Vicon Roughneck V2000D-PTZ User manual

Quick Guide
Roughneck V2000D-PTZ
Outdoor Vandal PTZ Dome Camera
XX320-20-01
Cybersecurity Notification: All network connected devices should use best practices for
accessing the device. To that end, these network cameras do not have a default password. A user defined
password with minimum password strength requirements must be set to access the device. See page 14 of
this Quick Guide for set-up instructions.
Vicon Industries Inc. does not warrant that the functions contained in this equipment will
meet your requirements or that the operation will be entirely error free or perform precisely as
described in the documentation. This system has not been designed to be used in
life-critical situations and must not be used for this purpose.
Document Number: 8009-8320-20-01 Product specifications subject to change without notice.
Issued: 2/2021 Copyright © 2021 Vicon Industries Inc. All rights reserved.
Vicon Industries Inc.
Tel: [phone]) Fax: [phone]
Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON
(800-348-4266)
UK: 44/(0) 1489-566300
www.vicon-security.com

V2002D-PTZ | Quick Guide
1
Table of Content
1Product Overview 4
1.1 Physical Characteristics 4
2Installation and Mounting 8
2.1 Package Content 8
2.2 Installation 8
2.2.1 Checking Appearance 8
2.2.2 Inserting or Removing the SD Card 9
2.2.3 Installing the Camera with Wall Mount 9
2.2.4 Connecting the Cables 11
3Connection 13
3.1 Network Topology 13
3.2 System Requirements 13
3.3 Connecting Process 14
3.3.1 Default IP address 14
3.3.2 Connecting from a computer & Viewing Preparation 14
3.4 IP Toolbox 18

V2002D-PTZ | Quick Guide
2
WARNING
⚫This camera operates at 24 VAC/ 48 VDC / PoE (IEEE 802.3bt Class 6).
⚫Installation and service should be performed only by qualified and experienced technicians and comply
with all local codes and rules to maintain your warranty.
⚫We are NOT liable of any damage arising either directly or indirectly from inappropriate installation which
is not depicted within this documentation.
⚫To reduce the risk of fire or electric shock, do not expose the product to rain or moisture.
⚫Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and
wipe with a dry soft cloth.
⚫Do not apply benzene or thinner to the camera, which may cause the surface to be melted or lens fogged.
⚫Avoid aligning the lens with extremely bright objects (e.g., light fixtures) for long periods of time.
⚫Although this camera is waterproof and suitable for both indoor and outdoor usages, please do not sink
the camera into water. Contact your dealer in case of sunk.
⚫Avoid operating or storing the camera in the following locations:
Extremely humid, dusty, or hot/cold environments (recommended operating temperature:
-40°F to +140°F/--40°C to +60°C)
Close to sources of powerful radio or TV transmitters
Close to fluorescent lamps or objects with reflections
Under unstable or flickering light sources
Get Started
This quick guide is designed as a reference for installation of the camera. For additional information on the
camera’s features, functions, and detailed explanation of the web interface controls, refer to User’s Manual for
details. Please read this quick guide thoroughly and save it for future use before attempting to install the
camera. From this guide you will get:
⚫Product Overview: The physical parts, features and dimensions of the camera.
⚫Installation and Connection: The instructions on installation and wires connection for the camera.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable
local laws, regulations, and procedures.

V2002D-PTZ | Quick Guide
3
FCC Compliance Statement
Information to the user: This unit has been tested and found to comply with the limits for a Class
B digital device pursuant to Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This unit generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the manual, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this unit does cause harmful interference to radio or television reception, which can be determined by
turning the unit off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
⚫Reorient or relocate the receiving antenna.
⚫Increase the separation between the unit and receiver.
⚫Connect the unit to an outlet on a circuit different from that to which the receiver is connected.
⚫Consult the dealer or an experienced radio/TV technician for help.
Caution
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the unit.
CE Statement
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation. The manufacturer declares that the unit supplied with this
guide is compliant with the essential protection requirements of EMC directive and General Product Safety
Directive GPSD conforming to requirements of standards EN55022 for emission, EN 50130-4 for immunity,
EN 300 and EN 328 for WIFI.
The camera Is IP66 and IK7 rated. It also meets regulations required to be NDAA, GSA schedule and TAA
approved.

V2002D-PTZ | Quick Guide
1Product Overview
1.1 Physical Characteristics
Figure 1 - 1: Physical Dimensions
Unit: mm (in.)

V2002D-PTZ | Quick Guide
5
No
Description
1
Camera 1-1/2” NPT pendant adapter
2
Screws (x2) to open and lock camera top cover
3
Camera top cover
4
Camera lens
5
Camera head
Table 1 - 1: Parts Pictorial Index Description
Definition
Figure 1 - 2: Parts Pictorial Index

V2002D-PTZ | Quick Guide
6
Figure 1 - 3: Internal Interface Pictorial Index
No.
Name
Description
1
Activity
Behaviors
Booting: Fast flashing green LED indicates the camera is currently
booting.
Software updating: Alternating fast/slow flashing green LED
indicates the camera is updating software.
Booting failure: A slower flashing green LED indicates the camera
failed to boot.
Booting completion: When the green light is off, the LED indicates
the camera has completed booting.
2
RJ-45 Network
Port
Connect the RJ-45 connector to this port with a PoE (Class 6)
compatible network device that supplies power through the Ethernet
cable.
3
Power Terminal
The port is used to connect with external either 24 VAC or 48 VDC
power supply.
4
Default Button
Default: Press the button for 5 seconds to restore the camera settings
to factory default.
5
Reset Button
Reset: Press the button for approximately 1 second to reboot the
camera.
1
2
3
4
5
6

V2002D-PTZ | Quick Guide
7
Table 1 - 2: Internal Interface Index Description
6
DI/DO Port
DI/DO (Digital Input/Output) ports are equipped for external devices,
e.g., smoke detector, siren, microphone.
•Alarm In: Via “GND” and “Alarm In” ports, connect to
external device that can trigger alarm input signals.
•Alarm Out: Via “COM” and “Alarm Out” ports,
connect to external device to be triggered through alarm
output signals.
•Audio In: Via “GND” and “Audio In” ports, connect to external
device such as microphone that receives sound for camera.
•Audio Out: Via “GND” and “Audio Out” ports, connect to
device such as speaker to be triggered through alarm output
signals.

2Installation and Mounting
2.1 Package Content
Check if all items listed below are included in the packing box.
⚫IR PTZ Speed Dome * 1
⚫Adapter Ring * 1
⚫T20 torx wrench * 1
⚫T6 torx wrench * 1
⚫T20 Stop Screw * 3
⚫12-pin Terminal connector for I/O function * 1
⚫2-pin Terminal block * 1
⚫Printed Quick Guide * 1
2.2 Installation
The following tools may be helpful to complete the installation:
⚫Drill
⚫Screwdrivers
⚫Wire cutters
2.2.1 Checking Appearance
When unpacking, check to see if there is any visible damage to the appearance of the camera and its
accessories. The protective materials used for the packaging should protect the camera from most accidents
during shipment. Remove the protective materials from the camera after every item is properly checked in
accordance with the list in Package Contents..

V2002D-PTZ | Quick Guide
9
2.2.2 Inserting or Removing the SD Card
1. Remove the two screws (1) located on the micro SD card cover.
Carefully pull open the micro SD card cover and insert or remove the micro SD card into or from the
camera.
Figure 2 - 1: Inserting or Removing The Micro SD Card
2.2.3 Installing the Camera with Wall Mount
1. Based on your need, make sure that all cables have been passed through the wall mount and the
pendant adapter. Use waterproof tape to wrap the thread of pendant adapter and then lock the pendant
adapter on the wall mount.
Figure 2 - 2: Locking the Pendant Adapter

V2002D-PTZ | Quick Guide
10
2. Let the cables pass through the rubber sealing ring, and then mount the sealing ring on IR speed dome.
Then mount the IR PTZ speed dome camera on the pendant adapter.
Figure 2 - 3: Mounting The Camera
3. Fasten the 3 T20 stop screws with the T20 torx wrench.
Figure 2 - 4: Fastening the 3 T20 Stop Screws
Sealing Ring

V2002D-PTZ | Quick Guide
11
2.2.4 Connecting the Cables
1. Loosen the 2 T20 screws on top cover with the T20 torx wrench and then carefully allow the camera
body shift downward.
Figure 2 - 5: Loosening the 2 T20 Screws on Top Cover
With the camera body shifted downward, the I/O interfaces will be seen on the back of the camera module.
Make the appropriate cable connections
2. Based on your needs, connect the power cable to the power port via one of the following 3 options.
24 VAC: Connect a power cable that supplies 24 VAC power source to the power terminal.
48 VDC: Connect a power cable that supplies 48 VDC power source to the power terminal.
NOTE: The polarities should match when using 48 VDC power source.
PoE (Class 6): Connect an Ethernet cable terminated with a RJ-45 connector to the PoE RJ-45 port
for both power supply and network connectivity.
3. Insert audio in/out cables and alarm in/out cables to the corresponding terminals of the camera if required.
NOTE: It is recommended to connect external microphones to ground (GND) on the digital I/O connector.
4. Refer to Figure 1 - 3: Internal Interface Pictorial Index for details on I/O interface.

V2002D-PTZ | Quick Guide
12
Figure 2 - 6: Connecting the Cables
5. After connecting the cables, shift the camera body upward and then tighten the 2 T20 screws on top
cover with T20 torx wrench to complete the installation of the camera with wall mount.
Figure 2 - 7: Completing the Camera Installation

V2002D-PTZ | Quick Guide
13
3Connection
3.1 Network Topology
The camera, which is equipped with Ethernet RJ-45 network interface, can deliver live view image in real time
via both Internet and Intranet manners. Please refer to the skeleton drawings shown below for understanding.
Figure 3 - 1: Network Topology
3.2 System Requirements
The table below lists the minimum requirements to implement and operate the camera. It is recommended not
to use any hardware/software component below these requirements for proper performance.
Table 3 - 1: System Requirements
System Hardware
CPU
i5-2430M CPU@ 2.40GHZ 2.40GHZ
RAM
6 GB or above
Display
NVIDIA GeForce 6 Series or ATI Mobility Radeon 9500
System Software
Operating System
Windows 7 SP1, Windows 8, Windows 10
Browser
Internet Explorer 11, Mozilla Firefox, Chrome, Safari, Microsoft Edge
Unit
Power Supply
24 VAC/48 VDC/PoE (IEEE 802.3bt Class 6)
Networking
Wired*
10/100BASE-T Ethernet (RJ-45 connector)
*A switch is required for surveillance on multiple cameras.
Note
All the installation and operations should comply with your local electricity safety regulations.
Caution
When using PoE, this camera is to be connected only to PoE networks without routing to any
heterogeneous devices. A heterogeneous network is a network connecting computers and
other devices where the operating systems and protocols have significant differences.

V2002D-PTZ | Quick Guide
14
3.3 Connecting Process
3.3.1 Default IP address
Since this is a network-based camera, an IP address must be assigned. The camera’s default IP address is
obtained automatically through a DHCP server in your network; be sure to enable DHCP in "Network
Settings." If DHCP is not available, the camera will use APIPA (link-local address); IPv4 link-local addresses
are assigned from address block 169.254.0.0/16 (169.254.0.0 through 169.254.255.255).
3.3.2 Connecting from a Computer & Viewing Preparation
Connecting from a computer
1. Make sure the camera and your computer are in the same subnet.
2. Check whether the network available between the camera and the computer by executing ping the
default IP address. To do this, simply start a command prompt (Windows: from the “Start Menu”, select
“Program”. Then select “Accessories” and choose “Command Prompt”), and type “Ping” and then type in
your IP address. If the message “Reply from…” appears, it means the connection is available.
3. Start a browser e.g., Internet Explorer and enter IP address. A login window as shown below should pop
up. In the window, enter the default user name: ADMIN; it is required to change the password when you
login for the first time for added security, which requires at least 8 characters including 1 uppercase letter,
1 special character, alphanumeric characters to log in.
4. Further administration on the unit can be found in “User Manual".
Figure 3 - 2: Login Window

V2002D-PTZ | Quick Guide
15
Viewing Preparation
Images of the unit can be viewed through various browsers. Before viewing, follow these steps to enable the
display.
1. Enable Cookies as instructions below
In Internet Explorer, click Internet Options on the Tools menu.
On the Privacy tab, move the settings slider to Low or Accept All Cookies.
Click OK.
2. When a proxy server is used, click Internet Options on the Tools menus of Internet Explorer, select
Connect tab, click LAN button, and set proxy server.
3. Change Security in Internet options as instructions below
On tool menu, click Internet Options.
Press the Security tab.
If the camera operates inside of the intranet, click the Intranet icon.
If the camera operates outside of the intranet, click the Internet icon.
Click Custom Level. This will open the Security Settings – Internet Zone screen.
Figure 3 - 3: Security Settings 1/4

V2002D-PTZ | Quick Guide
16
Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:
【Download signed ActiveX controls】➔ Prompt (recommended)
【Download unsigned ActiveX controls】➔ Prompt
【Initialize and script ActiveX not marked as safe for scripting】➔ Prompt
Figure 3 - 4: Security Settings 2/4
【Automatic prompting for ActiveX controls】➔ Enable
Figure 3 - 5: Security Settings 3/4

V2002D-PTZ | Quick Guide
17
【Run ActiveX controls and plug-ins】➔ Enable
【Script ActiveX controls marked safe for scripting*】➔ Enable
Figure 3 - 6: Security Settings 4/4
Press OK to save the settings.
Close all the browser windows and restart the browser. This will allow the new settings taking effect.
Type your IP address into the browser.
You should be able to see the camera image screen.

V2002D-PTZ | Quick Guide
18
3.4 IP Toolbox
IP Toolbox is a utility program that helps users to locate the camera(s) in local area network that computer is
connected to. Please note that IP Toolbox works only in Microsoft Windows XP, Microsoft Windows Vista, and
Microsoft Windows 7 or above. Steps to get the utility program running are listed below.
1. Download the IP Toolbox’s folder to local computer. The latest IP Toolbox can be found on Vicon’s
website Camera Software Download page, vicon-security.com.
2. Double click on IPToolbox.exe in the IP Toolbox’s folder, and the IP Toolbox window should pop out as
below.
Figure 3 - 7: IP Toolbox
3. The window lists information of camera(s) in operation at the present time. Click the camera in the list for
which you want to configure the network settings.
4. Configure the following settings as needed.
▪User Name & Password: Before performing any operation to any listed camera, please enter username
and password for the selected camera, and then click “Verify” for authentication purposes.
▪Camera Name: Enter a descriptive name for the camera.
▪Network Settings: If you have a DHCP server on your network to assign IP addresses to network
devices, enable the “dhcp” option from dropdown menu of IP MODE. Otherwise, select “manual” to
manually enter the values for IP Address, Subnet Mask, Gateway and HTTP Port fields.
▪Click “Save” to enable the settings. Click “Cancel” to discard the settings.
5. Press “View” button; the designated browser page of the selected camera will pop out. Please input
the corresponding User Name & Password to log in to the specific page of camera.
6. Press “Refresh” button; all the cameras currently connected to the network will appear on the list.
7. Press “Initialize” button; there are three options, Software default, Hardware default, and Reboot
camera, for user to perform the factory default or reboot the camera. After clicking the preferred item, the
warning message will appear. Please confirm again before you perform the selected function.

V2002D-PTZ | Quick Guide
19
8. The “Filter” button on the upper-right corner allows user to perform filtering search, which means you can
input certain keywords into the field nearby and also narrow down the range by selecting the criteria from
the dropdown menu for a target search on cameras connected.
9. Press “Auto Set IP Address” button to automatically give each camera an IP address from
predefined range and connected to predefined network internet controller.
▪User Name & Password: Enter username and password for the current auto set IP address setting.
▪Network Interface Controller: Select desired network interface controller that each camera(s) will be
connected to, and also select the IP address and IP address range of the controller.
Figure 3 - 8: Auto Set IP Address