mpw MI-3120 User manual
Warning
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that
this device does not cause harmful interference (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
The antennas used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located for operating in conjunction with any
other antenna or transmitter.
FCC ID: 2AZO6MI-3021
CE RED
This product can be used across EU member states.
RF Specification:
EU Declaration of Conformity
We,
Shenzhen Baishihao Electronic Technology Co., Ltd. (Room 202, No. 6, 5th Alley, Xiangjiaotang
New Village, Xiangjiaotang Community, Bantian Street, Longgang District, Shenzhen
District,Shenzhen,China,518057) hereby declares that this Outdoor Bullet Cam is in compliance
with the essential requirements and other relevant provisions of Directive 2014/53/EU.
According to Article 10(2) of Directive 2014/53/EU, the Outdoor Bullet Cam can be used in
Europe without restriction.
Warning:
1. Adapter shall be installed near the equipment and shall be easily accessible.
2. Operation temperature:-10~50℃.
3. The plug considered as disconnect device of adapter.
4. Accessories information:
Adapter JF012WR-1200100VH
Input: 100-240V~50/60Hz 0.35A
Output: 12V1.0A
We,
According to Article 10(2) of Directive 2014/53/EU, the MI-3021 can be used in Europe without
restriction.
The full text of the EU declaration DOC is available at the following:
Visit the Web site https://www.mpwsafe.com
Function Max RF
Output Power LimitOperation Frequency
Wi-Fi 13.75 dBm 20 dBm
802.11b/g/n(20MHz):
2412~2472MHz;
802.11n(40MHz):2422~246
2MHzt
P. 1
P. 2
P. 3
P. 4
P. 5
P. 6-10
P. 11
P. 12
Catalogue
1. What’s In The Box
2. Camera Structure
3. Insert Micro SD Card
4. Read Before Installing
5. Set Up With SafeMiraie App
6. Installation
7. Status Light
8. Protect Plan
What’s In The Box
Quick Guide
Drilling Template
X 3
X 3
Mounting Screws Anchors Outdoor Bullet Cam
Power Adapter
Weatherproof Tube
Outdoor Bullet Cam
Yourproperty guardian at day and night
1
Infrared LEDs Antenna
Light Sensor
Lens
Wi-Fi
Configuration
Button
Ethernet Cable Port
Power Port
Status Light
Speaker
Microphone
Micro SD Card Slot
Camera Structure
2
Insert Micro SD Card
This camera comes with a built-in card slot which supports up to 128GB Micro
SD card. Once you insert the storage card, the camera will automatically start to
record and store videos on the storage card. You can view those videos in the
‘Replay’ page by clicking the ‘Replay’ button in the ‘Homepage’.
Step 1: Loosen the screws. Take off the cover gently since wires are attaching to it.
Step 2: Insert Micro SD card. Make sure you insert it in the correct direction.
Step 3: Put the cover back and tighten the screws.
3
Micro SD
Card Slot
1
3
2
1. Keep the Outdoor Bullet Cam and all accessories out of reach of children and pets.
2. Power supply voltage that is required to operate Outdoor Bullet Cam
should be DC12V (≥1000mA).
3. The product can only be used in proper temperature and humidity:
Operating temperature: -10°C - 50°C (14°F-122°F)
Operating humidity: 0-95%.
4. Please do not expose the camera lens to direct sunlight.
5. Please do not install the camera to the place that is likely struck by
lightning.
Read Before Installing
Note:
1. This camera only works with 2.4GHz Wi-Fi.
2. Strong lights may interfere with the ability to scan the QR code.
3. Avoid placing the device behind furniture or near microwaves.
Try to keep it within range of your Wi-Fi signal.
4
Set Up with SafeMiraie App
Download the SafeMiraie App from App Store or Google
Play. Follow the in-app instruction to complete the entire
set up process.
5
Check following things before you starting to drill holes on your wall:
1. This camera has been successfully added to your Safemiraie App and is
able to stream video.
2. Have planned the cable route. Measured the length of the power cable
and ethernet cable (if you plan to use ethernet connection) you will need.
Installation
Step 1:
Find a good installation spot.
We recommend installing the Outdoor Bullet Cam just 7-10 feet (2-3
meter) above the ground for a better two-way audio experience.
There is a power outlet nearby.
Test whether Outdoor Bullet Cam can stream video smoothly at the spot.
Make sure nothing blocks the camera’s sight.
6
Step 2:
Before you start to drill, make sure you know the locations of wall-in
pipes and electrical wires. (If you are not comfortable with drilling holes,
please consult with a licensed electrician)
①Use the provided drilling template to mark the position of holes on
your wall. Use drill bit (15/64", 6mm) to drill three holes.
②Install anchors to hold screws.
Skip ①② if you are installing camera on wood.
7
1 2
3
③Tighten the provided screws to secure the camera.
8
13
2
Outdoor Bullet Cam
Ethernet Cable Port
Ethernet Cable
(Not included)
Weatherproof Tube
Step 3 (Wired Connection):
Read this step if you are using wired connection, otherwise skip this step.
Aweatherproof tube is needed for Ethernet Cable to avoid leaking water into
Ethernet Cable Port.
Make sure the cable works. Insert the cable into the weatherproof tube, and then
connect it to the Ethernet cable port of your Camera.
Things you need:
Ethernet Cable
9
Step 4:
Screw the plastic flange-nut counterclockwise over the base of the camera,
point the camera to your designate direction, then screw the plastic the
plastic flange-nut.
360°
360°
90°
10
DescriptionStatus Light
Solid Green
Rapidly Flashing green
None
Online
Wi-Fi Configuration Mode
Offline
This camera uses status light to communicate.
Status Light
11
Protect Plan provides optional advanced features for home security, and
supports multiple devices.
Continuous Video Recording: Records what's happening for 24/7 and saves
everything in the background, you can replay to catch anything you missed.
Event Video Recording: Automatically records a video clip when a motion is
detected, and push it to your phone instantly.
Human Detection: Get alerted when human are detected. No more
bothered by normal alerts, and won't miss important things.
12
Protect Plan
Visit my.safemiraie.com to learn more.
Feel free to contact us for additional help
Room 202, No. 6, 5th Alley, Xiangjiaotang New Village,
Xiangjiaotang Community, Bantian Street,
Longgang District, Shenzhen, China, 518057
Shenzhen Baishihao Electronic Technology Co., Ltd.
www.mpwsafe.com
Table of contents
