EverFocus EPTZ9200 Series User manual

EPTZ9200/9300 Series Speed Dome
AHD 1080p Outdoor/Indoor PTZ
with True Day/Night and WDR (20x / 30x Optical Zoom)
Quick Installation Guide
Copyright © EverFocus Electronics Corp.
Release Date: November, 2015

EPTZ9200/9300 Series
1
1. Overview
The EPTZ9200/9300 Series comes in two types: outdoor (EPTZ9200/9300) and indoor (EPTZ9200i/9300i).
1
2
3
1
2
3
Outdoor
(EPTZ9200/9300)
Indoor
(EPTZ9200i/9300i)
Item Name
No. Item Name No. Item Name No. Item Name
1 Top Housing 2 Outer Housing 3 Camera Main Body
Packing List
There are 3 boxes that are camera main body with a camera module, top housing with a base board & pin
connector and outer housing with bubble, plus one tool packet in the package. The detail accessories are
listed below:
Standard
1. Camera Main Body x 1
2. Top Housing x1
3. Outer Housing with Bubble x1
4. Tool Packet
Hexagon Wrench x1
Glove x 1 Pair
RS-485 Terminal Block
Desiccant Packs x 3
Note:
1.
Equipment configurations and supplied accessories vary by country. Please consult your local
EverFocus office or agents for more information. Please also keep the shipping carton for possible
future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.

EPTZ9200/9300 Series
2
2. Cables and I/O Terminal Block
Cable Descriptions
Power Cable
An adapter with 24 VAC~ / 3A output provides the power to the EPTZ9200/9300 Series camera. An
extension power line may be needed.
Note:
Different regions may use different ranges for AC voltage. Be sure to check the voltage range in your
area before installing.
Video Cable
A BNC cable is used for connecting an EPTZ9200/9300 Series to a DVR or a monitor. An amplifier may be
needed depending on the distance.
RS-485 Cable
The yellow wire carries RS-485+, and the orange wire carries RS-485-. Connect these wires to the EKB500 or
other control device in order to control the PTZ camera.
I/O Terminal Block
The base board that is inside the top housing connects to power cable, video cable, control cable, alarm
cable and fan. The housing must be removed in order to properly connect the cables. The connectors of
cable names are marked on the board in white text.
There are 4 alarm inputs and 2 alarm outputs available, represented by Pin 1~12. Pin 13 and 14 are video
pins for connecting to video cable. Pin15~16 are RS-485 pin for connecting to keyboard. Pin 17 and 18 are
power pin for connecting to 24 VAC~ po wer.
Orange RS485
-
24VAC~
(POWER)
VIDEO
Yellow RS485+

EPTZ9200/9300 Series
3
1-12 Alarm
13-14
Video
15-16
RS485
17-18
24VAC~
EPTZ9200/9300 Series Base Board
Pin Function Pin Function
1 ALM_NO_B (Alarm Output Normal Open B) 10 ALMIN3 (Alarm Input 3)
2 ALM_COM_B (Alarm Output Common B) 11 GND (Ground)
3 ALM_NC_B (Alarm Output Normal Close B) 12 ALMIN4 (Alarm Input 4)
4 ALM_NO_A (Alarm Output Normal Open A) 13 VIDEO+
5 ALM_COM_A (Alarm Output Common A) 14 VIDEO-
6 ALM_NC_A (Alarm Output Normal Close A) 15 RS-485-
7 ALMIN1 (Alarm Input 1) 16 RS-485+
8 GND (Ground) 17 AC24A+
9 ALMIN2 (Alarm Input 2) 18 AC24B-

EPTZ9200/9300 Series
4
3. Optional Accessories
•EPTZ- PBOX (External power connection box)
& adaptor
•Wall mount bracket
•Pole mount adapter
(Used for installing a wall-mount bracket to a
pole, indoors or outdoors.)
•Corner mount adapter
(Used for fixing a wall-mount bracket to a
90° wall corner, indoors or outdoors.)
•Indoor ceiling pendant mount bracket &
adaptor (Used for installing a speed dome
against a ceiling.)
•Indoor concrete ceiling mount adapter
(Used for attaching a speed dome to a
concrete ceiling.)
•Outdoor sunshield
•Indoor in-ceiling mount bracket
•EKB500 (RS-485 Keyboard) •EKB200 (USB controller keyboard)

EPTZ9200/9300 Series
5
4. Installation
Replacing the Desiccant Bags
Before installing, replace the 3 desiccant bags inside the top housing. The desiccant bag loses its
effectiveness after you open the camera. To keep the camera’s interior dry, it is highly recommended to
replace the desiccant bags every time when you open the camera.
To replace the desiccant bags:
1. On the Top Housing, slightly press the black plastic socket backward and lift up the base board.
2. Remove the desiccant bags from the top housing.
3. Stick the supplied 3 new desiccant bags inside the top housing. Place back the base board.
Note: Ensure Not to place the desiccant bags under the position of the fan.
Fan
4. Insert the base board into the black plastic socket. The base board should click firmly into position.
Make sure the pin connector on the base board is lined up with the pin connector on the main body
when you press the two together.

EPTZ9200/9300 Series
6
Initial Setup
To allow the control device, such as a keyboard, to recognize and then control multiple cameras, you need
to set up the ID address for the cameras using the DIP switch on the Camera Main Body. You can also set up
the Protocol, Baud Rate and Video Output Format for the cameras.
Note: Please ensure to turn off the power when setting up the DIP Switch. The new values will only take
effect after restarting the camera.
DIP Switch
Camera Main Body
ID Address
The ID address of the camera should be set to correspond properly with the control device, such as a
keyboard. The eight switches on the right correspond with the binary code of the ID address, allowing up to
256 ID addresses (0 ~ 255) to be set up. Please refer to the sticker on the camera main body or the
following diagram for setting up the ID address. The default ID address is 1.
DIP Switch
Sticker on the Camera Main Body

EPTZ9200/9300 Series
7
ON
12345678
Switch Address
1
ON
12345678 2
ON
12345678 3
ON
12345678 4
ON
12345678 5
ON
12345678 6
ON
12345678 7
ON
12345678 8
ON
12345678 9
ON
12345678 10
ON
12345678 11
ON
12345678 12
ON
12345678
Switch Address
13
ON
12345678 14
ON
12345678 15
ON
12345678 16
ON
12345678 17
ON
12345678 18
ON
12345678 19
ON
12345678 20
ON
12345678 21
ON
12345678 22
ON
12345678 23
ON
12345678 24
ON
12345678 25
ON
12345678 26
ON
12345678 27
ON
12345678 28
ON
12345678 29
ON
12345678 30
ON
12345678 31
ON
12345678
Switch Address
33
ON
12345678 34
ON
12345678 35
ON
12345678 36
ON
12345678 37
ON
12345678 38
ON
12345678 39
ON
12345678 40
ON
12345678 41
ON
12345678 42
ON
12345678 43
ON
12345678 44
ON
12345678 45
ON
12345678 46
ON
12345678 47
ON
12345678 48
ON
12345678 49
ON
12345678 50
ON
12345678 51
ON
12345678 52
ON
12345678 53
ON
12345678 54
ON
12345678 55
ON
12345678 56
ON
12345678 57
ON
12345678 58
ON
12345678 59
ON
12345678 60
ON
12345678 61
ON
12345678 62
ON
12345678 63
Switch Address Switch AddressSwitch AddressSwitch Address Switch AddressSwitch Address
ON
12345678
Switch Address
65
ON
12345678 66
ON
12345678 67
ON
12345678 68
ON
12345678 69
ON
12345678 70
ON
12345678 71
ON
12345678 72
ON
12345678 73
ON
12345678 74
ON
12345678 75
ON
12345678 76
ON
12345678
Switch Address
77
ON
12345678 78
ON
12345678 79
ON
12345678 80
ON
12345678 81
ON
12345678 82
ON
12345678 83
ON
12345678 84
ON
12345678 85
ON
12345678 86
ON
12345678 87
ON
12345678 88
ON
12345678 89
ON
12345678 90
ON
12345678 91
ON
12345678 92
ON
12345678 93
ON
12345678 94
ON
12345678 95
ON
12345678
Switch Address
97
ON
12345678 98
ON
12345678 99
ON
12345678 100
ON
12345678 101
ON
12345678 102
ON
12345678 103
ON
12345678 104
ON
12345678 105
ON
12345678 106
ON
12345678 107
ON
12345678 108
ON
12345678 109
ON
12345678 110
ON
12345678 111
ON
12345678 112
ON
12345678 113
ON
12345678 114
ON
12345678 115
ON
12345678 116
ON
12345678 117
ON
12345678 118
ON
12345678 119
ON
12345678 120
ON
12345678 121
ON
12345678 122
ON
12345678 123
ON
12345678 124
ON
12345678 125
ON
12345678 126
ON
12345678 127
Switch Address
ON
12345678 0
ON
12345678 32
ON
12345678 64
ON
12345678 96

EPTZ9200/9300 Series
8
ON
12345678
Switch Address
129
ON
12345678 130
ON
12345678 131
ON
12345678 132
ON
12345678 133
ON
12345678 134
ON
12345678 135
ON
12345678 136
ON
12345678 137
ON
12345678 138
ON
12345678 139
ON
12345678 140
ON
12345678
Switch Address
141
ON
12345678 142
ON
12345678 143
ON
12345678 144
ON
12345678 145
ON
12345678 146
ON
12345678 147
ON
12345678 148
ON
12345678 149
ON
12345678 150
ON
12345678 151
ON
12345678 152
ON
12345678 153
ON
12345678 154
ON
12345678 155
ON
12345678 156
ON
12345678 157
ON
12345678 158
ON
12345678 159
ON
12345678
Switch Address
161
ON
12345678 162
ON
12345678 163
ON
12345678 164
ON
12345678 165
ON
12345678 166
ON
12345678 167
ON
12345678 168
ON
12345678 169
ON
12345678 170
ON
12345678 171
ON
12345678 172
ON
12345678 173
ON
12345678 174
ON
12345678 175
ON
12345678 176
ON
12345678 177
ON
12345678 178
ON
12345678 179
ON
12345678 180
ON
12345678 181
ON
12345678 182
ON
12345678 183
ON
12345678 184
ON
12345678 185
ON
12345678 186
ON
12345678 187
ON
12345678 188
ON
12345678 189
ON
12345678 190
ON
12345678 191
Switch Address Switch AddressSwitch AddressSwitch Address Switch AddressSwitch Address
ON
12345678
Switch Address
193
ON
12345678 194
ON
12345678 195
ON
12345678 196
ON
12345678 197
ON
12345678 198
ON
12345678 199
ON
12345678 200
ON
12345678 201
ON
12345678 202
ON
12345678 203
ON
12345678 204
ON
12345678
Switch Address
205
ON
12345678 206
ON
12345678 207
ON
12345678 208
ON
12345678 209
ON
12345678 210
ON
12345678 211
ON
12345678 212
ON
12345678 213
ON
12345678 214
ON
12345678 215
ON
12345678 216
ON
12345678 217
ON
12345678 218
ON
12345678 219
ON
12345678 220
ON
12345678 221
ON
12345678 222
ON
12345678 223
ON
12345678
Switch Address
225
ON
12345678 226
ON
12345678 227
ON
12345678 228
ON
12345678 229
ON
12345678 230
ON
12345678 231
ON
12345678 232
ON
12345678 233
ON
12345678 234
ON
12345678 235
ON
12345678 236
ON
12345678 237
ON
12345678 238
ON
12345678 239
ON
12345678 240
ON
12345678 241
ON
12345678 242
ON
12345678 243
ON
12345678 244
ON
12345678 245
ON
12345678 246
ON
12345678 247
ON
12345678 248
ON
12345678 249
ON
12345678 250
ON
12345678 251
ON
12345678 252
ON
12345678 253
ON
12345678 254
ON
12345678 255
Switch Address
ON
12345678 160
ON
12345678 192
ON
12345678 224
ON
12345678 128

EPTZ9200/9300 Series
9
Protocol
The first, second and the third switches on the left are used to set the communication protocol. Please
refer to the sticker on the camera main body for setting up the protocol. The supported protocols are listed
on the sticker. The default protocol is EVF.
DIP Switch
Sticker on the Camera Main Body
Note: If you switch the three protocol switches to ON, the camera will enter a self-test mode.
Baud Rate
The fourth and fifth switches on the left are used to set the baud rate (transmission speed). Please refer to
the sticker on the camera main body for setting up the baud rate. The default baud rate is 9600.
DIP Switch
Sticker on the Camera Main Body
Video Output Format
The sixth and seventh switches on the left are used to set the video output format. Please refer to the
sticker on the camera main body for setting up the video output format. The default video output format is
by OSD (OFF/OFF).
DIP Switch
Sticker on the Camera Main Body

EPTZ9200/9300 Series
10
Installation Requirements
The installation should be handled by a qualified service agent and should be complied with all local
regulations. Service personnel should check potential problem such as surfaces strength, surface
materials, falling objects, outer breaches, building vibration and other similar conditions.
Check for all necessary materials, and ensure that the selected installation location is suitable for the
camera.
Installations on a wall, pole, or ceiling must be able to support at least five times the weight of the full
camera assembly (about 16kg / 35lb).
Installing Outdoor Models
Two mounting types are available for the outdoor models: Wall Mount and Ceiling Mount.
Wall-Mount Installation
1. Drill 4 screw-depth holes for mounting the bracket base plate and then drill a through-wall hole for
inserting the camera cables. You can optionally drill a second through-wall hole to separate cable
feeding (see Step 3).
2. Attach the waterproof silicon pad to the bracket base plate for waterproofing.
Waterproof
silicon pad
Bracket base plate
Bracket base
Bracket
Top housing
Main body

EPTZ9200/9300 Series
11
Wall Mount Bracket
3. Feed the camera’s cables through the conduit in the wall mount bracket.
4. Connect the RS-485, video and power cables through the top hole of the base board. If necessary,
connect the alarm cable as well using the bottom hole.
5. Screw the bracket base to the wall using the 4 screws.
6. Screw the wall mount bracket to the bracket base using the 4 long screws.

EPTZ9200/9300 Series
12
7. Put on the supplied gloves before pushing upward the main body into the top housing. Draw out the
provided rope from the housing and hook it on the rope attachment hook of the main body.
8. Make sure the red triangle on the inside of the top housing lines up with the red triangle on the
outside of the main body. Push the main body upward into the top housing until the orange catches on
both sides click into position.
Top Housing
Main Body
Note:
1. To release the main body, press
the two orange release buttons on both sides. Make sure you are
holding the main body firmly, otherwise it will fall down.
2. To protect the glass dome from getting dirty and scraped up, please put on the supplied gloves
before installing.

EPTZ9200/9300 Series
13
9. Screw the housing cover to the top housing slowly by twisting it clockwise.
Note: When you turn on the power, the camera will enter self-inspection mode and run a self-testing
program. Once this is complete, you will be able to operate it via EKB500 or other control device.
Ceiling Mount Installation
It is required to use the optional In-ceiling Mount Bracket (Recessed Mount Bracket) and Surface Ring to
attach the camera to the ceiling for supporting the camera’s weight. Make sure the ceiling is strong enough
to easily support the weight of the bracket and the camera.
1. Replace the desiccant bags inside the top housing. See Replacing the Desiccant Bags.
2. Cut a hole on the ceiling using the supplied template.

EPTZ9200/9300 Series
14
3. Slightly turn the surface ring and remove it from the in-ceiling mount bracket.
4. Place and then screw the camera’s top housing on the top disk of the in-ceiling mount bracket by using
the 3 short screws.
Top Disk
5. Use a cable or other mechanism to hang the in-ceiling mount bracket on the ceiling.
6. Screw the 3 rotation clips of the in-ceiling mount bracket on the ceiling using a screwdriver.

EPTZ9200/9300 Series
15
7. Put on the supplied gloves before pushing upward the main body into the top housing. Draw out the
provided rope from the housing and hook it on the rope attachment hook of the main body.
8. Make sure the red triangle on the inside of the top housing lines up with the red triangle on the
outside of the main body. Push the main body upward into the top housing until the orange catches on
both sides click into position.
Top Housing
Main Body
Note:
1.
To release the main body, press the two orange release buttons on both sides. Make sure you are
holding the main body firmly, otherwise it will fall down.
2. To protect the glass dome from getting dirty and scraped up, please put on the supplied gloves
before installing.
9. Screw the housing cover to the top housing slowly by twisting it clockwise.

EPTZ9200/9300 Series
16
10. Slide the surface ring to the fillister and slightly turn it until it is firmly fixed.
Note: When you turn on the power, the camera will enter self-inspection mode and run a self-testing
program. Once this is complete, you will be able to operate it via EKB500 or other control device.
5. EKB500 Connection
You can use EKB500 Keyboard to control the EPTZ cameras including the OSD menu setup or PTZ control.
Follow the steps below to connect the EKB500 Keyboard to the EPTZ camera.
1. Connect EPTZ camera to EKB500 either using the RS-485 wire or through the connector box.
•Through the Connector Box
RJ-45 Cable
Connector Box
Blue
Orange
Black
Red
White
Black
Yellow
Green
( RS-485 - )
( RS-485 + )
EPTZ Series 1 EPTZ Series 32
RS-485 +
RS-485 -
EKB500

EPTZ9200/9300 Series
17
•Using the RS-485 wire
EKB500 RS-485 PORTS:
PIN3: RS-485+
PIN6: RS-485-
2. Connect a monitor to the video cable of the EPTZ camera.
3. Connect the power to EKB500 (12 VDC), and the power to EPTZ camera (24 VAC~).
After complete the above connection, you can start operating EPTZ camera with EKB500 Keyboard:
IRIS
+
Focus
F.
Zoom
In
- N. Out
UP
DOWN
LEFT RIGHT
Zoom INZoom OUT
1. Move the Joystick up / down / left / right to shift the camera view in that direction.
2. Twist the top of the Joystick to zoom in / out.
3. Press the Zoom In / Out, Focus F. / N. or IRIS + / -to manually operate these functions.
4. To enter the OSD menu of the EPTZ camera, press both of the Menu and CAM keys at the same time.

EverFocus Electronics Corp.
EverFocus Taiwan:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
mark[email protected]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: [phone]
FAX: [phone]
www.everfocus.de
[email protected]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: [phone]~39
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: [phone]
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[email protected]
EverFocus Japan:
3F, Kuramochi, Building II
2-2-3 Koto-Bashi, Sumida-Ku,
Tokyo, 130-0022, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
[e-mail]
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
P/N: 4605PP4920B032A