MSC A100 User manual
1. Important Updates and Safeguards
I. Caution: Over-heating may result under long periods of
use, and can lead to early bulb burn out.
II. Please read the manual carefully before operating
projector. To ensure stable power supply, please use
standard power cable.
III. Please use the power supply and cable indicated on
the rating label. The projector should be kept away from
cloths, sofas and anything that may block the ventilation
scoop. Please keep the unit away from flammable and
explosive materials.
IV. Please do not disassemble the unit yourself as this will
invalidate the warranty service. To protect your eyes,do
not stare directly at the lens when the projector is on. The
projector must be kept away from water and any other
liquids.
V. To prevent electric shock, please keep the projector out
of the rain and away from moisture. It is recommended to
switch off the projector after it has run for6 hours
non-stop. Please use the original foam and other
cushioning materials when transporting the projector.
VI. This model does NOT have a working SD Card Slot.
If you experience any issues, difficulties, or
have any questions, please check our FAQ
at www.msca100.com or contact our
and we will be happy to assist you.
www.msca100.com
2. Accessories List
AV Signal Cable
Remote Control
Power Cable
User Manual
1pc
1pc
1pc
1pc
3.Specification
5. Structural Diagram 7. Function Operation
MP3 / WMA / M4A / OGGAudio Format
Image Format
Video Format
File Format
JPG / JPEG / BMP / PNG
MP4, MKV, WMA, RMVB, RM, AVI, FLV,
TRP, VOB, 3GP, DIVX, TP, TS, MPG, M2TS
TXT
4. Multimedia Supported Files
The projector does not support Dolby audio decoding.
Model:
Lamp:
Image system:
Language:
Input voltage:
Projection mode:
Working temp:
Operation mode:
Output:
Input:
MSC A100
LED
LCD
English, Japanese, Chinese
AC100V-240V
Front or rear
5-35 °C
Manual / Remote Control
Headphone
HDMI / USB / VGA / AV
1. Power
2. Menu
3. Arrow keys
4. Mute
5. Volume Down
6. Play
7. Source
8. Enter
9. Volume Up
10. Exit
11. Homepage
1
2
3
4
5
6
7
8
9
10
11
1 2 3 4 5 6 7
6. PaneI Functions
1. VGA for laptop or computer input
2. IR for remote control
3. Headphone port for audio output
4. AV port for Audio/Video signal input
5. USB port for multimedia play
6. OUT 5V
7. HDMI port for HD signal input
1
5
3
2
4
6
78
9
1. Source: choose the
input signal source
2. Menu: operate
multiple functions
3. Return
4. Signal lights
5. Up: move up
6. Power Button: power on or off
7. Left: move left or volume down
8. Down: move down
9. Right: move right or volume up
MSC A100
INSTRUCTION MANUAL
1. Important Updates and Safeguards
I. Caution: Over-heating may result under long periods of
use, and can lead to early bulb burn out.
II. Please read the manual carefully before operating
projector. To ensure stable power supply, please use
standard power cable.
III. Please use the power supply and cable indicated on
the rating label. The projector should be kept away from
cloths, sofas and anything that may block the ventilation
scoop. Please keep the unit away from flammable and
explosive materials.
IV. Please do not disassemble the unit yourself as this will
invalidate the warranty service. To protect your eyes,do
not stare directly at the lens when the projector is on. The
projector must be kept away from water and any other
liquids.
V. To prevent electric shock, please keep the projector out
of the rain and away from moisture. It is recommended to
switch off the projector after it has run for6 hours
non-stop. Please use the original foam and other
cushioning materials when transporting the projector.
VI. This model does NOT have a working SD Card Slot.
If you experience any issues, difficulties, or
have any questions, please check our FAQ
at www.msca100.com or contact our
and we will be happy to assist you.
www.msca100.com
2. Accessories List
AV Signal Cable
Remote Control
Power Cable
User Manual
1pc
1pc
1pc
1pc
3.Specification
5. Structural Diagram 7. Function Operation
MP3 / WMA / M4A / OGGAudio Format
Image Format
Video Format
File Format
JPG / JPEG / BMP / PNG
MP4, MKV, WMA, RMVB, RM, AVI, FLV,
TRP, VOB, 3GP, DIVX, TP, TS, MPG, M2TS
TXT
4. Multimedia Supported Files
The projector does not support Dolby audio decoding.
Model:
Lamp:
Image system:
Language:
Input voltage:
Projection mode:
Working temp:
Operation mode:
Output:
Input:
MSC A100
LED
LCD
English, Japanese, Chinese
AC100V-240V
Front or rear
5-35 °C
Manual / Remote Control
Headphone
HDMI / USB / VGA / AV
1. Power
2. Menu
3. Arrow keys
4. Mute
5. Volume Down
6. Play
7. Source
8. Enter
9. Volume Up
10. Exit
11. Homepage
1
2
3
4
5
6
7
8
9
10
11
1 2 3 4 5 6 7
6. PaneI Functions
1. VGA for laptop or computer input
2. IR for remote control
3. Headphone port for audio output
4. AV port for Audio/Video signal input
5. USB port for multimedia play
6. OUT 5V
7. HDMI port for HD signal input
1
5
3
2
4
6
78
9
1. Source: choose the
input signal source
2. Menu: operate
multiple functions
3. Return
4. Signal lights
5. Up: move up
6. Power Button: power on or off
7. Left: move left or volume down
8. Down: move down
9. Right: move right or volume up
MSC A100
INSTRUCTION MANUAL
1. Important Updates and Safeguards
I. Caution: Over-heating may result under long periods of
use, and can lead to early bulb burn out.
II. Please read the manual carefully before operating
projector. To ensure stable power supply, please use
standard power cable.
III. Please use the power supply and cable indicated on
the rating label. The projector should be kept away from
cloths, sofas and anything that may block the ventilation
scoop. Please keep the unit away from flammable and
explosive materials.
IV. Please do not disassemble the unit yourself as this will
invalidate the warranty service. To protect your eyes,do
not stare directly at the lens when the projector is on. The
projector must be kept away from water and any other
liquids.
V. To prevent electric shock, please keep the projector out
of the rain and away from moisture. It is recommended to
switch off the projector after it has run for6 hours
non-stop. Please use the original foam and other
cushioning materials when transporting the projector.
VI. This model does NOT have a working SD Card Slot.
If you experience any issues, difficulties, or
have any questions, please check our FAQ
at www.msca100.com or contact our
and we will be happy to assist you.
www.msca100.com
2. Accessories List
AV Signal Cable
Remote Control
Power Cable
User Manual
1pc
1pc
1pc
1pc
3.Specification
5. Structural Diagram 7. Function Operation
MP3 / WMA / M4A / OGGAudio Format
Image Format
Video Format
File Format
JPG / JPEG / BMP / PNG
MP4, MKV, WMA, RMVB, RM, AVI, FLV,
TRP, VOB, 3GP, DIVX, TP, TS, MPG, M2TS
TXT
4. Multimedia Supported Files
The projector does not support Dolby audio decoding.
Model:
Lamp:
Image system:
Language:
Input voltage:
Projection mode:
Working temp:
Operation mode:
Output:
Input:
MSC A100
LED
LCD
English, Japanese, Chinese
AC100V-240V
Front or rear
5-35 °C
Manual / Remote Control
Headphone
HDMI / USB / VGA / AV
1. Power
2. Menu
3. Arrow keys
4. Mute
5. Volume Down
6. Play
7. Source
8. Enter
9. Volume Up
10. Exit
11. Homepage
1
2
3
4
5
6
7
8
9
10
11
1 2 3 4 5 6 7
6. PaneI Functions
1. VGA for laptop or computer input
2. IR for remote control
3. Headphone port for audio output
4. AV port for Audio/Video signal input
5. USB port for multimedia play
6. OUT 5V
7. HDMI port for HD signal input
1
5
3
2
4
6
78
9
1. Source: choose the
input signal source
2. Menu: operate
multiple functions
3. Return
4. Signal lights
5. Up: move up
6. Power Button: power on or off
7. Left: move left or volume down
8. Down: move down
9. Right: move right or volume up
MSC A100
INSTRUCTION MANUAL
1. Important Updates and Safeguards
I. Caution: Over-heating may result under long periods of
use, and can lead to early bulb burn out.
II. Please read the manual carefully before operating
projector. To ensure stable power supply, please use
standard power cable.
III. Please use the power supply and cable indicated on
the rating label. The projector should be kept away from
cloths, sofas and anything that may block the ventilation
scoop. Please keep the unit away from flammable and
explosive materials.
IV. Please do not disassemble the unit yourself as this will
invalidate the warranty service. To protect your eyes,do
not stare directly at the lens when the projector is on. The
projector must be kept away from water and any other
liquids.
V. To prevent electric shock, please keep the projector out
of the rain and away from moisture. It is recommended to
switch off the projector after it has run for6 hours
non-stop. Please use the original foam and other
cushioning materials when transporting the projector.
VI. This model does NOT have a working SD Card Slot.
If you experience any issues, difficulties, or
have any questions, please check our FAQ
at www.msca100.com or contact our
and we will be happy to assist you.
www.msca100.com
2. Accessories List
AV Signal Cable
Remote Control
Power Cable
User Manual
1pc
1pc
1pc
1pc
3.Specification
5. Structural Diagram 7. Function Operation
MP3 / WMA / M4A / OGGAudio Format
Image Format
Video Format
File Format
JPG / JPEG / BMP / PNG
MP4, MKV, WMA, RMVB, RM, AVI, FLV,
TRP, VOB, 3GP, DIVX, TP, TS, MPG, M2TS
TXT
4. Multimedia Supported Files
The projector does not support Dolby audio decoding.
Model:
Lamp:
Image system:
Language:
Input voltage:
Projection mode:
Working temp:
Operation mode:
Output:
Input:
MSC A100
LED
LCD
English, Japanese, Chinese
AC100V-240V
Front or rear
5-35 °C
Manual / Remote Control
Headphone
HDMI / USB / VGA / AV
1. Power
2. Menu
3. Arrow keys
4. Mute
5. Volume Down
6. Play
7. Source
8. Enter
9. Volume Up
10. Exit
11. Homepage
1
2
3
4
5
6
7
8
9
10
11
1 2 3 4 5 6 7
6. PaneI Functions
1. VGA for laptop or computer input
2. IR for remote control
3. Headphone port for audio output
4. AV port for Audio/Video signal input
5. USB port for multimedia play
6. OUT 5V
7. HDMI port for HD signal input
1
5
3
2
4
6
78
9
1. Source: choose the
input signal source
2. Menu: operate
multiple functions
3. Return
4. Signal lights
5. Up: move up
6. Power Button: power on or off
7. Left: move left or volume down
8. Down: move down
9. Right: move right or volume up
MSC A100
INSTRUCTION MANUAL
1. Important Updates and Safeguards
I. Caution: Over-heating may result under long periods of
use, and can lead to early bulb burn out.
II. Please read the manual carefully before operating
projector. To ensure stable power supply, please use
standard power cable.
III. Please use the power supply and cable indicated on
the rating label. The projector should be kept away from
cloths, sofas and anything that may block the ventilation
scoop. Please keep the unit away from flammable and
explosive materials.
IV. Please do not disassemble the unit yourself as this will
invalidate the warranty service. To protect your eyes,do
not stare directly at the lens when the projector is on. The
projector must be kept away from water and any other
liquids.
V. To prevent electric shock, please keep the projector out
of the rain and away from moisture. It is recommended to
switch off the projector after it has run for6 hours
non-stop. Please use the original foam and other
cushioning materials when transporting the projector.
VI. This model does NOT have a working SD Card Slot.
If you experience any issues, difficulties, or
have any questions, please check our FAQ
at www.msca100.com or contact our
and we will be happy to assist you.
www.msca100.com
2. Accessories List
AV Signal Cable
Remote Control
Power Cable
User Manual
1pc
1pc
1pc
1pc
3.Specification
5. Structural Diagram 7. Function Operation
MP3 / WMA / M4A / OGGAudio Format
Image Format
Video Format
File Format
JPG / JPEG / BMP / PNG
MP4, MKV, WMA, RMVB, RM, AVI, FLV,
TRP, VOB, 3GP, DIVX, TP, TS, MPG, M2TS
TXT
4. Multimedia Supported Files
The projector does not support Dolby audio decoding.
Model:
Lamp:
Image system:
Language:
Input voltage:
Projection mode:
Working temp:
Operation mode:
Output:
Input:
MSC A100
LED
LCD
English, Japanese, Chinese
AC100V-240V
Front or rear
5-35 °C
Manual / Remote Control
Headphone
HDMI / USB / VGA / AV
1. Power
2. Menu
3. Arrow keys
4. Mute
5. Volume Down
6. Play
7. Source
8. Enter
9. Volume Up
10. Exit
11. Homepage
1
2
3
4
5
6
7
8
9
10
11
1 2 3 4 5 6 7
6. PaneI Functions
1. VGA for laptop or computer input
2. IR for remote control
3. Headphone port for audio output
4. AV port for Audio/Video signal input
5. USB port for multimedia play
6. OUT 5V
7. HDMI port for HD signal input
1
5
3
2
4
6
78
9
1. Source: choose the
input signal source
2. Menu: operate
multiple functions
3. Return
4. Signal lights
5. Up: move up
6. Power Button: power on or off
7. Left: move left or volume down
8. Down: move down
9. Right: move right or volume up
MSC A100
INSTRUCTION MANUAL
14. iOS Cast
Attention: The projector needs to be connected to the
network first when using Apple Airplay for the first time
or finishing the projector upgrade.
Step1: Select “iOS Cast” on the home screen.
Step2: iOS devices and projectors must be connected
to the same network, or connect the iOS device to the
wireless network issued by the projector.
Step3: Open the control center of iOS device, Choose
“Screen Mirroring”.
Step4: Choose on the name of the projector device.
Setup
iOS Cast
Miracast
8. Power On/Off
Connect the power cord to the projector and connect
the power cord to the outlet before the power is turned
on.
Once the projector is plugged in, it will be in
Standby mode.
Power on: Press the power button on the remote
control once to turn the projector on.
Power off: Press the power button on the remote
control twice to turn the projector off.
9. Focus/Keystone
ll. Keystone Correction
10. Setup
Set Submenu Function
Network:
Scan / Auto IP / Static IP / Disconnect
Projection:
Projection Mode: Front Desktop / Rear Desktop / Front
Ceiling / Rear Ceiling
Advanced:
Language / Boot Source / Sleep Timer / Local Update /
Online Update / Restore Factory Defauit
Step1: Choose “Setup” on the right of the interface,
then find “Network”.
11. WiFi Connection
Step2: Find “WiFi”.
Step3: Choose “Scan”. Select your wireless network
from list and type in the password.
Step4: Press the “Exit” key on the remote control and
then confirm the connection.
15. Miracast
Step1: Select the Miracast on the home screen.
Step2: Open the “wireless display” function of Android
device.
Step3: Select the corresponding projector device name.
Attention: Note that different Android devices have
different ways to open the “wireless display”. For
details, please refer to the instructions for Android
devices.
Media
12. Multimedia Play
Step1: Insert the USB flash drive into the projector's
USB interface.
Step2: Select “Media” and press “OK” to enter.
Step3: Select the file you like to play.
Step2: Make sure that the signal source you selected is
consistent with the access signal source.
1. Select your signal source: "HDMI", "VGA", "AV".
2. Customize your image settings. "Image Mode",
"Aspect Ratio","Brightness", "Contrast", "Color",
"Sharpness".
3. Customize your audio settings. "Sound Mode",
"Bass", "Treble", "Balance","Equalizer".
Source
13. Signal Source Settings
Step1: Press "OK" button to enter "Source".
Source
AV
VGA
HDMI
Image
Color
Sharpness
Contrast
Brightness
Aspect Ratio
Image Mode
Sound
Equalizer
Balance
Treble
Bass
Sound Mode
1
2
1. Focus
2. Keystone
Please adjust the "Keystone Correction" dial ring until
the image is displayed normally.
Note:The projector has only vertical keystone correction
and no horizontal correction.
Make sure your projector is level with the projected
image.
HOME> Setup> Projection
HOME> Setup> Network
HOME> Media> Movie
Movie Music
USB DISK
Photo Text
1/1
Network
WiFi Scan TP-LINK_E5A2
TP-LINK_E5A3
TP-LINK_E5A4
Auto IP
Static IP
Projection Advanced Information
Network Projection Advanced Information
Front Destktop
Projection Mode
disconnect
Miracast
Cast from Android Devices
1.On your Android Mobile/Tab,
open the settings menu.
2.Access your display settings or
screen-mirroring.
3.Select your Miracast
receiver: ZYCast-859c(mcast)
Wireless display
Connect to a display using WLAN
Mirror your iPhone or iPad
Make sure that your iOS device is connected to the same network as your
Prjector, or connect iOS device with AP by Projector: Projector AP
1.On your iOS device, open
Control Center and tap Screen
Mirroring.
2.Looking for devices that can
be mirrored on. 3.Select ZYCast-859c(mcast)
from the list.
Screen
Mirroring
Screen Mirroring
Looking for Apple TV... ZYCast-859c(mcast)
l. Focusing
Place the projector in a certain place within the required
distance so that the lens is perpendicular to the screen
then rotate the lens until the image is clear.
Screen Mirroring Mobile
Projector
Tab
Focus
Keystone
14. iOS Cast
Attention: The projector needs to be connected to the
network first when using Apple Airplay for the first time
or finishing the projector upgrade.
Step1: Select “iOS Cast” on the home screen.
Step2: iOS devices and projectors must be connected
to the same network, or connect the iOS device to the
wireless network issued by the projector.
Step3: Open the control center of iOS device, Choose
“Screen Mirroring”.
Step4: Choose on the name of the projector device.
Setup
iOS Cast
Miracast
8. Power On/Off
Connect the power cord to the projector and connect
the power cord to the outlet before the power is turned
on.
Once the projector is plugged in, it will be in
Standby mode.
Power on: Press the power button on the remote
control once to turn the projector on.
Power off: Press the power button on the remote
control twice to turn the projector off.
9. Focus/Keystone
ll. Keystone Correction
10. Setup
Set Submenu Function
Network:
Scan / Auto IP / Static IP / Disconnect
Projection:
Projection Mode: Front Desktop / Rear Desktop / Front
Ceiling / Rear Ceiling
Advanced:
Language / Boot Source / Sleep Timer / Local Update /
Online Update / Restore Factory Defauit
Step1: Choose “Setup” on the right of the interface,
then find “Network”.
11. WiFi Connection
Step2: Find “WiFi”.
Step3: Choose “Scan”. Select your wireless network
from list and type in the password.
Step4: Press the “Exit” key on the remote control and
then confirm the connection.
15. Miracast
Step1: Select the Miracast on the home screen.
Step2: Open the “wireless display” function of Android
device.
Step3: Select the corresponding projector device name.
Attention: Note that different Android devices have
different ways to open the “wireless display”. For
details, please refer to the instructions for Android
devices.
Media
12. Multimedia Play
Step1: Insert the USB flash drive into the projector's
USB interface.
Step2: Select “Media” and press “OK” to enter.
Step3: Select the file you like to play.
Step2: Make sure that the signal source you selected is
consistent with the access signal source.
1. Select your signal source: "HDMI", "VGA", "AV".
2. Customize your image settings. "Image Mode",
"Aspect Ratio","Brightness", "Contrast", "Color",
"Sharpness".
3. Customize your audio settings. "Sound Mode",
"Bass", "Treble", "Balance","Equalizer".
Source
13. Signal Source Settings
Step1: Press "OK" button to enter "Source".
Source
AV
VGA
HDMI
Image
Color
Sharpness
Contrast
Brightness
Aspect Ratio
Image Mode
Sound
Equalizer
Balance
Treble
Bass
Sound Mode
1
2
1. Focus
2. Keystone
Please adjust the "Keystone Correction" dial ring until
the image is displayed normally.
Note:The projector has only vertical keystone correction
and no horizontal correction.
Make sure your projector is level with the projected
image.
HOME> Setup> Projection
HOME> Setup> Network
HOME> Media> Movie
Movie Music
USB DISK
Photo Text
1/1
Network
WiFi Scan TP-LINK_E5A2
TP-LINK_E5A3
TP-LINK_E5A4
Auto IP
Static IP
Projection Advanced Information
Network Projection Advanced Information
Front Destktop
Projection Mode
disconnect
Miracast
Cast from Android Devices
1.On your Android Mobile/Tab,
open the settings menu.
2.Access your display settings or
screen-mirroring.
3.Select your Miracast
receiver: ZYCast-859c(mcast)
Wireless display
Connect to a display using WLAN
Mirror your iPhone or iPad
Make sure that your iOS device is connected to the same network as your
Prjector, or connect iOS device with AP by Projector: Projector AP
1.On your iOS device, open
Control Center and tap Screen
Mirroring.
2.Looking for devices that can
be mirrored on. 3.Select ZYCast-859c(mcast)
from the list.
Screen
Mirroring
Screen Mirroring
Looking for Apple TV... ZYCast-859c(mcast)
l. Focusing
Place the projector in a certain place within the required
distance so that the lens is perpendicular to the screen
then rotate the lens until the image is clear.
Screen Mirroring Mobile
Projector
Tab
Focus
Keystone
14. iOS Cast
Attention: The projector needs to be connected to the
network first when using Apple Airplay for the first time
or finishing the projector upgrade.
Step1: Select “iOS Cast” on the home screen.
Step2: iOS devices and projectors must be connected
to the same network, or connect the iOS device to the
wireless network issued by the projector.
Step3: Open the control center of iOS device, Choose
“Screen Mirroring”.
Step4: Choose on the name of the projector device.
Setup
iOS Cast
Miracast
8. Power On/Off
Connect the power cord to the projector and connect
the power cord to the outlet before the power is turned
on.
Once the projector is plugged in, it will be in
Standby mode.
Power on: Press the power button on the remote
control once to turn the projector on.
Power off: Press the power button on the remote
control twice to turn the projector off.
9. Focus/Keystone
ll. Keystone Correction
10. Setup
Set Submenu Function
Network:
Scan / Auto IP / Static IP / Disconnect
Projection:
Projection Mode: Front Desktop / Rear Desktop / Front
Ceiling / Rear Ceiling
Advanced:
Language / Boot Source / Sleep Timer / Local Update /
Online Update / Restore Factory Defauit
Step1: Choose “Setup” on the right of the interface,
then find “Network”.
11. WiFi Connection
Step2: Find “WiFi”.
Step3: Choose “Scan”. Select your wireless network
from list and type in the password.
Step4: Press the “Exit” key on the remote control and
then confirm the connection.
15. Miracast
Step1: Select the Miracast on the home screen.
Step2: Open the “wireless display” function of Android
device.
Step3: Select the corresponding projector device name.
Attention: Note that different Android devices have
different ways to open the “wireless display”. For
details, please refer to the instructions for Android
devices.
Media
12. Multimedia Play
Step1: Insert the USB flash drive into the projector's
USB interface.
Step2: Select “Media” and press “OK” to enter.
Step3: Select the file you like to play.
Step2: Make sure that the signal source you selected is
consistent with the access signal source.
1. Select your signal source: "HDMI", "VGA", "AV".
2. Customize your image settings. "Image Mode",
"Aspect Ratio","Brightness", "Contrast", "Color",
"Sharpness".
3. Customize your audio settings. "Sound Mode",
"Bass", "Treble", "Balance","Equalizer".
Source
13. Signal Source Settings
Step1: Press "OK" button to enter "Source".
Source
AV
VGA
HDMI
Image
Color
Sharpness
Contrast
Brightness
Aspect Ratio
Image Mode
Sound
Equalizer
Balance
Treble
Bass
Sound Mode
1
2
1. Focus
2. Keystone
Please adjust the "Keystone Correction" dial ring until
the image is displayed normally.
Note:The projector has only vertical keystone correction
and no horizontal correction.
Make sure your projector is level with the projected
image.
HOME> Setup> Projection
HOME> Setup> Network
HOME> Media> Movie
Movie Music
USB DISK
Photo Text
1/1
Network
WiFi Scan TP-LINK_E5A2
TP-LINK_E5A3
TP-LINK_E5A4
Auto IP
Static IP
Projection Advanced Information
Network Projection Advanced Information
Front Destktop
Projection Mode
disconnect
Miracast
Cast from Android Devices
1.On your Android Mobile/Tab,
open the settings menu.
2.Access your display settings or
screen-mirroring.
3.Select your Miracast
receiver: ZYCast-859c(mcast)
Wireless display
Connect to a display using WLAN
Mirror your iPhone or iPad
Make sure that your iOS device is connected to the same network as your
Prjector, or connect iOS device with AP by Projector: Projector AP
1.On your iOS device, open
Control Center and tap Screen
Mirroring.
2.Looking for devices that can
be mirrored on. 3.Select ZYCast-859c(mcast)
from the list.
Screen
Mirroring
Screen Mirroring
Looking for Apple TV... ZYCast-859c(mcast)
l. Focusing
Place the projector in a certain place within the required
distance so that the lens is perpendicular to the screen
then rotate the lens until the image is clear.
Screen Mirroring Mobile
Projector
Tab
Focus
Keystone
14. iOS Cast
Attention: The projector needs to be connected to the
network first when using Apple Airplay for the first time
or finishing the projector upgrade.
Step1: Select “iOS Cast” on the home screen.
Step2: iOS devices and projectors must be connected
to the same network, or connect the iOS device to the
wireless network issued by the projector.
Step3: Open the control center of iOS device, Choose
“Screen Mirroring”.
Step4: Choose on the name of the projector device.
Setup
iOS Cast
Miracast
8. Power On/Off
Connect the power cord to the projector and connect
the power cord to the outlet before the power is turned
on.
Once the projector is plugged in, it will be in
Standby mode.
Power on: Press the power button on the remote
control once to turn the projector on.
Power off: Press the power button on the remote
control twice to turn the projector off.
9. Focus/Keystone
ll. Keystone Correction
10. Setup
Set Submenu Function
Network:
Scan / Auto IP / Static IP / Disconnect
Projection:
Projection Mode: Front Desktop / Rear Desktop / Front
Ceiling / Rear Ceiling
Advanced:
Language / Boot Source / Sleep Timer / Local Update /
Online Update / Restore Factory Defauit
Step1: Choose “Setup” on the right of the interface,
then find “Network”.
11. WiFi Connection
Step2: Find “WiFi”.
Step3: Choose “Scan”. Select your wireless network
from list and type in the password.
Step4: Press the “Exit” key on the remote control and
then confirm the connection.
15. Miracast
Step1: Select the Miracast on the home screen.
Step2: Open the “wireless display” function of Android
device.
Step3: Select the corresponding projector device name.
Attention: Note that different Android devices have
different ways to open the “wireless display”. For
details, please refer to the instructions for Android
devices.
Media
12. Multimedia Play
Step1: Insert the USB flash drive into the projector's
USB interface.
Step2: Select “Media” and press “OK” to enter.
Step3: Select the file you like to play.
Step2: Make sure that the signal source you selected is
consistent with the access signal source.
1. Select your signal source: "HDMI", "VGA", "AV".
2. Customize your image settings. "Image Mode",
"Aspect Ratio","Brightness", "Contrast", "Color",
"Sharpness".
3. Customize your audio settings. "Sound Mode",
"Bass", "Treble", "Balance","Equalizer".
Source
13. Signal Source Settings
Step1: Press "OK" button to enter "Source".
Source
AV
VGA
HDMI
Image
Color
Sharpness
Contrast
Brightness
Aspect Ratio
Image Mode
Sound
Equalizer
Balance
Treble
Bass
Sound Mode
1
2
1. Focus
2. Keystone
Please adjust the "Keystone Correction" dial ring until
the image is displayed normally.
Note:The projector has only vertical keystone correction
and no horizontal correction.
Make sure your projector is level with the projected
image.
HOME> Setup> Projection
HOME> Setup> Network
HOME> Media> Movie
Movie Music
USB DISK
Photo Text
1/1
Network
WiFi Scan TP-LINK_E5A2
TP-LINK_E5A3
TP-LINK_E5A4
Auto IP
Static IP
Projection Advanced Information
Network Projection Advanced Information
Front Destktop
Projection Mode
disconnect
Miracast
Cast from Android Devices
1.On your Android Mobile/Tab,
open the settings menu.
2.Access your display settings or
screen-mirroring.
3.Select your Miracast
receiver: ZYCast-859c(mcast)
Wireless display
Connect to a display using WLAN
Mirror your iPhone or iPad
Make sure that your iOS device is connected to the same network as your
Prjector, or connect iOS device with AP by Projector: Projector AP
1.On your iOS device, open
Control Center and tap Screen
Mirroring.
2.Looking for devices that can
be mirrored on. 3.Select ZYCast-859c(mcast)
from the list.
Screen
Mirroring
Screen Mirroring
Looking for Apple TV... ZYCast-859c(mcast)
l. Focusing
Place the projector in a certain place within the required
distance so that the lens is perpendicular to the screen
then rotate the lens until the image is clear.
Screen Mirroring Mobile
Projector
Tab
Focus
Keystone
14. iOS Cast
Attention: The projector needs to be connected to the
network first when using Apple Airplay for the first time
or finishing the projector upgrade.
Step1: Select “iOS Cast” on the home screen.
Step2: iOS devices and projectors must be connected
to the same network, or connect the iOS device to the
wireless network issued by the projector.
Step3: Open the control center of iOS device, Choose
“Screen Mirroring”.
Step4: Choose on the name of the projector device.
Setup
iOS Cast
Miracast
8. Power On/Off
Connect the power cord to the projector and connect
the power cord to the outlet before the power is turned
on.
Once the projector is plugged in, it will be in
Standby mode.
Power on: Press the power button on the remote
control once to turn the projector on.
Power off: Press the power button on the remote
control twice to turn the projector off.
9. Focus/Keystone
ll. Keystone Correction
10. Setup
Set Submenu Function
Network:
Scan / Auto IP / Static IP / Disconnect
Projection:
Projection Mode: Front Desktop / Rear Desktop / Front
Ceiling / Rear Ceiling
Advanced:
Language / Boot Source / Sleep Timer / Local Update /
Online Update / Restore Factory Defauit
Step1: Choose “Setup” on the right of the interface,
then find “Network”.
11. WiFi Connection
Step2: Find “WiFi”.
Step3: Choose “Scan”. Select your wireless network
from list and type in the password.
Step4: Press the “Exit” key on the remote control and
then confirm the connection.
15. Miracast
Step1: Select the Miracast on the home screen.
Step2: Open the “wireless display” function of Android
device.
Step3: Select the corresponding projector device name.
Attention: Note that different Android devices have
different ways to open the “wireless display”. For
details, please refer to the instructions for Android
devices.
Media
12. Multimedia Play
Step1: Insert the USB flash drive into the projector's
USB interface.
Step2: Select “Media” and press “OK” to enter.
Step3: Select the file you like to play.
Step2: Make sure that the signal source you selected is
consistent with the access signal source.
1. Select your signal source: "HDMI", "VGA", "AV".
2. Customize your image settings. "Image Mode",
"Aspect Ratio","Brightness", "Contrast", "Color",
"Sharpness".
3. Customize your audio settings. "Sound Mode",
"Bass", "Treble", "Balance","Equalizer".
Source
13. Signal Source Settings
Step1: Press "OK" button to enter "Source".
Source
AV
VGA
HDMI
Image
Color
Sharpness
Contrast
Brightness
Aspect Ratio
Image Mode
Sound
Equalizer
Balance
Treble
Bass
Sound Mode
1
2
1. Focus
2. Keystone
Please adjust the "Keystone Correction" dial ring until
the image is displayed normally.
Note:The projector has only vertical keystone correction
and no horizontal correction.
Make sure your projector is level with the projected
image.
HOME> Setup> Projection
HOME> Setup> Network
HOME> Media> Movie
Movie Music
USB DISK
Photo Text
1/1
Network
WiFi Scan TP-LINK_E5A2
TP-LINK_E5A3
TP-LINK_E5A4
Auto IP
Static IP
Projection Advanced Information
Network Projection Advanced Information
Front Destktop
Projection Mode
disconnect
Miracast
Cast from Android Devices
1.On your Android Mobile/Tab,
open the settings menu.
2.Access your display settings or
screen-mirroring.
3.Select your Miracast
receiver: ZYCast-859c(mcast)
Wireless display
Connect to a display using WLAN
Mirror your iPhone or iPad
Make sure that your iOS device is connected to the same network as your
Prjector, or connect iOS device with AP by Projector: Projector AP
1.On your iOS device, open
Control Center and tap Screen
Mirroring.
2.Looking for devices that can
be mirrored on. 3.Select ZYCast-859c(mcast)
from the list.
Screen
Mirroring
Screen Mirroring
Looking for Apple TV... ZYCast-859c(mcast)
l. Focusing
Place the projector in a certain place within the required
distance so that the lens is perpendicular to the screen
then rotate the lens until the image is clear.
Screen Mirroring Mobile
Projector
Tab
Focus
Keystone
14. iOS Cast
Attention: The projector needs to be connected to the
network first when using Apple Airplay for the first time
or finishing the projector upgrade.
Step1: Select “iOS Cast” on the home screen.
Step2: iOS devices and projectors must be connected
to the same network, or connect the iOS device to the
wireless network issued by the projector.
Step3: Open the control center of iOS device, Choose
“Screen Mirroring”.
Step4: Choose on the name of the projector device.
Setup
iOS Cast
Miracast
8. Power On/Off
Connect the power cord to the projector and connect
the power cord to the outlet before the power is turned
on.
Once the projector is plugged in, it will be in
Standby mode.
Power on: Press the power button on the remote
control once to turn the projector on.
Power off: Press the power button on the remote
control twice to turn the projector off.
9. Focus/Keystone
ll. Keystone Correction
10. Setup
Set Submenu Function
Network:
Scan / Auto IP / Static IP / Disconnect
Projection:
Projection Mode: Front Desktop / Rear Desktop / Front
Ceiling / Rear Ceiling
Advanced:
Language / Boot Source / Sleep Timer / Local Update /
Online Update / Restore Factory Defauit
Step1: Choose “Setup” on the right of the interface,
then find “Network”.
11. WiFi Connection
Step2: Find “WiFi”.
Step3: Choose “Scan”. Select your wireless network
from list and type in the password.
Step4: Press the “Exit” key on the remote control and
then confirm the connection.
15. Miracast
Step1: Select the Miracast on the home screen.
Step2: Open the “wireless display” function of Android
device.
Step3: Select the corresponding projector device name.
Attention: Note that different Android devices have
different ways to open the “wireless display”. For
details, please refer to the instructions for Android
devices.
Media
12. Multimedia Play
Step1: Insert the USB flash drive into the projector's
USB interface.
Step2: Select “Media” and press “OK” to enter.
Step3: Select the file you like to play.
Step2: Make sure that the signal source you selected is
consistent with the access signal source.
1. Select your signal source: "HDMI", "VGA", "AV".
2. Customize your image settings. "Image Mode",
"Aspect Ratio","Brightness", "Contrast", "Color",
"Sharpness".
3. Customize your audio settings. "Sound Mode",
"Bass", "Treble", "Balance","Equalizer".
Source
13. Signal Source Settings
Step1: Press "OK" button to enter "Source".
Source
AV
VGA
HDMI
Image
Color
Sharpness
Contrast
Brightness
Aspect Ratio
Image Mode
Sound
Equalizer
Balance
Treble
Bass
Sound Mode
1
2
1. Focus
2. Keystone
Please adjust the "Keystone Correction" dial ring until
the image is displayed normally.
Note:The projector has only vertical keystone correction
and no horizontal correction.
Make sure your projector is level with the projected
image.
HOME> Setup> Projection
HOME> Setup> Network
HOME> Media> Movie
Movie Music
USB DISK
Photo Text
1/1
Network
WiFi Scan TP-LINK_E5A2
TP-LINK_E5A3
TP-LINK_E5A4
Auto IP
Static IP
Projection Advanced Information
Network Projection Advanced Information
Front Destktop
Projection Mode
disconnect
Miracast
Cast from Android Devices
1.On your Android Mobile/Tab,
open the settings menu.
2.Access your display settings or
screen-mirroring.
3.Select your Miracast
receiver: ZYCast-859c(mcast)
Wireless display
Connect to a display using WLAN
Mirror your iPhone or iPad
Make sure that your iOS device is connected to the same network as your
Prjector, or connect iOS device with AP by Projector: Projector AP
1.On your iOS device, open
Control Center and tap Screen
Mirroring.
2.Looking for devices that can
be mirrored on. 3.Select ZYCast-859c(mcast)
from the list.
Screen
Mirroring
Screen Mirroring
Looking for Apple TV... ZYCast-859c(mcast)
l. Focusing
Place the projector in a certain place within the required
distance so that the lens is perpendicular to the screen
then rotate the lens until the image is clear.
Screen Mirroring Mobile
Projector
Tab
Focus
Keystone
Table of contents
