety
Do not attempt to disassemble this unit.
make sure that pins or other foreign objects to not get inside the Unit.
Take care not to drop the unit or subject it to strong shocks.
Note no listening with the earphones
listen at moderate volumes to avoid hearing damage.
Do not wear the earphones while driving or cycling. It may create a traffic hazard.
you should use extreme caution or temporarily discontinue use in potentially
hazardous situations such as walking, Jogging, etc.
If you hear no sound, DO NOT turn the volume up high because the music could
suddenly begin at high volume. To avoid hurting your ears or damaging the
headphones turn the volume control to the lowest level before starting playback
and slowly turn it up to the desired level.
LOCATION OF INDICATORS
1
IMP
A.PlayIndicator H. Minute/Second(Timer)
B.RecordingQualityIndicators Indicator
C. Message/Year Indicator I. REMAIN Indicator
D.REPEAT1/ALLIndicators J. R(Record)DATEIndicator
E.RecordIndicator K. VOXIndicator
F.BatteryIndicator L. MessageFileFolder
G.DateIndicator Indicators
B
Built-in Microphone 1 Mode /Pause 11
REV/FWDbutton 2,3 File/Time 12
REC/STOP button 4 Erase/Repeat 13
PLAY/STOPbutton 5 Holdknob 14
MIC/EAR(Earphone)Jack 6,7 Speaker 15
Record indicator 8 MIC sense knob 16
Volume 9 Vox(Voiceactivesystem) 17
LCD display(see next page) 10 Earphone 18
LOCATION OF CONTROLS
SAFETY PRECAUTIONS
3
2
1

6
5
4
7
BATTERY INSTALLATION
Open the battery compartment by sliding it out
andthenup.(the battery compartment
is designed to stay attached so it cannot
be lost).
.
NOTE:When replacing the batteries,the recorded messages will be saved,but the date
and time will have to be reset.
NOTE:When replacing the batteries,the recorded messages will be saved,but the date
and time will have to be reset.
SETTING THE TIME AND DATESETTING THE TIME AND DATE
When the batteries are inserted,0 hour and 0 min and Jan01 will appear in the display.SetWhen the batteries are inserted,0 hour and 0 min and Jan01 will appear in the display.Set
the time and date as follows:the time and date as follows:
2
REV FWD
PLAY/STOP
REC/
STOP
ERASE/REPEAT
1
3
1
2
REV FWD
PLAY/STOP
REC/
STOP
ERASE/REPEAT
TO TURN THE UNIT ON & OFF TO SWITCH BETWEEN MODES
POWER SOURCE OPERATION
(
CONTINUED
)
1 2 1 2
RECORDING QUALITY
You can choose between there voice recording quality modes. For best sound quality,
select HP(High play);for very good sound quality, select MP(Medium Play);for longer
recording time (reasonable sound quality),select LP(long Play).
SELECTING A FILE FOLDER
This unit has four memory storage areas(file folders)to choose from, labelled A,B,C and D.
You can store 99 messages in each individual file folder, for four file folder you can totally
save 396pcs of messages.
RECORDING SENSITIVITY HOLDSWITCH
Insert two 2pcs of”AAA”size batteries.(not
Included.)
following the polarity diagram.
3
Slide the battery compartment
back in place.
R
Y BATTERY INDICATORS:
The batteries are fresh.
The batteries are weak or dead,replace.
B
BATTERYPRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together(e.g.Alkaline and Carbon-zinc)or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged;they can overheat and rupture.(Follow battery
manufacturer’s directions.)
OPERATION
1 2
Press the PLAY/STOP button
1
to confirm
and the year will blink. Set the year using the
REV
2
and FWD
3
buttons, then press the
PLAY/STOP button
1
again to confirm.
While the date/time appears in the display,
press the FILE/TIME button
1
to shift
between 12 or 24 time display.
Press and hold the Mode/Pause button
2
for two seconds, then release, ’SET’ will
appear in the display. Press the
Mode/Pause button
2
once again to enter
the Date /Time set mode.
3
1
2
REV FWD
PLAY/STOP
REC/
STOP
ERASE/REPEAT
Set the Month using the REV
2
and FWD
3
buttons, then press the
PLAY/STOP button
1
again to confirm.
Repeat this step to set the Day, Hour and
Minute.
3
To turn the unit on, Press the
REC/STOP or PLAY/STOP
2
button. To
turn the unit off, simply do not touch any
button for 30 seconds, and the unit will
automatically turn off and show the time.
To enter the standby mode, press the
REC/STOP button or PLAY/STOP
button
2
while in the Time mode.The unit will
change to the Time mode if no button is
pressed in 30 seconds. To enter the Time
mode, press the MODE/PAUSE button
3
.while in the standby mode.
1
Press and hold the MODE/PAUSE button
1
for two seconds; “SET” will appear and
the recording quality will blink press the
REV
2
or FWD
3
button to select the
desired recording quality.
When the desired recording quality appears,
press the MODE/PAUSE button twice to
confirm and return to the Time
mode or it will change to the Time mode if no
button is pressed in 30 seconds.
High Play:..................................... 878 min.
Medium Play:............................... 1759 min .
Long Play:.....................................3369 min .
OPERATION
(
CONTINUED
)
1
Press the REC/STOP
1
or PLAY/STOP
2
button to enter the standby mode. Press the
FILE/TIME button
3
to select the desired
file folder (A,B,C,D).The number at the top
right of the display indicates the total
messages recorded. The number at the
bottom of the display will indicate the total
time recorded for the selected message.
NOTE:
Each time you record a message, The unit will
assign a number, counting up 1 from the last
message number, which will be shown on the
display.
If the unit is full, FULL will appear in the
display. Delete messages in this case.
1 2
Slide the MIC SENS switch to the
LOW position if recording sounds that are
close. Select the HIGH position if recording
sounds that are further away.
Slide the HOLD switch to the LOC
K
position
to disable the buttons; HOLD will appear in
the display. Slide the HOLD switch to the OFF
Position to enable the buttons again.

OPERATION
(
CONTINUED
)
OPERATION
(
CONTINUED
)
NORMAL RECORDING
8
9
10
11
This unit is capable of recording only when sound is heard. To use this feature, see the next page. For
normal recording, follow steps below.
NOTES:
NOTES:
. The built-in audio level automatically sets the recording level.. The built-in audio level automatically sets the recording level.
. To record another message, simply repeat step 3,the message number will increase by one.. To record another message, simply repeat step 3,the message number will increase by one.
. For normal voice levels, a distance of 5-9 inches is appropriate.. For normal voice levels, a distance of 5-9 inches is appropriate.
VOICE ACTIVATED (VOX)RECORDINGVOICE ACTIVATED (VOX)RECORDING
Voice activated recording will allow dictation only when you speak.Voice activated recording will allow dictation only when you speak.
When the unit detects a pause of a few seconds, it will temporarily stop recording until it detects sound
again.
When the unit detects a pause of a few seconds, it will temporarily stop recording until it detects sound
again.
TO PLAY BACK MESSAGESTO PLAY BACK MESSAGES
TO REPEATEDLY PLAY BACK MESSAGES TO REPEATEDLY PLAY BACK MESSAGES
You can set the unit to repeat1 or all messages as follows:You can set the unit to repeat1 or all messages as follows:
TO CANCEL REPEAT PLAYBACK:TO CANCEL REPEAT PLAYBACK:
To cancel repeat playback, press the ERASE/REPEAT button once or twice until the REPEAT indicator
disappears from the display.
To cancel repeat playback, press the ERASE/REPEAT button once or twice until the REPEAT indicator
disappears from the display.
TO PAUSE A MESSAGETO PAUSE A MESSAGE
1
2
Make sure the VOX switch on the
side of unit is set to OFF. Turn the
unit on, and select the desired sound
quality as described on page 6.
Select a File Folder by pressing the FILE/TIME
button (see page7).
3
4
Press the PLAY/STOP button
1
to see the
remaining recording time during recording. To pause
recording ,press the MODE/PAUSE
button
2
;PAUSE will blink in the display. To release
pause press the MODE/PAUSE button
2
again.
While in the standby mode, press the
REC/STOP button and the REC indicator will light
and the elapsed time will appear.
Speak into the built-in microphone or insert a
microphone into the MIC jack and speak to it with a
normal toneof voice. Press the REC /STOPbutton
again to stop recording.
OPERATION
(
CONTINUED
)
1
2
Slide the VOX switch on the side of the
unit to the ON position. Turn the unit
on,and select the descried sound quality
as described on page 6.
Select a FILE Folder by pressing the
FILE/TIME button(see page7).
3
Press the REC/STOP button andthe REC
indicator will light and the elapsed time will appear.
Speak intothe built-in microphone or insert a
micro-phone into the MIC jack and when the unit
picks up sound, it will record. When not
recording ,the REC indicator will blink and
PAUSE will blink in the display until sound is
detected.
Press the REC/STOP button again to stop
recording.
NOTES:
.The first few sounds activate the recorder
and may not be recorded.
. Avariation in voice level
during recording will not
stop the unit. two seconds of silence is
required to stop the recording.
. For constant recording, see previous page.
.To pause, press the MODE/PAUSE
.The built-in audio level automatically sets the
recording level.
. For normal voice levels, a distance of 5-9
inches is appropriate.
1
2
Turn the unit on and select a File
Folder by pressing the FILE/TIME
button(see page7).
Select the desired message number by pressing
the REV
1
or FWD
2
button; the message number and the message
len
g
th will a
pp
ear in the dis
p
la
y
.
3
While in the standby mode, press the
PLAY/STOP button
1
; the unit will play
the currently selected message, then
stop. During playback,
the play indicator and the elapsed time of
the message will appear in the display.
You can check the message recording
time and date by pressing the
REC/STOP button
2
.
NOTES:
.To pause, press the MODE/ PAUSE
button; PAUSE will blink in the display. To
release pause, press the MODE/PAUSE
button again.
. For Clue and Review during playback,
simply press and hold the desired REV or
FWD button.
A chattering sound will be heard.
Release the button when the desired point
is reached.
.To skip or go back messages, simply press
and release the desired REV or FWD button
until the desired message number is
reached.
EARHONE JACK
For private listening, connect an earphone (not included) to this jack.
The speaker is automatically disconnected when the earphone plug is inserted in the jack.
OPERATION
(
CONTINUED
)
1
2
REPEAT MESSAGE: While playing back a
message, press the ERASE/REPEAT
button
1
once, “REPEAT” will appear in the
display and the message playing
will repeat over and over until the
PLAY/STOP button
2
is pressed.
REPEAT All MESSAGES: While Playing
back a message, press the ERASE/REPEAT
button
1
twice; “REPEATALL” will appear in
the display and all messages in the selected
file folder will repeat over and over until the
PLAY/STOP button
2
is pressed.
1
2
To pause Recording or playback,
press the MODE/PAUSE button;
PAUSE will blink in the display.
Press the MODE/PAUSE button
again to resume recording or
playback.

12
13
14
SCAN PLAYBACK
This unit can play back the first five seconds of each recorded message,
which is useful in locating a particular recording.
ERASING A SINGLE MESSAGES
While in the standby mode, select the
desired file folder using the FILE/TIME
button
1
, and the desired message to delete
using the REV
2
or FWD button
3
;
the message number and the message length
will appear in the display.
ERASING ALL MESSAGES IN THE 4 FILE FOLDERS
IMPORTANT NOTES:
.Once message(s)are deleted, they cannot be recovered.
.When the memory is full, Full will appear in the display.
OPERATION
(
CONTINUED
)
SPECIFICATIONS
Recording System……………...................................................Built-in Flash Memory
Recording time…………………………………………………..3369 minutes in LP mode
Speaker………………………………………………………………………….0.2W(8 Ohm)
Output Power…………………………………………………………………………..80mW
Power Source…………………………..3V, “AAA” size×2 batteries(Not Included)
Battery life..........................................Approx 10 hours at recording mode
5 hours at play mode at volume level Max.
Dimensions........................................................................106(H)×36(W)×17(D)mm
Weight....................................................................................50g(without batteries)
Specifications are subject to change without notice.
1
2
While in the standby mode,
select the file folder(A,B,C,D) using the
FILE/TIME button
1
,Press and hold the
PLAY/STOP button
2
for 2 seconds; SCAN
will appear in the display. The unit will
appear in the display. The unit will
automatically scan and play the first five
seconds of each message in the selected
file folder, starting at message one.
The unit will automatically stop after all
Messages have been played. To
playback the message during
scanning, press the change to
playback mode. To stop scan
playback,
Press the PLAY/STOP button twice.
While in the standby mode, press and hold
the ERASE/REPEAT button
1
first, then
press and hold the REC/STOP button
2
for
two seconds; ALL and ERASE will blink in
the display.
To erase all messages, press the
ERASE/REPEAT button again within 5
seconds. If the ERASE button is not pressed
again within the first 5 seconds, the messages
will not erase.
OPERATION
(
CONTINUED
)
1
2
1
2
Press the ERASE/REPEAT button; ERASE will
appear in the display and the first 5 seconds of
the message will play. To erase, press the
ERASE/REPEAT button within the 5 seconds it
is playing and the rest of the messages will be
renumbered. If you do not want to erase, do
not press the ERASE/REPEAT button while it
is playing.