mr. steam iDream2 Instruction manual

2019-03-14
iDream/iDream2/iDreamX
Linear
iSteam3 Control PUR100514 07-17
Linear SteamHead PUR100561-1 02-19
SteamLinx Mobile App PUR100518 01-18
AudioSteam3 System PUR100516 01-18
Square Speakers PUR100401SQ 05-13
ChromaSteam3 System PUR100515 01-19
AromaSteam System PUR100402 12.18.2
MS / Super AutoFlush PUR100200E 10-15
MX AutoFlush PUR100532 02-19
Condensation Pan TS0012 12-19

iSteam®3 Control
Installation, Operation & Maintenance Manual
mr
.steam® Feel Good Inc.

When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS
2. Do not permit children under
the age of 16 to use this steambath.
3. Steam is hot and can cause injury
or death if improperly used. Steam rooms contain
steam and elevated temperatures. Please read
and observe all warnings in this manual before
installing or using a steam room.
4. To reduce the risk of injury:
A. The wet surfaces of steam enclosures may be
slippery. Use care when entering or leaving.
B. The steam head is hot. Do not touch the
steamhead and avoid the steam near the
steamhead.
C. Prolonged use of the steam system can raise
excessively the internal human body tempera-
ture and impair the body’s ability to regulate
its internal temperature (hyperthermia). Limit
your use of steam to 10-15 minutes until you
are certain of your body’s reaction.
D. Excessive temperatures have a high
potential for causing fetal damage dur-
ing the early months of pregnancy.
Pregnancy or possibly pregnant women
should consult a physician regarding cor-
rect exposure.
E. Obese persons and persons with a history
of heart disease, low or high blood
pressure, circulatory system problems,
or diabetes should consult a physician
before using a steambath.
F. Persons using medication should consult a
physician before using a steambath since
some medication may induce drowsiness
while other medications may affect heart
rate, blood pressure and circulation.
SAVE THESE INSTRUCTIONS
HYPERTHERMIA occurs when the internal tem-
perature of the body reaches a level several
degrees above the normal body temperature of
98.6° F. The symptoms of hyperthermia include
an increase in the internal temperature of the
body, dizziness, lethargy, drowsiness, and faint-
ing. The effects of hyperthermia include:
a) Failure to perceive heat;
b) Failure to recognize the need to exit the steambath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steambath; and
f) Unconsciousness.
The use of alcohol, drugs,
or medication can greatly
increase the risk of
hyperthermia.
READ ME FIRST!
As you follow these instruc-
tions, you will notice warning and caution
symbols. This blocked information is impor-
tant for the safe and efficient installation and
operation of this generator. These are types
of potential hazards that may occur during
installation and operation:
Indicates a potentially
hazardous situation, which, if not avoided,
could result in death or serious injury.
Indicates a potentially
hazardous situation, which, if not avoided
may result in minor or moderate injury or
product damage.
IMPORTANT NOTE: This highlights
information that is especially relevant to a
problem-free installation.
All information in these instructions is based
on the latest product information available at
the time of publication. Sussman-Automatic
Corporation reserves the right to make
changes at any time without notice.
WARNING
!
WARNING
!
WARNING
!
WARNING
!
WARNING
!
CAUTION
!
WARNING
!
2
39⁄16”
51⁄4”
iSteam3 Template
for the finished wall cut-out

3
Table of Contents:
Important Safety Instructions........................ 2
INSTALLER INFORMATION
Installation Template ................................... 2
Box Content ................................................. 3
Dimensional Information .............................. 3
Before Installing............................................ 4
Locating the Control..................................... 5
Installation with Rough-In Box................... 5-6
Installation without Rough-In Box ................ 6
iSteam®3 Installation ................................. 7-8
USER/HOMEOWNER INFORMATION
Operating Instructions
Stand-By, Start, Dashboard, Set Timer................9
Set Temperature, User Settings .................... 10
ChromaSteam® .......................................... 10
AudioSteam, AromaSteam ............................11
Optional Accessories ....................................11
Settngs: System Setting, Date and Time ...... 12
AutoStart, Passcode, About .......... 13
System Log ................................. 13
Care Tips, Safety & Operating Info ............ 14
Warranty ..................................................... 14
Box Contents:
• iSteam®3 Control
• Control Cable (30 ft.)
• Steamhead
• Tube of Silicone
Sealant
• Owner’s Manual
• Rough-In Box
10:06 AM
ACCESSORIESSETTINGS
START
F
12:16
PM
START
97
61⁄8”
41⁄2”
13 ⁄ 8”
Wall location
for flush mount
Wall location for
optional surface mount
Pigtail
(81⁄2”)
Dimensional Information

mr
.steam®INSTALLER INFORMATION
__________________________________________________________________
4
Do not route iSteam3 control wiring in-
side conduit together with power lines or close to hot
water or steam piping. Doing so may result in an inop-
erative or hazardous installation. Do not alter or modify
any Mr. Steam products including the steam generator
or iSteam3 control. Doing so may result in an inopera-
tive or hazardous installation and will void the warranty.
IMPORTANT NOTES:
• The iSteam3 Control is designed to be ush mounted.
However, the control may be surface mounted when
conditions permit. Consult a MrSteam Customer Ser-
vice or Technical Service representative to determine if
the iSteam3 control can be surface mounted.
• Turn power to the steam generator OFF before
connecting the control to the generator. Failure to turn
the power off will result in an inoperable control.
• Do not operate the iSteam3 control with other than
a MrSteam iSteam3 compatible steam generator.
MrSteam residential steam generators with serial
numbers lower than 1174000, or any other brand of
steam generator are not to be operated with iSteam3
controls. Doing so may result in an inoperative instal-
lation. If your generator’s serial number is lower than
1174000 contact MrSteam Technical Service for up-
grade options and components to enable your steam
generator to function with iSteam3.
• This document contains important safety, operation
and maintenance information. Leave this document
with the homeowner. Do not discard this document.
• Discontinue use of the steam generator or control
if the steam generator is damaged or otherwise not
functioning properly. Doing so may result in an inop-
erative or hazardous installation
• Refer to the Steambath Generator Installation,
Operation and Maintenance Manual for locating and
installing the steamhead.
Do Not alter or modify any MrSteam
products. Doing so may result in an inoperable or
hazardous installation and will void the warranty.
Before Installing
T o avoid unintentional steambath op-
eration, do not locate the control where other controls,
accessories, shower heads, valves, body sprays or simi-
lar within the shower could cause confusion or interfere
with the MrSteam control’s intended use and function.
• To prevent possible injury Do Not use the iSteam®3
control without reading and understanding the
MrSteam steam generator Installation and Operation
Manual.
• A peel and stick warning sticker is provided in the
MrSteam steam generator Installation, Operation and
Maintenance Manual. This manual is provided with
every steam generator. The warning sticker must be
read and permanently affixed in a conspicuous loca-
tion near the steam room. Failure to read and affix
this warning sticker in a conspicuous location may
result in serious injury or death. Please call MrSteam
at 800 767-8326 for a free replacement or if you have
any questions regarding the warning sticker.
• If an iSteam3 control is installed outside the steam
room a Remote Temperature Probe (PN MSTS) must
be installed inside the steam room per installation
instructions supplied with the Remote Temperature
Probe. Failure to install according to instructions will
result in an inoperative control and overheating of
the steam room.
WARNING
!
WARNING
!
CAUTION
!
CAUTION
!
Not actual size

mr
.steam®INSTALLER INFORMATION
__________________________________________________________________
5
3a
3b
4a
4a
5b
5a
Locating the Control
Determine the desired installation location of the control. The iSteam
®
3
controls are designed to be installed inside or outside the steam room
as a matter of personal preference. If the control is installed inside
the steam room:
• Locate the control 4-5 feet above the oor near the bather seating area.
• The control features an integral temperature sensor. Locate the control in a
location representative of the desired steam bathing temperatures. Do not
locate the control above or near the steam head or direct steam emissions.
• Locate the control on a vertical wall.
• The control cable is 30 feet. Insure that the control and steam generator are
located accordingly.
IMPORTANT NOTES:
• If required, contact MrSteam to purchase an optional 60’ iSteam3
control cable part number 104117-60.
• If the control is installed outside the steam room a Remote Temperature
Probe Part Number MSTS must be installed inside the steam room.
Refer to the MSTS installation manual before installing the control.
• Insure MrSteam steam generator is iSteam3 compatible and has
a serial number 1174000 or higher.
Installation with Optional Rough-In Box
A rough-in box is supplied with iSteam3 for new construction. The rough
-in box will allow precise location of the iSteam3 control and provide a
secure and easily identifiable place for the cable while the steam room is
being constructed.
STEP 1 Take the rough-in box out of the package. Remove the two
screws (1a ) and place them in the top and bottom wings of the rough-in
box (1b).
STEP 2 Select a KNOCK-OUT (2a) to route the control cable into the box.
STEP 3 Line up the two TABS (3a) on the right side of the box against a
stud. These TABS help locate the box to sit PROUD of the stud (3b).
STEP 4 SCREW (4a) the two supplied screws into the stud.
STEP 5 Route the CONTROL CABLE (5a) through the back of the rough-in
box and clip it under one of the TABS (5b) that previously held the screws.
The two ends of the control cable are the same.
IMPORTANT NOTE: The control cable should be run in a dedicated 1”
conduit to facilitate installation and service.
1a
1b
1b
2a

mr.steam®INSTALLER INFORMATION
__________________________________________________________________
6
6b
6a
7
Installation with Optional Rough-In Box (cont.)
IMPORTANT NOTE: Be careful not to strain, staple, pinch or
otherwise damage the cables. Route cables as required to permit
replacement. Do not route cables inside conduit together with power
lines or close to hot water or steam piping.
STEP 6
Use the rough-in box as a guide to cut out the
(39⁄16” x 51⁄4”) opening in the wall.
Finish the iSteam®3 installation using the instructions on page 7.
Installation without Rough-In Box
STEP 1
Make a 39⁄16” x 51⁄4” cut-out in the desired location using the
template provided on page 2 of this manual.
STEP 2
Route the control cable from the wall cutout to the steam
generator. Connect one end of the cable to the steam generator
connector. The two ends of the control cable are the same.
IMPORTANT NOTE: Be careful not to strain, staple, pinch or
otherwise damage the control cable. Route cable as required to
permit replacement. Do not route cable inside conduit together
with power lines or close to hot water or steam piping.
Finish the iSteam3 installation using the instructions on page 7.
Rough-In box used as
a guide to cut out the
opening.
39⁄16”
51⁄4”

Control
Pigtail
Control
Cable
Steam
Generator
1a
F
12:16
P M
START
9 7
F
1
2:1
6
P
M
M
M
STAR
T
9
7
R
T
STEP 1
PLUG the 30’ control cable into the iSteam3 control pigtail (1a).
Turn the generator on and test the control to verify correct
connection. With proper function, proceed to Step 2.
mr.steam®INSTALLER INFORMATION
__________________________________________________________________
7
Installation Instructions for iSteam®3
For illustrative purposes only.
CAUTION
!
Do not force or twist cable ends together.
Forcing or twisting cable ends may damage the connectors.

mr.steam®INSTALLER INFORMATION
__________________________________________________________________
8
STEP 2
Peel the double stick adhesive off the back of the
iSteam3 control (2a). Apply a bead of silicone around
the rear of the iSteam3 control to create a moisture
seal (2b). Carefully feed the cables into the rough-in
box and secure the control to the wall. Care must be
taken to not pinch the cables. Ensure the control is
level.
IMPORTANT NOTE:
The control must be installed
with the arrow on the Peel-Off screen protector facing
up. If the Peel-Off screen protector has been removed
see the drawing in Step 2b for the proper orientation.
The control display can be flipped 180 degrees in the
settings menu if installed upside down.
NOTE: The silicone supplied by MrSteam can be
used to meet a variety of sealing and gasketing. It
cures to silicone rubber and adheres to glass, wood,
metal, porcelain, ceramic tile, painted surfaces, many
plastics and rubber. Surfaces must be clean and dry.
Apply thin layer of product. Fit together and support
if necessary. Allow excess material to cure, then trim
with a sharp blade. Sealant “skins” in 5 minutes, dries
to touch in 1 hour. Fully cures and bonds in 24 hrs.
IMPORTANT NOTE: Do not apply excessive amounts
of silicone. Do not apply silicone to any other parts
of the control including the adhesive gasket. Insure
the mounting surface is clean and dry as required for
good adhesion. Hold the control with the arrow on
the screen protector facing up and press the control
against the wall until the adhesive sticks and holds
firmly. Control may have to be supported or secured
until the silicone has cured for 24 hours.
F
12:16
P M
START
9 7
F
1
2:1
6
P
M
M
STAR
T
9
7
Installation Instructions for iSteam®3(cont.)
2b
2c
2a
This
End
Up
Before use, remove
and discard the peel-
off screen protector.
This
End
Up

9
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
IMPORTANT SAFETY INSTRUCTIONS
1. READ AND FOLLOW ALL INSTRUCTIONS
2. Do not permit children under
the age of 16 to use this steambath.
3. Steam is hot and can cause injury
or death if improperly used. Steam rooms contain
steam and elevated temperatures. Please read
and observe all warnings in this manual before
installing or using a steam room.
4. To reduce the risk of injury:
A. The wet surfaces of steam enclosures may be
slippery. Use care when entering or leaving.
B. The steam head is hot. Do not touch the
steamhead and avoid the steam near the
steamhead.
C. Prolonged use of the steam system can raise
excessively the internal human body tempera-
ture and impair the body’s ability to regulate
its internal temperature (hyperthermia). Limit
your use of steam to 10-15 minutes until you
are certain of your body’s reaction.
D. Excessive temperatures have a high
potential for causing fetal damage dur-
ing the early months of pregnancy.
Pregnancy or possibly pregnant women
should consult a physician regarding cor-
rect exposure.
E. Obese persons and persons with a history
of heart disease, low or high blood
pressure, circulatory system problems,
or diabetes should consult a physician
before using a steambath.
F. Persons using medication should consult a
physician before using a steambath since
some medication may induce drowsiness
while other medications may affect heart
rate, blood pressure and circulation.
SAVE THESE INSTRUCTIONS
HYPERTHERMIA occurs when the internal
temperature of the body reaches a level
several degrees above the normal body
temperature of 98.6° F. The symptoms of
hyperthermia include an increase in the
internal temperature of the body, dizzi-
ness, lethargy, drowsiness, and fainting.
The effects of hyperthermia include:
a) Failure to perceive heat;
b) Failure to recognize the need to exit
the steambath;
c) Unawareness of impending risk;
d) Fetal damage in pregnant women;
e) Physical inability to exit the steambath;
and
f) Unconsciousness.
The use of alcohol, drugs,
or medication can greatly increase the
risk of hyperthermia.
The peel and stick
warning label located in the
steam bath generator manual
is an essential part of providing
a safe environment for steam
room users. The peel and stick
warning label must be applied to
the wall of the shower or steam
enclosure, at a point that is vis-
ible to all users. Failure to install
this sticker may result in serious
injury or death.
The location where this owner’s
manual is kept shall be written in
the space provided on the label
using permanent ink.
For a replacement warning label
contact MrSteam customer service
at 1-800-76-STEAM or [email protected]
READ ME FIRST!
As you follow these instruc-
tions, you will notice warning and caution
symbols. This blocked information is impor-
tant for the safe and efficient installation and
operation of this generator. These are types
of potential hazards that may occur during
installation and operation:
Indicates a potentially
hazardous situation, which, if not avoided,
could result in death or serious injury.
Indicates a potentially
hazardous situation, which, if not avoided
may result in minor or moderate injury or
product damage.
IMPORTANT NOTE: This highlights
information that is especially relevant to a
problem-free installation.
All information in these instructions is based
on the latest product information available at
the time of publication. Sussman-Automatic
Corporation reserves the right to make
changes at any time without notice.
WARNING
!
WARNING
!
WARNING
!
WARNING
!
WARNING
!
WARNING
!
CAUTION
!
WARNING
!
mr.steam®
HOMEOWNER SECTION
Not actual size.

mr.steam®USER/HOMEOWNER INFORMATION
__________________________________________________________________
10
F12:16PM
START
97
101F12:16PM
MONDAY
April 28th, 2016
Operating Instructions
Set the steam bathing duration and
temperature according to personal preference,
however it is highly recommended to begin steam
bathing at a low temperature setting to gauge
comfort and safety levels. Set the duration at 10
minutes max. to gauge comfort and safety levels.
This will allow the steam generator to heat up and
begin producing steam.
Stand-By Screen
Touch anywhere on the clock screen to enter
the Start Screen.
Start Screen
Press the START button to turn the steam gen-
erator ON and to display the Dashboard screen.
Steam will begin to flow a few minutes after the
START button is pressed. The time required for
the steam room to reach steam bathing
temperatures depends on the steam room
construction and steam generator specifications.
Dashboard Screen
The Dashboard displays key steam bathing
features and optional accessories in one
convenient screen. The key features include
TIME, TEMPERATURE and USER settings. The
optional accessories include the ChromaSteam®,
AromaSteam and AudioSteam.
Set Timer Screen
Press the TIMER button on the Dashboard to
access the SET TIMER screen. Swipe your finger
up/down to select the desired time (1-60 minutes).
The control will turn off when the steambath
session times out. Then the START screen will
be displayed.
WARNING
!
40min101
o
F
101F12:16PM
STOP
AromaSteam
Adjust Timer
Adjust Set Point
Temperature
Save/Recall
User Settings
Touch to Start
AudioSteam
Main Start Screen
System Settings
ChromaSteam
Touch anywhere to
wake up control
Touch anywhere to operate
steam generator
101F12:16PM
4
0
3
5
30 MIN
2
5
2
0
Swipe
Up and
Down

mr.steam®USER/HOMEOWNER INFORMATION
__________________________________________________________________
11
Set Temperature Screen
Press the TEMPERATURE button on the Dashboard
to access the SET TEMPERATURE screen.
The control is preset and will display a temperature
setting of 110°F (default setting). Swipe your finger
up and down to adjust the desired temperature
(80 - 120 F) in one degree increments.
User Settings
Press the SAVE/RECALL user settings button.
To save the settings press the SAVE CURRENT
SETTINGS button. A keyboard will pop up where
the user name can be entered.
To recall the user settings press the user’s name.
To remove the settings press the delete icon.
A maximum of 8 user settings can be saved.
ChromaSteam
®
The ChromaSteam is an optional accessory that
activates colored lights in the steam room. Press
the CHROMA button to turn it ON. When
ChromaSteam is on, press the CHROMA button
to turn it off.
Press the ChromaSteam Dashboard button to
bring up the color wheel. Touch anywhere on the
wheel to select that color. To adjust the brightness,
use the slider on the bottom of the ChromaSteam
Dashboard. The slider will change color to show
current color selection. (
Note: Brightness cannot be
adjusted in automatic color changing modes
)
Press the Discrete Color Selection button to pick a
preselected list of colors, have white light, or slow
or fast changing color modes.
Press to recall user settings Press to delete user
101F12:16PM
Erica
John
James
Save Current Settings
101F12:16PM
9
7
98
99oF
100
1
0
1
Swipe
Up and
Down
97 F12:16PM
CHROMA
Press to turn ChromaSteam On/Off
Slide to adjust brightness
F12:16PM
97
CHROMA
CH
H
H
H
H
H
H
R
R
R
R
R
R
R
R
R
R
RO
RO
RO
O
O
O
O
O
O
O
O
O
O
R
RO
O
O
O
O
O
O
O
R
R
O
O
M
M
M
M
M
M
M
A
A
A
A
A
Touch wheel to select color
ChromaSteam
On/Off Screen
ChromaSteam
Dashboard
Discrete Color
Selection
F12:16PM
97
Blue
Purple
Red
White
Green
G
G
G
G
G
G
G
G
G
re
re
re
re
re
re
re
e
e
e
e
e
e
e
n
n
n
n
n
n
n
Press to select
discrete colors
Swipe
Up and
Down
Press to save the current settings. A keyboard will open for the
user to enter their name. A maximum of 8 users can be saved .

AromaSteam
The AromaSteam is optional accessory that
automatically infuses aromatic oils into the steam
flow. Press the AromaSteam icon to bring up the
AromaSteam Dashboard. Press the AROMA
button to turn it ON.
The AromaSteam turns OFF automatically when
the steam generator stops.
Press the AROMA button to turn it OFF during
a steam session.
After the steam session has ended the AudioSteam
and ChromaSteam®will remain ON. They can be
turned OFF individually by navigating to each’s
power button, or both can be turned OFF by press-
ing the OFF icon that appears on the START screen.
AudioSteam
Press the music icon to access the AudioSteam
screen.
Press the MUSIC button to turn on AudioSteam.
When AudioSteam is ON, pressing the MUSIC button
will turn it OFF.
Press the AudioSteam Dashboard button to control
the music. When paired to a Bluetooth®device,
iSteam
®
3 will display the song title, artist and album
name. If listening to the FM radio, the station
number will be shown. This space is blank if playing
music from a hard wired source.
Mute
Previous Track or scan backwards
when in FM mode
Play/Pause (Bluetooth only)
Next Track or scan backwards
when in FM mode
If you are using a Bluetooth audio source, it must
be connected for functions to work.
Please refer to the Bluetooth pairing instructions
in the AudioSteam IOM.
Press the Source button to select hardwired AUX
source, Bluetooth source or the FM radio. To unpair
the current connected Bluetooth device, press the
DISCONNECT button.
mr.steam®USER/HOMEOWNER INFORMATION
__________________________________________________________________
12
97
FPM
MUSIC
F
12:16
Press to turn
AudioSteam
ON/OFF
97 F12:16PM
SONG TITLE
Artist
Album Name
AudioSteam
On/Off Screen
Music Dashboard
Source Button
Slide to
adjust
volume
Mute Previous Track Play/Pause Net Track
or scan backwards (Bluetooth only) or scan backwards
when in FM mode when in FM mode
97 F12:16PM
Radio
Bluetooth
AUX
Disconnect
Press to select source
Press to disconnect
current paired
Bluetooth device
101F12:16PM
AROMA
Press to turn
AromaSteam
ON/OFF
F12:16PM
START
97
After steam session is completed
press to turn all accessories off

mr.steam®USER/HOMEOWNER INFORMATION
__________________________________________________________________
13
Settings Screen
The Setting Screen allows access to less frequently
used screens.
System Setting
Scroll through the System Settings list and select which
to adjust.
Temperature Units. Adjust between ˚F and ˚C
Flip Screen. Rotates the screen 180˚ in case the
control was installed upside down
User Interface Color: Toggle between a white and
black background
Brightness: Adjust the screen brightness
Language: Change the language used in the
user interface
Once the setting is changed, press the System Setting
button in the menu on the right to exit
Date and Time
Scroll up and down to select the date and time.
Once selected, press the Set Date and Time button
in the menu on the right to exit
Passcode
AutoStart
Date & Time
System Settings
About
Ab
Ab
Ab
Ab
Ab
Ab
o
o
o
o
u
u
u
u
t
t
t
t
t
F12:16PM
97
F12:16PM
97
Brightness
User Interface Color
Flip Screen
Temperature Units
Language
L
L
L
L
L
L
L
L
L
L
a
a
a
a
a
a
a
ng
ng
ng
ng
ng
ng
ng
g
g
u
u
u
u
u
u
u
a
a
a
a
a
a
a
g
g
g
g
g
g
g
g
g
e
e
e
e
e
e
e
F12:16PM
97
1
6
15
1
4
1
3
Apri
l
March
F
e
b
u
a
r
y
J
anu
ar
y
2016
2
0
1
5
2
0
1
7
2
0
1
4
F12:16PM
97
1
6
15
1
4
1
3
Apri
l
March
F
e
b
u
a
r
y
J
anu
ar
y
2016
2
0
1
5
2
0
1
7
2
0
1
4
System
Setting
Set Date
and Time

mr
.steam®INSTALLER INFORMATION
__________________________________________________________________
14
To prevent injury and/or equipment
damage all troubleshooting is to be performed by
qualified licensed electrician or plumber. Contact
MrSteam technical support at 1-800-727-8326
(East coast) or 1-800-727-8326 (West coast) in the
event that iSteam®3 displays an error code.
mr
.steam®USER/HOMEOWNER INFORMATION
__________________________________________________________________
14
AutoStart
AutoStart will automatically turn the steam genera-
tor on at your preset time. Activating the steam in an occupied
room may subject persons to the hazards described in this
manual. Only activate the steambath if the steam room door is
closed. Activating or using the steambath with an open door
may cause property damage or injury to persons outside of the
steam bath.
The AutoStart feature can be used to turn on the steambath at
a predetermined time. Select the day(s) of the week and the
time of day you would like to turn the steam bath on.
When AutoStart starts your steambath it will allow the steam-
bath to run for only 10 minutes. To continue steam bathing
press the continue button. If the continue button is pressed,
AutoStart will remain active for the next scheduled start time.
To stop the steam bath press the STOP button.
If the STOP button or 10 minute time out turns the steam
generator off, AutoStart will automatically be deactivated.
To create an AutoStart time, press the + icon. Select the start time to
adjust the day and time for AutoStart. A maximum of 8 start times can
be programmed. To delete a start time, press the trash can icon.
To turn AutoStart ON, press the AutoStart button above the start time list.
Enter a 4 digits
code to lock the
keypad. The same
code will be used
to unlock it.
4321
WARNING
!
WARNING
!
AUTOSTART
Day Time
Every day 12:00am
FPM
77 12:16
Turn AutoStart
ON or OFF
Create a new AutoStart Delete start time
time (max. of 8)
Passcode
The Passcode feature can help prevent unintentional use of
the steambath. Please refer to the steam generator Installation,
Operation and Maintenance manual before using the steam-
bath. The Passcode feature cannot insure unintentional use of
the steambath.
To turn the Passcode lock ON or OFF, press the lock icon.
Enter a 4 digit passcode using the keypad. Press the entire but-
ton to SAVE the passcode. The next time the iSteam3 control is
turned on the user will be prompted to enter the passcode.
Press the Back button to exit without storing the passcode lock.
If you forget your passcode, power should be turned off at the
circuit breaker. After 1 minute turn the breaker back on. The
passcode lock will automatically be turned OFF.
About Screen
Press ABOUT to view the accessories connected to the
steam generator.
System Log
Press SYSTEM LOG to view an error log created by the
steam generator.

mr
.steam®USER/HOMEOWNER INFORMATION
__________________________________________________________________
15
Care Tips
Use only mild soap and water on a soft cloth to clean
the control. Do not use abrasive cleansers.
Safety and Operating Information
A peel and stick warning sticker is provided
in the MrSteam steam generator Installation, Operation
and Maintenance Manual. This manual is provided with
every steam generator. The warning sticker must be read
and permanently affixed in a conspicuous location near the
steam room. Failure to read and affix this warning sticker in
a conspicuous location may result in serious injury or death.
Please call MrSteam at 800 767-8326 for a free replacement
or if you have any questions regarding the warning sticker.
Set the steam bathing duration and tempera-
ture according to personal preference, however it is highly
recommended to begin steam bathing at a low temperature
setting to gauge comfort and safety levels. Set the duration
at 10 minutes max. to gauge comfort and safety levels. This
will allow the steam generator to heat up and begin produc-
ing steam.
Do not use any iSteam®3 control without
reading and understanding the MrSteam steam generator
Installation and Operation Manual (PN 100472). Failure to
read and understand these instructions may result in an in-
operative or hazardous installation.
If an iSteam3 control is installed outside the
steam room a Remote Temperature Probe (PN MSTS) must
be installed inside the steam room per installation instruc-
tions supplied with the Remote Temperature Probe. Failure
to install according to instructions will result in an inopera-
tive control and overheating of the steam room.
CAUTION
!
CAUTION
!
WARNING
!
WARNING
!
Warranty
To view or download the MrSteam Control Warranty
and register your product go to
: blog.mrsteam.com/wr

mr.steam®
Feel Good Inc.
®
www.mrsteam.com
mr.steam® Sussman-Automatic Corporation®I [email protected] I www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 I 9410 S. La Cienega Blvd. Inglewood CA 90301
1 800 767 8326 fax:[phone] I 1 800 72 STEAM fax:[phone]
2017 © Sussman-Automatic Corporation I MrSteam and des., A Lifetime of Pleasure, AirTempo, AromaFlo, AudioWizard, AutoFlush, Butler Package, ChromaSteam,
Clean Steam...Every Time, Club Therapy, Digital 1, Express Steam, Feel Good Inc., From Bathroom to Spa, iButler, iGenie, iSizing, iSteam, Making Wellness a Way of Life,
Music Therapy, Spa Package, Steam on Demand, Steam@Home, iTempo, iTempo/Plus, SmartSizing, SteamStart, SteamStop, SteamTherapy, Sussman, Tala, Bath & Body
Therapy, The Intelligent Steambath, Valet Package, Virtual Spa System, Voice Genie and Voice Wizard are registered trademarks of Sussman-Automatic Corporation.
pur 100514 rev 7.17
Products, information and specifications are subject to change without notice. For more information call
Sales & Support at 1.800.76.STEAM (East Coast) or 1.800.72.STEAM (West Coast) for more information.

READ ME FIRST!
As you ollow these instructions, you will notice
warning and caution symbols. This in ormation
is important or the proper, sa e and trouble ree
installation o the Linear Steam Head. These are
types o potential hazards that may occur i in-
stallation instructions are not care ully ollowed.
This signals a situation where injury or property
damage may occur i you do not ollow instructions.
IMPORTANT NOTE: This highlights in ormation that is espe-
cially relevant to a problem- ree installation.
All in ormation in these instructions is based on the latest in orma-
tion available at the time o publication. Sussman-Automatic Corpo-
ration reserves the right to make changes at any time without notice.
1
Linear Steam Head® mr.steam
®
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Installation Instructions Model 104216
• Linear Steam Head model 104216 is suitable or MrSteam
generator models MS90 – MS400, MSSUPER1–
MSSUPER3, MX4 – MX6 and CT6 – CT15.
Do not use Linear Steam Head model 104216 or any
other MrSteam steam generator. Do not use the Linear
Steam Head with any steam generator that is not a
MrSteam steam generator. Failure to ollow these
instructions may result in a leak within the wall cavity and
cause problems associated with leaks, moisture and
property damage rom leaks.
• Do not use the Linear Steam Head with any steam
generator that is not a MrSteam steam generator. Failure
to ollow these instructions result in steam head operation
where incidental contact by the bather with direct steam
emission cannot occur. Do not locate the steam head in
any location where the steam emission zone is near a seat,
bench or any space occupied by any persons. Failure to
ollow these instructions may result in a hazardous
condition, scalding or personal injury.
Using model 104216 or any steam generator model larger
than the MS Super 3, or or any non MrSteam brand
generators may result in an improper installation or
hazardous condition.
• MrSteam steam generators Models MX4, MX5 and MX6
require two 104216 steam heads. Failure to use two steam
heads may result in steam head operation where incidental
contact by the bather with direct steam emission may
occur. Do not locate the steam head in any location where
the steam emission zone is near a seat, bench or any
space occupied by any persons. Failure to ollow these
instructions may result in a hazardous condition, scalding
or personal injury.
• Because the steam head and direct steam emission are
very hot, locate the steam head where incidental contact
by the user with the steam head or direct steam emission
cannot occur.
• Model 104216 Linear Steam Heads are or residential and
Day Spa use only. Do not use Model 104216 Linear Steam
CAUTIONS
!
Heads or commercial installations or with commercial
(CU) steam generators. Using Model 104216 Linear
Steam Heads or commercial installations or with
commercial (CU) steam generators may result in steam
head operation where incidental contact by the bather
with direct steam emission may occur. Failure to ollow
these instructions may result in a hazardous condition,
scalding or personal injury.
• Install in a horizontal orientation only. Installation in a
non-horizontal orientation may concentrate the steam
and result in excessive temperatures. Failure to install in
a horizontal orientation may result in steam head
operation where incidental contact by the bather with
direct steam emission may occur. Failure to ollow these
instructions may result in a hazardous condition, scalding
or personal injury.
• Insulate the steam head and piping as required to reduce
temperatures within the wall cavity. Do not locate the
steam head or plumbing near any materials, including
wiring, devices, or products that may be adversely
a ected by elevated temperatures. Failure to ollow
these instructions may result in the ailure o materials,
including wiring, devices, or products.
• Steam bath controls eature an integral temperature
sensor. Locate the steam head in a location where steam
emissions will not directly come in contact with the steam
control. Failure to ollow these instructions may result in a
hazardous condition, scalding or personal injury.
• Use the supplied high temperature silicone sealant or
equal silicone based product. Do not seal the steam
head with grout or any other material that may be
compromised adversely by heat.
• The Linear Steam Head model 104216 must be installed
by a quali ied and licensed plumber. Failure to use a
quali ied and licensed plumber may result in a leak within
the wall cavity and cause problems associated with leaks,
moisture and property damage rom leaks.
(continued on next page)
CAUTION
!
100561-1 Rev 2.19
mr
.steam
®
Sussman-Automatic Corp® [email protected] www.mrsteam.com
43-20 34th Street, Long Island City, NY 11101 tel: 1 800 76 STEAM
9410 S. La Cienega Blvd. Inglewood CA 90301 tel: 1 800 72 STEAM

READ ME FIRST! (cont.)
Linear Steam Head®
–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Installation Instructions: Model 104216
mr.steam
®
2
NOTE: Drawings are for illustrative purposes only. Consult with quali ied designer, architect or contractor or steam room construction.
21/4”
Round
Mounting
Holes
5/8”
71/2”
Slotted
Mounting
Holes
2”
Steam
Outlet
141/8”
3/4”NPT Steam
Outlet Connection
121/8”
Figure 1
• DO NOT use black iron pipe or galvanized pipe or the
steam line. Use brass pipe or copper tubing only, and
in accordance with national and local plumbing codes.
• Do not modi y or alter the steam head. Do not cover,
block or insert any product that is not a MrSteam
supplied product into the steam outlet. Failure to
ollow these instructions may result in a leak within the
wall cavity, or result in a hazardous condition and/or
personal injury.
IMPORTANT NOTES:
• See the Installation and Operation Manual provided
with the steam generator or additional important
installation and operation in ormation. I this
installation and operation manual is not available then
go to www.mrsteam.com or an online copy, or
contact MrSteam Customer or Technical Services at
800-767-8326 or 800-727-8326 or a ree copy.
• Do not disassemble the steam head. The steam head
is shipped ully assembled and requires no additional
assembly. Failure to ollow these instructions may result
in a leak within the wall cavity and cause problems
associated with leaks, moisture and property damage
rom leaks.
• Consult with supplier o acrylic, iberglass and other
non-heat resistant enclosures or elevated temperatures,
steam, and moisture compatibility. Consult with supplier
o acrylic, iberglass and other non-heat resistant
enclosures or recommended steam head locations.
• To prevent damage to property do not locate the steam
head where steam, elevated temperatures, moisture or
water can contact any products, wall sur aces, materials,
door seals, devices, electronics that are not designed
or steam, elevated temperatures, moisture or water.
• Do not use abrasive cleansers or chemicals to clean
the steam head. Use only water with mild soap and a
non-abrasive sponge. The use o abrasive cleansers
or chemicals will damage the inish on the Linear
Steam Head.
BOX CONTENTS:
• Linear Steam Head
• Silicone Sealant
• Installation Instructions
Number Steam
Generator of Linear Emission
Model Steam Heads Zone
MS90 – MS400 1 18”
Super1 – Super3 1 24”
MX4 – MX6 2 24”
CT6, CT9 1 18”
CT12, CT15 1 24”
CAUTION
!

INSTALLATION STEPS
Because steam emissions are very hot,
locate the steam head where incidental contact by
the bather with direct steam emission cannot occur.
Do not locate the steam head in any location where
the steam emission zone is near a seat, bench or any
space occupied by any persons. See Fig. 2 or a
diagram o the steam emission zone. Failure to ollow
these instructions may result in a hazardous condition,
scalding or personal injury.
Do not install a Linear Steam Head in a
tub or acrylic/ iberglass shower enclosure. Failure to
ollow these instructions may result in a hazardous
condition, scalding or personal injury
STEP 1. Locate the steam head 6-12” above the
inished loor. Do not locate the steam head in any
location where the steam emission zone is near a seat,
bench, or any space occupied by any persons. See
Fig. 2 or a diagram o the steam emission zone.
STEP 2. Con irm proper stud spacing: The studs must
have a minimum spacing o 14-1/8” and a maximum
spacing 14-1/2 “. I the stud spacing is outside the
required range then shim or otherwise reposition the
studs as required.
Installing the steam head between
incorrectly spaced studs may result in damage to the
steam head and result in a leak within the wall cavity
and cause property damage.
STEP 3. Determine the location o the inished wall
sur ace. Mount the steam head between two studs
using the our slotted holes to position the steam
outlet ace to be lush or extend 1/8” rom the
inished wall sur ace (see Fig. 4).
Failure to position the steam head ace
to be lush or extended 1/8” rom the inished wall
sur ace may result in a leak within the wall cavity and
cause problems associated with leaks, moisture and
property damage rom leaks.
STEP 4. Use a level to ensure the steam head is level
(see Fig. 3 ) and the steam head ace is lush or
extends 1/8” rom the inished wall sur ace. Install the
our screws in the mounting holes to secure the steam
head to the studs.
Linear Steam Head®
–––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Installation Instructions: Model 104216
mr.steam
®
3
NOTE: Drawings are for illustrative purposes only. Consult with quali ied designer, architect or contractor or steam room construction.
Copper Tubing
or Brass Pipe
(not provided)
Steam Outlet
Threaded
Adaptor or
Thread Plug
as required
(not provided)
Stud
Stud
Level
141/8”–141/2”
Figure 3
CAUTION
!
CAUTION
!
Steam
head
6”-12”
above
floor
STEAM
EMISSION
ZONE
Ste am Room
Int erior
STEAM
EMISSION
Figure 2
CAUTION
!
CAUTION
!